PVC reveals
Sandwich panels cover the installation seam in one visit. From 4 700 ₸ per linear metre.


PVC reveals
Sandwich panels cover the installation seam in one visit. From 4 700 ₸ per linear metre.

Whole window
Three sides, corners and joints for a standard window. From 15 000 ₸ per window.

Plaster
We level and fill for painting to match the walls. From 3 000 ₸ per linear metre.


Insulation
A warm layer under the reveal removes the dew point. From 19 900 ₸ per linear metre.

4,9137 reviews
The reveal covers the installation seam around the window, and its quality determines whether the corner stays warm and dry
After window installation, foam remains around the frame. Without protection it darkens and breaks down from light and moisture, and the seam starts letting in cold. The internal reveal covers the foam from inside, the external reveal from outside.
Inside we fit PVC sandwich panels, plastered or plasterboard reveals, and with mould and condensation — with insulation. Outside we make external reveals, seal the seams and fit a drip sill.

sandwich panels per linear metre
turnkey window
measuring and consultation
The four most common complaints after window replacement

After window installation the seam is exposed. We cover it with PVC reveals, and the foam no longer breaks down.
The old reveal cracked from temperature changes. We fit sandwich panels over it.
A cold reveal gets damp. We insulate and finish it anew.
Moisture on the reveal due to the dew point. A warm layer solves the problem.
We choose the material based on the room, budget and wall condition
Panel with insulation

Fast, neat, washable, resistant to moisture.
For painting

A classic for flats with even walls.
Dry installation

Inexpensive, for dry rooms.
From outside

Protect the foam and seam outside.
Against condensation

For cold corners and mould.
Cost per linear metre or window, final price after measuring
| Type of work | Price |
|---|---|
| PVC reveals (sandwich panels), per linear metrepanel with insulation inside | from 4 700₸ per linear metre |
| Reveals for a standard window, turnkeythree sides and corners | from 15 000₸ per window |
| Plastered revealswith levelling and filling | from 3 000₸ per linear metre |
| External revealsprotects the seam from outside | from 4 500₸ per linear metre |
| Plasterboard revealsready for painting | from 1 500₸ per linear metre |
| Reveal insulationagainst freezing and condensation | from 19 900₸ per linear metre |
| PVC windowsill fittingtogether with reveals | from 5 500₸ per linear metre |
| Drip sill fittingdrains water away from the frame | from 3 250₸ per linear metre |
| Sealing internal seams (liquid plastic)joints of frame, reveal and windowsill | from 1 500₸ per linear metre |
| Sealing external seamsprotects foam from moisture and sun | from 2 000₸ per linear metre |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after work: cash, card, Kaspi
Book a measuring visitHow we work
we work across Kazakhstan
on WhatsApp
Andrey Nasonovat a convenient time
does not change after measuring
acceptance: cash, card, Kaspi
no days off
plastic, wood, aluminium
we install it together with the reveals
Four steps from photo to a clean window

Send a photo of the window and reveals on WhatsApp. We will reply and suggest a time for measuring.

The measurer inspects the seam and the wall, selects the material and gives the order price.

We cut off excess foam, insulate if needed, install the reveals and seal the joints.

We check the corners and seams and clean up. Payment after acceptance.
Three orders from Almaty: what the issue was and what we did.
New buildingIn a new building, after window installation, exposed yellow foam remained around the frames.
We cut off excess foam and covered the seam with PVC sandwich panel reveals.
The windows look finished, and the seam is protected from light and moisture.
Five-storey blockIn a brick five-storey block, the plastered reveals had cracked and were crumbling at the corners.
We removed the loose plaster and installed sandwich panels.
No cracks, the reveals are even and easy to clean.
Private houseIn a private house, mould appeared on the bedroom window reveals every winter.
We treated the wall, insulated the reveal and finished it with sandwich panels.
The corner stays dry, and the mould does not return.
Our team — makers and installers





Good to know
We handle window reveal finishing in Almaty as a direct contractor, not a middleman. Our own measurer visits for free, helps pick the material and colour, and our own fitters install the reveals on plastic, wooden and aluminium windows, balcony doors and loggias. The price is fixed in the order after measuring, and you pay after installation.
The reveal material decides how an opening copes with damp, cold and sun. We compare plastic with sandwich panels and explain when an outer reveal earns its place.
We fit both PVC reveals and sandwich panels, and the right pick depends on the wall, the room humidity and how much insulation the slope needs. A PVC board clips onto the frame and wipes clean with a damp cloth, which suits kitchens, bathrooms and hallways where grease and steam settle fast. The composite version is built from two hard skins with an insulating core between them, so it holds warmth on a cold outer wall and stiffens the slope without extra battens. In our practice, panel-block flats on the windward side gain the most from the insulated option, while interior partitions rarely justify it.
An external reveal protects the joint from rain and wind, and we match its colour to your opening so the finish looks like one piece. The mounting joint between frame and wall is the weakest line in any opening: driven rain works into the gap, freezes, and widens it season after season. A sloped cover caps that line and throws water clear of the frame, and the inside and outside slopes then read as a single tidy surround. Colour matching is straightforward — we paint the slope frame to the profile shade, so white stays white and laminated finishes keep their tone. Skipping this cover leaves the joint open to water, later showing as damp patches inside.
| Reveal type | Made of | Best for | Moisture behaviour |
|---|---|---|---|
| PVC reveal | rigid plastic panel | kitchens, bathrooms, easy cleaning | does not absorb water |
| Sandwich panel | two skins with insulating core | cold outer walls, extra warmth | sealed surface, insulated core |
| Plastered reveal | plaster over mesh | painted interiors, custom shapes | needs sealing and paint |
The job runs in a clear order, from the free measuring visit to the finished reveal, and each step has its own timing you can plan around.
Fitting order, fixings and whether old reveals come off We fit reveals right after the glazing goes in, fix them to the frame with brackets or adhesive foam, and strip loose old panels first. Fresh foam fills the gap between sash and opening, so the new surface rests on a solid base. On a sound old slope we can fix straight over it and save you a day of work. A damp or crumbling panel has to come off, or the finish will not sit flat and the joints open within a season. Window reveal finishing in Almaty follows the same order on every site, so the fitter checks the fixing points twice before the panel goes on upper floors.
| Stage | What happens | Who does it |
|---|---|---|
| Measuring | sizes taken, material and colour chosen | specialist, free visit |
| Making | panels cut to the measured sizes | our own workshop |
| Fitting | panels fixed to the wall, joints sealed | our fitters |
| Handover | you check the slopes and joints | you and the fitter |
An uneven wall or cold slope is where reveal work earns its keep, and buyers worry about these cases most, both solved in the gap before cutting any panel.
We put insulation into the reveal gap and seal it with vapour and water-proof tapes, which keeps the inner slope warm enough to stop condensation. Mineral wool or foam board goes in first, pressed tight without gaps at the corner where the slope meets the unit. A vapour barrier on the warm side stops room moisture from reaching the cold zone, and a waterproof tape on the outer face keeps driving rain and meltwater out of the joint. A taped, sealed node holds, while a foam-only joint opens as the frame moves with temperature. Condensation on a reveal means the joint is cold.
Once the panels are on, a short check and simple care keep the reveal looking right for years, and the warranty covers the work behind it.
A well-fitted reveal has even joints, no gap at the frame and a slope that does not flex when pressed, and we walk you through these points at handover. Check the mitre where two panels meet: the seam should be tight and level, with no step between surfaces. Press the panel near the frame and in the middle; a firm piece gives no movement, while a soft spot means the fixing behind it is short. Look along the joint at eye level — the line should stay straight from corner to corner. Run a hand along the frame joint before you sign off, because a thin gap there is the first place draughts and damp will show.
Wipe PVC reveals with a soft cloth and mild soap, avoid abrasive pads, and the warranty covers our fitting work and the parts we replaced. Dust settles on the slope within a month, so a damp cloth once a season keeps the surface even. Grease near a kitchen opening needs a drop of dish soap, not a strong agent. Our repair service carries a one-year warranty on labour and replaced parts, and installation is covered for five years, so a joint that opens or a panel that lifts is a warranty call, not a paid visit. A solvent cleaner dulls the surface, and that wear is not a fitting fault.
Balcony doors, glazed loggias and garden structures each need their own fitting detail, and the fixing must match what the panel is anchored to.
We fit reveals on balcony doors, glazed loggias, verandas and gazebo openings; a door reveal needs stronger fixing because the panel runs to the ground. The specialist picks the fastener to suit the profile and sill level rather than reusing the standard bracket. On enclosed terraces the trim often meets a tiled sill on one edge and bare concrete on the other, so both sides are checked before cutting. Veranda and gazebo openings are exposed to wind and rain, so the outer joint is sealed with more care than indoors. A door reveal meets the ground, so the bottom joint needs a seal that takes foot traffic and cleaning without lifting.
You can order reveals from us even if another company fitted the units, and the specialist checks the existing sash before quoting. Plastic, wooden and aluminium frames behave differently at the edge: a timber frame may have swelled or shrunk since installation, while an aluminium one often sits tighter against the wall. The measuring visit is free, and the specialist records the actual opening rather than the nominal size. A sash fitted by someone else may sit slightly out of square, so the measuring visit matters more here. We make and fit reveals with our own crews, so nothing is passed to a subcontractor.
A reveal job holds up when the material, the measuring and the fastening all match the opening in front of you. These are the points worth carrying into the order.
Materials, repair, insulation, installation
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionMost often, sandwich panels with insulation inside and standard PVC panels without it are used. The former retain heat better, the latter are lighter — the choice depends on the window and the room.
Yes, the window does not need to be removed for reveal repair: the work is done on the inner opening around the frame. The technician carefully removes damaged panels or plaster without affecting the structure itself.
The foam does not gain strength immediately, and only when it has fully set is it trimmed and plastered. The exact time depends on the layer thickness and the room temperature.
For humid rooms, sandwich panels and plastic are suitable: they are not afraid of water and are easy to clean. Plaster is used there less often — it requires protection and tolerates constant dampness worse.
Insulation is worthwhile if the reveal freezes or condensation appears on it. Mineral wool, penoplex, or expanding foam are chosen based on the opening design — the decision depends on the window and wall thickness.
Turnkey includes measuring, preparing the opening, insulation and sealing of seams, installation of panels or plaster, and finishing. The technician removes the old reveals and cleans up debris after the work.
Сетки на все окна поставили за один день. Мастер приехал ровно к девяти, как и обещал. После монтажа на подоконниках ни пыли, ни стружки — вот это удивило больше всего
Долго откладывал это дело, казалось мелочью, которую можно сделать потом. В итоге к августу в квартире стало невозможно спать: окна закрыты, духота, кондиционера нет. Позвонил в понедельник, во вторник утром у меня уже были замерщики с рулеткой и лазерным уровнем. Объяснили разницу между рамной и раздвижной, посоветовали на кухню обычную, а на балкон раздвижную, чтобы удобнее выходить. Монтаж занял часа три на четыре окна. Ребята приехали со своим инструментом, после себя всё убрали, даже пропылесосили. Сейчас открываю балкон одной рукой и никакой живности в доме. Жалею только, что не сделал этого раньше.
Сделали на дачу в пригороде, куда летом приезжают внуки — комары их просто едят. Приехали вобщем вовремя всё поставили, ещё и старую сетку сняли бесплатно. Спасибо
Ескі үйдің ағаш терезелеріне сетка іздеп жүрдім, көп компаниялар «профиль дұрыс емес» деп бас тартты. Бұл жерде бірден келісті, бұрыштарға бекітіп, артық тесік бұрғыламай орнатты. Екінші маусым, әлі мықтап тұр.
Меняли стеклопакеты на балконе, решили сразу сделать и отделку откосов. Всё выглядит очень эстетично, стыки аккуратные. По срокам успели даже быстрее, чем обещали.
После монтажа окон нужно было сделать откосы. Мастер приехал в удобное время, всё посмотрел и объяснил по материалам. Работу выполнили аккуратно, откосы выглядят ровно и чисто 😊💯
Делали ремонт откосов и поставили рамочную сетку на форточку. Мастер предупредил что потребуется время на подгонку рамы но работа стоит того Они аккуратно сняли старую уплотнитель заменили и поставили новую сетку Теперь становится тише и хлебные крошки не лезут на окно Домочадцы довольны особенно бабушка которая боится комаров Рекомендую без навязчивости цена была честная по телефону сказали скидку но потом не подтвердили мелочь но работу сделали хорошо гарантия на монтаж есть и оставили инструкции как ухаживать спасибо им
Жазда үй іші ысып кетпесін деп веранда мен мансардалық терезелерге маскитка салдырдық. Антикошка дегенін таңдадық, өйткені үйде екі мысық бар, сетканы тырнап жібереді деп қорыққанбыз. Полотносы шынымен тығыз, бірақ сырттағы ауа жақсы өтеді, бөлме қапырық болмайды. Замерді тез алып, ертесі күні келіп орнатып кетті, артық әңгіме жоқ, бағасы да базармен салыстырганда қалыпты. Ұнады, күзде енді ескі терезелердің откосын да осыларға жөндетемін
Менял окна в квартире. Замерщик приехал вовремя, всё объяснил по профилю и стеклопакету. Монтаж сделали аккуратно: створки работают плавно, откосы ровные, нигде не продувает. После установки дома стало заметно тише и теплее
Меняли старые окна на пластиковые, все сделали за день не запачкали откосы и подоконник. Ребята молодцы, работали четко и аккуратно
Запросил установку новые откосы, мастер пришел вовремя и все сделал отлично. Я не ожидал, что будет так быстро. Рекомендую!
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp