Seal
New rubber and pressure adjustment stop draughts around the sash perimeter. Replacement — from 1 000 ₸ per linear metre.


Seal
New rubber and pressure adjustment stop draughts around the sash perimeter. Replacement — from 1 000 ₸ per linear metre.

Installation seams
A damp seam loses heat; we seal it with liquid plastic inside and tape outside. From 1 500 ₸ per linear metre.

Warm reveals
A cold reveal sweats and turns black; we insulate and finish it anew. From 19 900 ₸ per linear metre.

Window sill
We close draughts from under the window sill with foaming and sealant. Work — from 15 000 ₸.

Swedish technology
We mill a groove in the frame and fit a rubber seal, so the window stops draughting. From 4 200 ₸ per linear metre.

4,9137 reviews
A window loses heat not only through the glass: the sash draughts, the seam freezes, the reveal gets cold. We close all these places.
The technician first finds where heat escapes: by hand, with a candle or a thermal imager. Then they replace worn seals, adjust sash pressure, seal installation seams, and insulate reveals and the window sill.
In Almaty windows often suffer from temperature swings: sun by day, frost by night, and the seam around the frame cracks and gets wet. Within the city, a window repair technician visits and inspects windows free of charge.

turnkey window insulation: rubber, adjustment, seams
guarantee on work and replaced components
technician visit in Almaty and window inspection
Four weak points of a window that we find most often.

Old rubber and weak pressure let air through around the perimeter, especially on a windy night.
The foam under the frame has got wet and dark, and a cold strip has appeared on the wall along the window.
An uninsulated reveal cools down, moisture collects on it, and mould starts growing in the corner.
A gap between the window sill and the wall sends a cold stream straight onto the radiator.
We do what your window needs: sometimes new rubber is enough, sometimes seams and reveals are needed.
PVC sashes

We replace the rubber around the perimeter and set the winter sash pressure.
inside and outside

We seal the foam with liquid plastic and outdoor tape so it stays dry.
cold, with mould

We insulate the reveal and apply a new finish without cold bridges.
windows letting in wind

We install a third rubber seal between the frame and the sash.
old wooden frames

Swedish technology: a rubber seal in the groove along the entire frame.
The total depends on the work your windows need; the technician will give you a quote after a free inspection.
| Type of work | Price |
|---|---|
| Turnkey window insulationseal, adjustment, seams | from 3 800₸ per window |
| Seal replacementnew EPDM rubber | from 1 000₸ per linear metre |
| Draught eliminationwe find and close the gap | from 3 500₸ per sash |
| Internal seam sealingliquid plastic | from 1 500₸ per linear metre |
| External seam sealingprotects foam from moisture | from 2 000₸ per linear metre |
| Reveal insulationinsulation and finishing | from 19 900₸ per linear metre |
| Window sill insulationfoaming and sealant | from 15 000₸ per job |
| Swedish technology for woodseal in the frame groove | from 4 200₸ per linear metre |
| Micro-lift or extra pressuresash no longer sags | from 1 700₸ per item |
| Inter-frame sealthird contour | from 2 800₸ per window |
| Thermal imaging inspectionwe find all heat leaks | from 9 000₸ per job |
| Balcony insulation from insidewalls, floor, ceiling | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Call a technicianWhat you get when you call our technician.
on work and replaced parts
the technician comes to you in Almaty and inspects the windows
we work with KBE, Rehau, VEKA, Provedal and others
fixed after inspection and does not increase
the work: cash, card or Kaspi
on WhatsApp to a photo of the problem window
daily, including weekends
consultations at Seifullina, 404, BC Kaskad
From message to a warm window sill.

Message us on WhatsApp where it's draughty or damp and send a photo: seam, reveal, sash or window sill.

The technician finds heat leaks by hand, with a candle or a thermal imager and gives you the price before starting work.

We replace the rubber, adjust the sashes, seal the seams and window sill, and insulate the reveals as agreed.

Together we check the window for draughts, show you the winter mode of the fittings, and only then do you pay.
Three orders from Almaty: where heat was escaping and what we did.
New buildIn a new build, after the house was finished, it was draughty from the window in winter, even though the frames were new and the developer hadn't adjusted the sashes.
The technician replaced the thin factory seal and set the pressure of all sashes to winter mode.
The draught is gone, you can sit by the window without a blanket.
Brick five-storey buildingIn a brick five-storey building, the installation seam under the window froze, darkened and got wet, and the wallpaper by the window peeled off.
We removed the damaged finish, dried the seam, sealed the foam with liquid plastic inside and tape outside.
The seam is dry, there's no cold strip by the window anymore.
Private houseIn a private house, the window reveals were cold and damp in winter, and black mould appeared in the corners.
We removed the old finish, treated the wall, laid insulation and installed new finished reveals.
The reveals are warm and clean, the mould doesn't come back.
Our team — makers and installers





