Technician holding a new white PVC window handle in a country house
from 3,000 tg per sashFree visit and inspection in Almaty, WhatsApp reply within 5 minutesCalculate

Window Repair in Almaty

Pressure and hardware

Sash adjustment

Simple sash adjustment — from 3,000 tg per sash. The technician will tighten the pressure and check how the hardware moves.

A craftsman holds an L-shaped steel hex key for adjusting hinges
GoogleYandex MapsZoon

4,9137 reviews

What window repair includes

Restoring the operation of the sash, hardware and sealing contour without replacing the entire window

How the service works

Window repair is adjusting mechanisms and replacing worn parts: sash, hardware, seal, glass unit. The technician visits your address, inspects the window and eliminates the cause of the failure.

In Almaty, the visit and inspection are free. We provide a 1-year warranty on work and replaced components, and reply in WhatsApp within 5 minutes.

Technician in a dark blue T-shirt with a hex key at an open white PVC window sash
1 year

warranty on work and components

Free

visit and inspection in Almaty

5 minutes

reply in WhatsApp

6 works
AdjustmentSealHandleHingesGlass unit

How sash and hardware failures are fixed

Six typical requests and what is done about them on site

Close-up of an L-shaped hex key in the trunnion on the edge of an open white PVC window sash
  • 01Whistling and drafts in windy weather

    Checking the sealing contour around the sash perimeter.

  • 02The sash does not reach the frame, the handle turns with effort

    Diagnostics of locking points and sash movement.

  • 03The sash has sagged

    Hinge adjustment lifts the sash and eliminates rubbing against the frame.

  • 04The handle is broken

    Replacing the handle with a compatible model for your profile.

  • 05Condensation and mold

    Adjustment, seal replacement and slope insulation eliminate the cause of moisture.

  • 06The glass unit has cracked

    Glass unit replacement restores glazing and thermal insulation.

Types of window repair work we perform

Five repair directions with an 'from' price; the exact cost will be quoted by the technician after inspection

Pressure adjustment

Simple or complex

A craftsman holds an L-shaped steel hex key for adjusting hinges

Adjusting the sash pressure against the frame along the entire contour

from 3 000 ₸

Seal replacement

Around the sash perimeter

Technician holds a roll of grey rubber seal, showing it for replacement

A new sealing contour instead of a worn one

from 1 000 ₸/linear m

Hinge replacement

Sash hinges

A craftsman holds a new white plastic window handle for replacement

Replacing worn hinges with compatible ones

from 4 750 ₸

Hardware repair

Locking mechanism

A craftsman holds a roll of gray mosquito netting for repair

Restoring the operation of the sash hardware

from 7 800 ₸

Glass unit replacement

Glass and sealant

A craftsman holds a small square double-glazed unit sample for replacement

A new glass unit to fit the opening size

from 19 500 ₸/m²

Window repair prices in Almaty

Price list of works; the final price is fixed in the order after measuring

Type of workPrice
Master visit and inspectionwithout ordering a repairfrom 3 600₸ per job
Simple sash adjustmentfrom 3 000₸ per sash
Complex adjustment with sash removalfrom 4 000₸ per sash
Window handle replacementfrom 2 750₸ per pc
Hinge replacementfrom 4 750₸ per pc
Hardware repairfrom 7 800₸ per job
Hardware replacement on the sashfrom 10 000₸ per sash
Seal replacementfrom 1 000₸ per linear m
Glass unit replacementfrom 19 500₸ per m²
Broken glass replacementfrom 8 000₸ per m²
PVC window sill installationfrom 5 500₸ per linear m
Window flashing installationfrom 3 250₸ per linear m
Mosquito net repairfrom 2 500₸ per pc
Supply valve installationfrom 6 000₸ per pc

The price is fixed in the order after measuringFree visit and inspection in AlmatyPayment after installation: cash, card or Kaspi

Check the price

Why customers order window restoration from us

Facts about the company: guarantees, visits, payment and working hours

Experiencesince 2012

we work across Kazakhstan

Double glazing warranty3 years

for double glazing replacement

Installation warranty1 year

for installation work

Visit in Almatyfree

technician visit and inspection within the city

Paymentafter

payment after installation: cash, card or Kaspi

Schedule09:00–22:00

daily, open seven days a week

WhatsApp reply5 minutes

we reply on WhatsApp within 5 minutes

Coverage17 cities

you can order in 17 cities of Kazakhstan

How window repair is carried out

Four steps from request to checking the work

  1. A hand holds a smartphone with a dark screen near a white PVC window
    015 minutes

    Request

    You write on WhatsApp or call, describe the problem. We reply within 5 minutes.

  2. A tape measure measures the lower edge of the window opening of a white PVC window
    02at a convenient time

    Visit and inspection

    The technician arrives at a convenient time, inspects the window and names the cause of the fault.

  3. A removed white window sash on a workbench next to a coil of new black seal
    03on site

    Work

    The technician performs adjustment or replacement of parts on site, bringing the necessary components.

  4. A finished white PVC window with a new seal and handle, the sash closed evenly
    04after work

    Check

    You accept the work according to your checklist: check the handle movement, that the sash does not catch, and that it is level. The technician records the result in the report.

Window restoration order stories

Three requests from this page: what was and what was done

Technician holds a new black seal by an office window in a business center, Almaty mountains behind the glassOffice in a business centre
Object
Office
Problem
Draught from under the sash
Work
Adjustment and seal
  1. Request

    There is a draught from under the sash, the office is cool even with the window closed.

  2. What we did

    Adjusted the sash pressure and replaced the seal around the sash.

  3. Result

    The sash fits tightly, the draught is eliminated.

I want the same
A craftsman adjusts window hardware in a child's room so the sash closes completelyChildren's room
Object
Apartment
Problem
Window does not close
Work
Hardware adjustment
  1. Request

    The window in the children's room does not close fully, the sash remains ajar.

  2. What we did

    Adjusted the hardware, restored the movement of the locking mechanism.

  3. Result

    The sash closes fully, the lock works.

I want the same
Technician checking the movement of a sagging window sash before adjusting the hinges, kitchen with a gas stoveKitchen with a gas stove
Object
Kitchen
Problem
Sash sagged
Work
Hinge adjustment
  1. Request

    The sash has sagged and catches the frame when closing.

  2. What we did

    Adjusted the hinges, set the sash level.

  3. Result

    The sash moves freely without catching the frame.

I want the same

Who will complete your window repair order in Almaty

1/5

Our team — makers and installers

Konstantin Selenenkov, Senior mosquito screen specialist
Konstantin SelenenkovSenior mosquito screen specialist
  • 10 years in the trade
  • Production, Tole bi, 83

Production

Andrey Nasonov, Mosquito screen fitting specialist
Andrey NasonovMosquito screen fitting specialist
  • 10 years in the trade
  • Almaty, all districts

FittingMesh selection

Mukhameddin I., Mosquito screen manufacturing specialist
Mukhameddin I.Mosquito screen manufacturing specialist
  • 15 years in the trade
  • Production, Tole bi, 83

Framed

Kanagat Turdan, Pleated screen specialist
Kanagat TurdanPleated screen specialist
  • 11 years in the trade
  • Production, Tole bi, 83

Pleated

Khairullo Mutalov, Anti-Cat screen fitter
Khairullo MutalovAnti-Cat screen fitter
  • 16 years in the trade
  • Almaty, all districts

FittingScreen repair

Good to know

Window Repair in Almaty from Our Own Masters with a Free Inspection

We handle window repair in Almaty with our own masters and workshop, not through an aggregator. We come for a free inspection anywhere in the city, diagnose the window, and fix what can be fixed: adjustment, seals on any profile, glass units, insulation. The price is fixed after measuring, and you pay once the work is done.

Can Your Window Be Repaired or Does It Need Replacing

Almost any glazing complaint can be solved by repair, and full replacement is needed far less often than people expect. Below is how to tell one from the other before a master arrives.

Which faults are fixed by repair and which need a new unit

  • Draught along the frame: a worn gasket or loose fittings, fixed by a fresh gasket or adjustment.
  • Sash that scrapes or catches: shifted geometry, corrected by re-hanging and adjusting the hardware.
  • Fog or condensation between the panes: a failed double-glazed unit, replaced as a single sealed assembly.
  • Cracked frame or broken profile: structural damage that usually means a full replacement.
  • Stiff handle or lock: worn hardware, repaired or swapped without touching the surround.

When adjustment, a new seal or a glass unit is the right call

We match the fix to the symptom: a sash that catches calls for adjustment, a draught along the surround calls for a fresh gasket, and fog between the panes calls for a new double-glazed unit. Adjustment corrects the clamping pressure and brings the sash back to square, which is why a leaf that no longer closes tightly often needs no parts at all. A fresh gasket restores the airtight line and is replaced on any profile brand, including KBE, Rehau, VEKA and Provedal. The glass is swapped when the seal between its panes has failed and moisture has clouded the gap. Replacing it on a unit whose gasket is worn just moves the problem, so we check the seal before ordering glass.

Can a fixed pane be made to open

A fixed pane can be converted into an opening sash, and in new buildings we often re-set a leaf that was fitted out of square rather than replace anything. The work means fitting new hardware to the existing surround and cutting the panel open where the profile allows it. Window repair in Almaty new-build flats rarely involves the outer structure itself, because the profile arrives sound and the fault sits in the installation geometry. A re-hang and adjustment of the hardware therefore costs far less than a full replacement and keeps the original glazing. On older wooden units the answer depends on the condition of the timber around the opening, which the master checks before promising the conversion.

Common Window Problems and How We Fix Them

Most calls start with a symptom the owner can see or feel: a draught, a sash that catches, water on the sill. Below are the four most frequent complaints and what usually sits behind each one.

Cold air coming through the glazing in winter

Cold air in winter is usually a worn seal or a loose sash clamp, and we fix both on the same visit without touching the glass. A seal flattens after several seasons of heat and frost, so the sash no longer presses against the frame evenly. The clamp is the hardware that pulls the sash tight when you turn the handle, and it drifts out of setting over time. We replace the seal and adjust the clamp in one pass, then check the result by hand along the whole perimeter. A draught that appears only on windy days points to the seal, while a constant cold strip along the hinge side points to the clamp — the two need different parts.

A sagging sash that scrapes the frame

A sash that scrapes has dropped on its hinges, and we re-hang and adjust it so it closes with a light pull and no contact with the frame. The cause is weight: a double-glazed sash is heavy, and the lower hinge carries most of it, so the corner gradually sinks a few millimetres. We loosen the hinge, lift the sash back into line, set the geometry and tighten the fixings again. The same visit covers the clamp setting, so the sash presses evenly top and bottom. Left alone, a scraping sash wears the seal and the hinge, so a small adjustment now avoids a parts replacement later.

Condensation and mould around the frame

Condensation on the glass is normal in cold weather, but water and mould on the frame or slope mean the unit is losing heat at the joint, not at the glass. Warm indoor air meets a cold surface, and the coldest point sits where the frame meets the wall or under the sill. A failed seal, a thin insulation layer or a slope with a gap lets that cold through. Wiping mould only hides it; the source is a cold bridge at the frame or slope, so the fix is insulation and a new seal, not a new glass unit.

What Happens During a Window Repair Visit

A master's visit is an inspection, a decision, the work itself and a check at the end. Below is what actually happens inside your flat and at which point you pay.

The free inspection and what the master checks

In Almaty the master's visit and inspection within the city are free, and he checks the frame geometry, the gasket, the hinges and the glass before naming a fix. He runs a level along the sash, tests the handle and tilt mechanism, looks for gaps where the weatherstrip has flattened and taps the glass unit for a dull sound that points to a broken barrier inside. On the spot he tells you whether adjustment, a fresh gasket or a new unit is the answer, and what each option involves. The inspection happens before any part is ordered, so you see the diagnosis and the plan before committing to the work. Ask him to show you the worn strip or the loose hinge — a fault you can see is easier to accept than one you are only told about.

How the price is fixed and when you pay

The price is fixed in the order after measuring, and you pay after the work is done by cash, card or Kaspi. Measuring comes first because a sash that is out of square by a few millimetres changes which parts the job needs, and a figure quoted over the phone would be a guess. Once the measurer has the sizes, the number is written into the order and stays there. A figure fixed after measuring means the amount you agree to on site is the amount you pay, with no add-ons discovered mid-job. Keep the order sheet — it lists the parts and the labour the warranty will later refer to, so it is worth filing rather than leaving on the kitchen table.

Insulation, slopes and sills in the same visit

Insulation, slopes and sills can be handled in the same visit as the repair, so the unit is finished in a single appointment instead of three. Cold air at a plastic frame usually travels in at two points — the gasket line and the joint where the frame meets the wall — and treating only one of them leaves the other open. Doing the weatherstrip and the slope together closes the cold bridge in a single go, which is why we plan them as one job rather than separate call-outs. A sill that has pulled away from the frame is reseated at the same time, since the gap behind it is part of the same cold path. Book the full scope in a single message on WhatsApp and the master arrives with the materials for all of it.

Window Types and Profiles We Work With

Frames differ by material and by profile, and the right repair follows from both. We handle all three frame types and match seals to the profile rather than to the brand on the handle.

Plastic, aluminium and wooden units in one place

We repair plastic, aluminium and wooden units, including balcony and panoramic glazing, with the same masters and the same one-year repair warranty. Plastic units usually need adjustment or a fresh seal; aluminium rarely warps but its seals harden faster, and wooden sashes shrink and sag with the seasons, so a re-hang and adjustment come first. Balcony and panoramic glazing most often lose heat at the joints between sections, where the seal and insulation do the work. The material decides the tool kit, the fasteners and the time on site, not a single script applied to every frame. On aluminium, check the seal before blaming the glass — a hardened gasket reads as a draught long before the unit itself fails.

Seals for any profile brand

We replace the seal on units of any manufacturer, including KBE, Rehau, VEKA and Provedal, because the seal is matched to the profile, not to the brand. The profile brand decides which seal cross-section fits, so tell us the brand or send a photo of the frame edge and we bring the right one on the visit. A seal that is too thin leaves a gap, and one that is too thick stops the sash closing flush, so the cross-section matters more than the label. We change the gasket around the sash and the frame, and check the corners where most leaks start. Send the brand name or a close-up of the frame edge before the visit — it saves a second trip and gets the correct seal on the first attempt.

Matching the fix to the frame type

faults and fixes by frame material
Window typeCommon faultTypical fix
Plastic (PVC)Loose clamp, worn sealAdjustment, new seal
AluminiumHardened seal, draughtSeal replacement, insulation
WoodenShrunken frame, sagging sashRe-hang, seal, adjustment
Balcony / panoramicDraught at jointsSeal and insulation

Warranty and What It Actually Covers

A promise in a sales pitch and a promise you can claim on are two different things. Here is what we cover, for how long, and where the line sits.

One year on repair, three on glass, five on installation

We back window repair for twelve months — labour and replaced parts included — glass unit replacement for three years, and installation for five. The periods differ because each job is a different animal: a repair touches a mechanism or a seal, a glass unit is a sealed factory component, and installation is the whole frame sitting in the opening. Every term is written into the order after measuring, so the clock starts the day the work is finished, not the day you first called. Coverage follows the part rather than the visit, so a glass unit still inside its three-year term remains protected even if the repair call happened long ago.

What the repair warranty covers and what it does not

The twelve-month cover includes our labour and every part we swapped, so if the same fault returns we come back at no charge. That means the sash that starts scraping again, the handle we changed, the seal we fitted — all of it sits under the same period. It does not stretch to damage from a broken hinge or a forced sash, or a unit knocked out of adjustment by building work or a heavy impact. That is precisely why we check the whole fitting during the visit, not just the reported fault: a hinge already bending under load is caught before it tears out of the profile, and anything recorded on the day is something we can stand behind later.

Why own masters and a workshop matter for warranty

Our own fitters and screen workshop in Almaty mean the person who fixes your unit is the person we answer for, with no middleman between you and the cover. A crew that arrives from a dispatch list has no reason to record what it found, and a contractor you never chose ends up holding the obligation. Our team works the same routes every week, logs the parts it replaces, and hands the job back to the workshop if something needs remaking. With an aggregator the assurance sits with a stranger you never picked, so a direct executor is the only way it keeps one clear owner.

How Fast We Work and How the Price Is Set

Two questions come up in almost every call: how quickly the job can be done and what the final bill will depend on. Both are answered by timing and by the parts involved.

A glass unit replaced within one day

An urgent order for a sealed unit is made and fitted within one day, with a surcharge on its price, while standard orders follow the usual schedule. The pane is measured on site, assembled to the frame size and swapped without touching the sashes or the profile. A broken pane that leaves the room open to wind and cold is the case where the urgent route earns its surcharge. A foggy one that still holds heat and keeps draughts out can go on a standard order without risk to the flat. Moisture inside the sealed cavity means the seal has failed, not that the pane is about to crack, so the swap is about clarity and insulation rather than safety. On urgent orders we ask for frame photos in advance so the replacement arrives the right size.

Seven days a week and a five-minute reply

We work seven days a week, from 09:00 to 22:00 in Almaty, and answer WhatsApp messages within five minutes during those hours. Weekend calls are handled the same way as weekday ones, so a sash that will not close on a Sunday does not wait until Monday. The five-minute reply is a person reading the message, not an auto-responder, and it usually comes with the next free slot for a visit. A photo of the frame plus the profile brand speeds this up further: the master can name the likely fault and the part needed before setting foot in the flat. For a symptom that looks urgent — a sash hanging open, a pane cracked through — say so in the first line.

What decides the price of a repair

  • The fault itself: a dropped sash needs adjustment, a failed seal needs a new gasket, a misted cavity needs a swap.
  • The parts involved: hinges, handles, seal profiles and panes differ in cost, and the profile brand narrows the choice.
  • The frame type: plastic, aluminium and wooden frames take different fittings and different labour time.
  • Access and height: a unit on an upper floor or behind furniture takes longer to reach and work on.
  • The final figure: the price is fixed in the order after measuring, never quoted as a firm number over the phone.

Where to start when the sash closes poorly

Most complaints about glazing turn out to be straightforward fixes, and the visit itself is what settles the repair-or-replace question for good.

  • Repair first, replace rarely: draughts, sagging sashes, worn gaskets and foggy glass are fixable; a cracked frame or broken profile is not.
  • Symptom before material: identify what the unit is doing wrong, then match the fix to plastic, aluminium or wood before ordering any part.
  • Predictable from the start: a free inspection and a price fixed after measuring remove the guesswork from the first visit onward.
  • Gaskets fit any brand: replacement strips are matched to the profile maker, so KBE, Rehau, VEKA and Provedal systems are all serviceable.
  • Warranty follows the part: labour and replaced parts, glass units and installation each carry their own term, so read them separately.

Questions about window repair

Repair or replacement, adjustment, choosing a technician, seal

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can the window be repaired or is it easier to install a new one?

Most often, the window can be repaired if the profile and double glazing are intact and the problem is with the hardware or seal. Replacement is needed when the frame is deformed or the double glazing is damaged. A technician will tell you for sure during the inspection.

02What does the adjustment of plastic windows during repair include?

Adjustment includes setting the sash pressure, aligning the hinges, and lubricating the mechanisms. If needed, the technician will replace the seal or handle. The exact list depends on the condition of the window.

03How to choose a window repair technician in Almaty to avoid rework?

Look at reviews and ask whether they provide a warranty on work and components. It is better to contact a company with its own technicians rather than intermediaries.

04Can a wooden window be repaired or does it have to be replaced?

Yes, wooden windows can also be repaired: hardware and seals are replaced, and sash misalignments are fixed. But the techniques differ from plastic, so an experienced technician is needed.

05Can the seal in a KBE or Rehau window be replaced in Almaty?

Yes, we replace seals in windows of any manufacturer, including KBE, Rehau, and VEKA. We select a suitable profile and install a new one around the sash perimeter. The work and components are covered by a warranty.

★★★★★
Сетки на все окна поставили за один день. Мастер приехал ровно к девяти, как и обещал. После монтажа на подоконниках ни пыли, ни стружки — вот это удивило больше всего
Айгуль К.May 14, 2023 · from our order database
★★★★★
Сделали на дачу в пригороде, куда летом приезжают внуки — комары их просто едят. Приехали вобщем вовремя всё поставили, ещё и старую сетку сняли бесплатно. Спасибо
Марина Ж.June 18, 2020 · from our order database
★★★★★
Хотела написать коротко, но получится длинно. Мы делали ремонт, меняли все окна, и я заранее переживала, что сетки будут выбиваться из общего вида. Приехал замерщик, показал образцы профиля, дал потрогать полотно, объяснил, что белый стандарт подойдёт идеально. Потом позвонили из офиса, согласовали дату. В день монтажа приехали двое, работали спокойно, без спешки, на пол подложили плёнку. На одном окне оказался небольшой перекос после установки — мастер заметил сам и подправил крепление, хотя я бы и не увидела. Вот это отношение. Теперь рекомендую всем знакомым.
Ирина В.July 12, 2017 · from our order database
★★★★★
Переехали в новую квартиру, а окна на рапашку и комары с улицы идут стеной. Позвонили, на следующий день приехал специалист, всё померил и честно сказал, где можно сэкономить. Через неделю сетки уже стояли. Довольна.
Ольга Т.July 27, 2016 · from our order database
★☆☆☆☆
Не знаю откуда здесь столько положительных отзывов. Если бы можно было поставить 0 звёзд, я бы поставила. Самая безответственная и наглая фирма, что я когда либо встречала! Вместо 10 минут, как они пишут на их сайте Центр окон, они изготавливали 10 дней. При этом если хочешь вернуть свою предоплату из-за сорванных сроков, не вернут ни при каких условиях! Далее я можно сказать, просто выпросила, чтобы приехали мастера. В итоге когда они приехали, ни одной услуги по ремонту окон оказано не было, сорвали уплотнитель с одного окна, их не подошёл. Мастер ответил, что сложные открывания он не умеет ремонтировать, а деталь, которую менять нужно, нужно ехать покупать в Пятилеку! Так зачем тогда писать на сайте, что производите любой ремонт окон?! Но в конце менеджер требовал меня оплатить сумму, указанную в договоре! На второй день отвалился один ограничитель, который они установили, а через день выпала сетка-дверца, т.к. петли установили неправильно! Сетки натянуты неровно, насквозь торчат шурупы! На каркасе такие щели, что смысла в сетке Антипыль, просто теперь нет. Пыль летит сквозь эти щели. Вобщем зря выкинутые на ветер 90 тыс. И куча потраченных нервов! Если вдруг решитесь заказывать у этой компании какие-либо услуги, требуйте нормальный договор с живой печатью, с приложением, где будут указаны все необходимые вам услуги с ценами! Но вообще очень не рекомендую с ними связываться! Отдадите не мало денег, а в итоге всё придётся переделывать!
Юлия ШабалинаMay 26, 2026 · Review from 2GIS
★★★★★
Качественный и быстрый сервис. После ремонта окон заметно стало теплее в доме! Я очень рад, что выбрал именно эту компанию. Рекомендую всем друзьям. Надеюсь, их работа будет и дальше на таком же уровне.
Алтай КасымовSeptember 13, 2025 · Review from 2GIS