Good to know
We handle window insulation and repair in Almaty as a direct contractor with our own team, not an agency. We start with a free inspection inside the city, diagnose whether your window can be insulated or needs replacing, then fix the seal, sashes and joints. The price is fixed in the order after measuring.
A draughty window or a wet seam does not automatically mean the whole thing has to go. The first step is a diagnosis that separates a repair job from a replacement job before anyone quotes a price.
We send a measurer who checks the gasket, the sash pressure, the double-glazed pane and the mounting joints before quoting anything. The visit and the consultation cost nothing, and the measurer comes at a time that suits you. On site the specialist runs a hand along the rubber to feel for hardening, presses the sash to test how evenly it pulls against the frame, looks for mist between the panes and probes the mounting seam for gaps. He also selects the fastening to suit the window's design and the floor level, so the fix holds on upper storeys with wind load. A unit that fails only on the rubber or the pressure usually needs repair, so the inspection should name the failing part rather than offer a blanket replacement.
Repair is enough when the frame is sound and only the gasket, pressure or joints fail; replacement makes sense when the structure itself is warped or the glazing is broken. A hardened strip, a loose hinge or a sash that no longer clamps evenly are all fixable on the existing unit. A bowed frame, a cracked pane or a sealed unit with condensation trapped inside cannot be rescued by tightening anything — the component has to be swapped. Ask the inspector to show you the failing part on the spot, because a decision made without seeing the rubber or the joint is a guess. A window insulation and repair assessment in Almaty should end with a named part and a clear next step, not a vague recommendation to change everything.
Condensation, ice and noise are symptoms rather than the fault itself, and each one points to a different part of the unit. Below is what each sign usually means and which element to check first.
Condensation on the seams usually points to a failed gasket or a cold mounting joint, not to the glass itself. Water gathers where warm room air meets a surface below the dew point, and that surface is most often the perimeter, the profile itself or the junction between the profile and the wall. Ice forms in the same spots once outdoor temperatures drop far enough, and the frost line traces exactly where the connection has opened. The glass unit is rarely the source — a fogged double-glazed pane shows moisture between the panes, while a fogged seam shows it on the room side and along the slopes. Wiping the moisture away hides the symptom but leaves the cause, so the first step is checking the seal strip and the mounting seam rather than the glass.
A draft under the sash is usually a pressure problem we fix by adjusting the hardware, while noise through the opening means the gasket or the mounting seam failed. We start with the hinges and the closing clamp: a loose leaf lets cold air slip past even when the rubber looks intact. When the seal has hardened or flattened, the draught spreads along the whole perimeter and street noise follows the same path. A draft from the slopes is a separate case — the joint has lost its tightness and needs resealing, not a new gasket. Adjusting the pressure before replacing the rubber saves the part, because a loose leaf lets air through even with a fresh seal fitted.
Plastic, aluminium, timber and panoramic frames fail in different places, so the insulation and repair work differs by material and construction. Below is what we do for each type.
| Window type | What usually fails | What we do |
|---|---|---|
| Plastic (PVC) | Gasket, sash pressure | Swap gasket, tune hardware, caulk seams |
| Aluminium | Thermal break, joints | Seal joints, check glass unit, tune sashes |
| Wooden euro | Gasket, frame gaps | Swap gasket, fill gaps, tune hardware |
Panoramic aluminium frames and glazing in new buildings both need joint work before anything else, because settlement and large panes open the gaps before the rubber gives out. On post-and-rail aluminium we seal the mounting seam along the mullions, check the thermal break and inspect the glass unit for a broken spacer, then align the sashes so they close without a draught. In a new building the frame keeps settling for the first seasons, so we caulk the joints and re-check the reveals rather than swap the whole unit at once. Where a panoramic opening stays too cold, we replace one sash with a PVC frame and keep the rest of the glazing. Sealing gaps early costs less than waiting for the rubber to tear.
The service is not a quick strip of tape over a gap. It is a sequence of steps, each with a check at the end, so you can see what was done and what was left alone.
We inspect the window, adjust the sashes, replace the worn seal, seal the mounting joints and check the glazing, and most of this fits into one visit. Sash adjustment covers the hinges and the closing pressure, so the leaf sits evenly against the profile. Joint sealing fills the seams around the mounting frame where cold air enters from the wall. Slope repair patches cracked or peeling surfaces, so moisture stops running back toward the unit. The price is fixed in the order after measuring, which keeps the visit and the invoice in step. Ask for the checklist at handover, because a step skipped quietly shows up as a draft the next cold week.
We replace the gasket on units of any manufacturer, including KBE, Rehau, VEKA and Provedal, matching the material to the profile rather than to the colour on the shelf. Each profile has its own channel depth and lip shape, and we set the sash pressure after fitting so the leaf closes without forcing. A strip that does not match the channel loses its grip within a season and starts to pull away at the corners, which is why the profile brand matters more than the shade. On older units we check the channel for deformation before ordering the material, since a bent channel will not hold even a correctly sized strip.
Timing, warranty terms and the right season to book come up before almost every order. Below is the practical detail on each point, so you can plan the visit around your own schedule.
Most insulation and repair jobs fit into a single visit, and we are open seven days a week, so winter bookings are fine. Urgent glass unit replacement is done within 24 hours. The measurer arrives at a time that suits you and takes sizes — measuring and consultation cost nothing. Cold-weather service is routine for us: sealant and joints behave predictably on a dry frame. Booking before the first cold week means seals and seams are sealed while the frame is still dry, so the gasket seats properly and holds through the frost. We reply on WhatsApp within five minutes, so a slot can be confirmed the same day you write.
| Job | Warranty | Note |
|---|---|---|
| Window repair | 1 year | Labour and replaced parts |
| Glass unit replacement | 3 years | Urgent swap within 24 hours available |
| Window installation | 5 years | Applies to installation work |
A window that drafts or fogs up rarely needs a full replacement. The practical sequence below keeps the decision grounded in diagnosis rather than guesswork.
Insulation, seal, condensation, warranty
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionFrom the inside, windows are insulated with a seal around the sash perimeter, by sealing the joints at the reveals and windowsill, and if necessary, by additional compression. The technician chooses the exact set of works after inspection to eliminate draughts and freezing.
The seal is replaced as part of the insulation if it has dried out or lost its elasticity; if it is intact, restoring the compression is enough. The technician determines the exact scope of work after inspecting the window.
It helps if the cause is draughts or freezing of the frame and joints: after eliminating cold bridges, moisture stops forming. If the issue is the double glazing itself, insulating the perimeter will only give a partial effect.
Yes, aluminium and panoramic windows are insulated, but the approach is different: the tightness of the junctions and the compression of the sashes are more important than replacing the seal around the entire perimeter. The technician selects the set of works for the specific structure.
It is possible in winter: work inside the apartment does not require above-zero temperatures outside, and external sealing is done in suitable weather. The technician will say during the inspection which works can be done immediately.
The duration depends on the condition of the window, the quality of the seal and operating conditions, so no one can give an exact figure. Usually the result lasts several seasons, and regular adjustment of the compression and care of the seal help extend it.
For window repair, we provide a 1-year warranty on work and replaced components. If draughts reappear in the area of the completed repair during this time, contact us — we will resolve it according to the warranty terms.
Сетки нормальные, к качеству претензий нет, если честно. Но с доставкой вышла накладка — привезли на день позже, пришлось переносить встречу. В остальном всё ок
Сетки на все окна поставили за один день. Мастер приехал ровно к девяти, как и обещал. После монтажа на подоконниках ни пыли, ни стружки — вот это удивило больше всего
Долго откладывал это дело, казалось мелочью, которую можно сделать потом. В итоге к августу в квартире стало невозможно спать: окна закрыты, духота, кондиционера нет. Позвонил в понедельник, во вторник утром у меня уже были замерщики с рулеткой и лазерным уровнем. Объяснили разницу между рамной и раздвижной, посоветовали на кухню обычную, а на балкон раздвижную, чтобы удобнее выходить. Монтаж занял часа три на четыре окна. Ребята приехали со своим инструментом, после себя всё убрали, даже пропылесосили. Сейчас открываю балкон одной рукой и никакой живности в доме. Жалею только, что не сделал этого раньше.
Сделали на дачу в пригороде, куда летом приезжают внуки — комары их просто едят. Приехали вобщем вовремя всё поставили, ещё и старую сетку сняли бесплатно. Спасибо
Понравилось, что всё объяснили простыми словами и не навязывали лишнего. Замер сделали быстро, сроки выдержали, установили аккуратно. Ничего не продувает, открывается нормально.
Менял окна в квартире. Замерщик приехал вовремя, всё объяснил по профилю и стеклопакету. Монтаж сделали аккуратно: створки работают плавно, откосы ровные, нигде не продувает. После установки дома стало заметно тише и теплее
Меняли старые деревянные окна на пластиковые. Установили ровно, не дует. Работали один день, мусор убрали. Цена как в договоре. Все хорошо, рекомендую
Брал услуги по утеплению окон этой компании. Результат превзошел все ожидания, теперь в квартире тепло и уютно. Мастера вежливые, внимательно относятся к клиентам. Постарались уложиться в сроки, хочу отметить это.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp