Sash adjustment
Simple adjustment without removal — from 3 000 ₸ per sash. With removal — from 4 000 ₸.


Sash adjustment
Simple adjustment without removal — from 3 000 ₸ per sash. With removal — from 4 000 ₸.

Hardware repair
Restoring mechanism operation — from 7 800 ₸ per job. Set replacement — from 10 000 ₸.

Handle replacement
Standard or lockable — from 2 750 ₸ per unit. We'll match it to your profile.

Seal
Seal adjustment and replacement — from 1 250 ₸. Ask the technician for the full list.

Hinge replacement
For wear or sagging — from 4 750 ₸ per unit. Hinge adjustment — from 3 000 ₸.

5,010 reviews
Restoring the operation of the sash, hardware and seal without replacing the entire window
A PVC window consists of a frame, sash, hardware, seal and double glazing. Repair affects moving parts: hinges, scissors, handle, cams and the seal contour. Double glazing is replaced separately if it cracks or loses its seal.
Restoring the sash without replacing the window preserves the frame and double glazing; only worn parts are replaced. During inspection, the technician checks hinges, cams, scissors, blocker and seal. Measuring is needed to select compatible hinges, handles and seal contour by sash size.

warranty on repair and replaced components
daily, including weekends
measuring visit and consultation before work
Six typical plastic window faults and what is done about them on site

The mechanism is jammed due to wear or dirt. The technician disassembles the unit and restores movement or replaces the set.
The tilt-and-turn mechanism's blocker has failed. The blocker and scissors are repaired, restoring the correct operation.
The scissors are responsible for tilting the sash. If broken, they are replaced with ones compatible with the profile.
The hinges have sagged under the weight of the double glazing. Adjusting the hinges returns the sash to a level position in the frame.
The compression has loosened or the seal has worn out. The technician adjusts the compression and replaces the seal if necessary.
The handle has cracked or spins. It is replaced with a standard or lockable one to suit your profile.
Five areas of work to restore a plastic window without replacing the frame
Compression and hinges

Adjusting the movement of the sash and balcony door, eliminating catching and draughts.
Set per sash

Complete replacement of the mechanism if repairing individual components does not help.
Small parts

Replacement of the handle, hinges and pins when worn or broken.
Compression contour

Replacement of the seal in windows of any manufacturer, including KBE, Rehau, VEKA.
Changing the scheme

Converting a fixed window into an opening or tilt-and-turn sash.
Price list for window restoration work; the final amount is fixed in the order after measuring
| Type of work | Price |
|---|---|
| Simple sash adjustmentbasic adjustment without removal | from 3 000₸ per sash |
| Sash adjustment with removalcomplex adjustment with sash removal | from 4 000₸ per sash |
| Balcony door adjustmentsetting the seal and hinges | from 6 000₸ per unit |
| Hardware repairrestoring the mechanism operation | from 7 800₸ per job |
| Hardware replacement on sashfull set replacement | from 10 000₸ per sash |
| Replacement of scissors or corner switchwhen the opening mechanism breaks | from 5 500₸ per unit |
| Replacement of cam or strike platesmall seal parts | from 1 300₸ per unit |
| Hinge replacementfor wear or sagging | from 4 750₸ per unit |
| Window handle replacementstandard or lockable | from 2 750₸ per unit |
| Conversion to tilt-and-turn openingchanging the opening pattern | from 19 000₸ per sash |
| Conversion of fixed window to openingcutting the sash into the frame | from 28 000₸ per sash |
| Installation of micro-lift or extra sealadditional hardware | from 1 700₸ per unit |
| Installation of balcony latchlatch installation | from 3 750₸ per unit |
| Unlocking a jammed sashif the sash is stuck | from 2 400₸ per sash |
| Cleaning and lubrication of hardwaremechanism maintenance | from 1 250₸ per sash |
In addition to work, the estimate includes parts, fixings and seal if replacement is requiredThe total depends on the number of sashes: each sash is counted separatelyThe price is fixed in the order after measuringMeasuring and consultation are free
Check the cost of workTerms of work for restoring plastic windows in Astana
for work and replaced components
for window installation work
for double glazing replacement
we accept requests on weekends too
in Astana and Almaty
after installation: cash, card or Kaspi
with a list of replaced parts
you can order the service in 17 cities of Kazakhstan
Four steps from request to checking the work

You write on WhatsApp — we reply within 5 minutes, clarify the problem and a convenient time.

The technician inspects the window, checks the sash and compression, and provides a list of work and the cost.

Adjustment or replacement of parts is carried out at your home; parts are selected to match the profile.

We check the movement of the sash and compression, show the result, and complete the documents.
Three requests for plastic window repair and what was done on site
Nine-storey panel buildingThe handle doesn't turn, the sash is jammed. The windows are installed in a panel building, the mechanism has not been serviced for a long time.
The technician disassembled the unit, cleaned and restored the hardware movement. Checked the sash operation in both modes.
The sash opens and closes smoothly, and the handle turns without effort.
New build after handoverThe sash opened in two modes at once after the building was handed over. It was not possible to close the window in the usual way.
We repaired the blocker and scissors and restored the correct sash opening pattern.
The window again works in turn and tilt modes separately.
Brick five-storey buildingThe hardware scissors broke: the sash stopped fixing in the tilt position.
We replaced the scissors with ones compatible with the profile and adjusted the sash pressure.
The sash tilts and fixes, and the pressure is restored around the entire perimeter.
Good to know
Centre Okon handles pvc window repair in Astana with its own fitters, not through an agency. We start with a free measuring visit, fix the price in the order after it, and you pay only once the work is done. Repair carries a one-year warranty on labour and replaced parts.
Repair is more than tightening a loose handle. It covers adjustment, seal replacement, hardware work and glass unit swaps, and it stops where a damaged profile makes replacement the only sensible option.
We adjust the sash across three planes first, and only move to new hardware when the mechanism itself is worn out. A dropped leaf sits unevenly in the frame, so the top hinge pulls away and the closing edge no longer meets the seal evenly. Turning the adjustment screws on the hinges brings the leaf back into square, restores pressure along that edge and closes the gap that lets cold air through. Handles, locking cams and tilt-and-turn mechanisms are checked in the same visit, and only the parts that have actually failed get replaced. A handle that turns hard is often a sign of a dropped leaf rather than a broken lock, so adjusting before replacing saves the part. We back window repair with a one-year warranty on labour and replaced parts.
A sound frame and a working leaf almost always justify repair, while a cracked profile or a failed structural seal points to replacement. Repair makes sense when the frame is intact, the reinforcement inside the profile is not corroded and the leaf still closes against it. What fails first is usually the movable part or the sealed glass: the gasket flattens, the hardware wears, the unit loses its gas fill. A glass unit is swapped without touching the frame, so fogging between the panes alone never means a new window. Replacement becomes the honest answer when the profile itself is cracked, when the frame has lost its shape after a water leak, or when the wall joint has opened and no adjustment holds the leaf straight. We measure the opening before advising either way, and the measurer tells you plainly which of the two your window falls into.
Every window complaint points to a likely cause, and the cause decides the work. Below we line up symptoms, probable reasons and what we do about each, so you can match your own situation.
| Symptom | Likely cause | What we do |
|---|---|---|
| Draught along the sash edge | Compressed or hardened seal | Replace the seal, reset the pressure |
| Fogging inside the glass unit | Sealed cavity has failed | Swap the glass unit |
| Fogging on the room-side glass | Normal indoor humidity | Ventilate, no repair needed |
| Sash will not close or scrapes | Dropped sash geometry | Adjust hinges and the sash |
| Cold edge on the sash | Broken mounting seam | Reseal the frame-to-wall joint |
A draught that returns usually means the gasket was replaced but the sash geometry was never corrected. A leaf that has dropped a few millimetres along the hinges no longer presses evenly, so even a fresh gasket leaves a gap on one side. In our practice we start with diagnostics of the whole window rather than the seal alone — checking the pressure, the sash alignment and the hardware before touching anything. When you need pvc window repair astana, this full check of the whole window is where the work begins. We check the frame-to-wall joint as well, since a cold edge on the sash often comes from the mounting seam rather than the seal. That is why getting the geometry right the first time saves a repeat visit.
Rubber strips and moving parts wear out before anything else on a window. Below is how to tell a tired strip from a dirty one, and how to keep the fittings working smoothly between visits.
We replace the rubber when it has lost elasticity or gone hard, and simply clean and treat it when it is still soft but dirty. Run a finger along the strip: a healthy length springs back and feels slightly tacky, while a worn piece stays flattened, cracks at the corners or leaves a grey line on your hand. Hardened material no longer presses against the sash, so the draught returns even after the fittings are tightened. We fit new strips on windows from any maker, including KBE, Rehau, VEKA and Provedal, so the profile brand never blocks a repair. A damp wipe and a suitable care product twice a year keep a soft strip supple far longer.
This section walks through the whole path of a pvc window repair astana visit, from your first WhatsApp message to the moment you accept the finished work, so you know what happens at each step and when money changes hands.
We reply on WhatsApp within five minutes, book a free visit at a time that suits you, and fix the price once the specialist has seen the window. That person checks the profile, the fittings and the mounting seam rather than just the draught you noticed, so the fixed price reflects the real cause instead of the visible symptom. The survey and consultation cost nothing, and this is the point where the mesh, fasteners and frame colour get chosen with you in the room. In our practice the locked-in figure is what stops the awkward conversation later — nobody wants a number that drifts once the crew is already on site. What you sign reflects the actual window, not an estimate taken over the phone.
We agree the scope before any tool comes out, carry out the work with our own crew, and hand over the result together with you before payment is made. On the day, the technician confirms what will be replaced and works through the adjustment, seal or hardware the survey identified. When the job is done you check the sash travel, the seal contact and the closing action yourself, and only then does payment happen — cash, card or Kaspi, your choice. That sequence keeps the risk on our side until the window is inspected and accepted, which is how we prefer it. If something does not feel right at handover, say so on the spot — it is far easier to correct while the technician is still there than to book a second trip.
Timing and warranty are the two things most people check before booking any work. This section shows how long a repair takes, what the urgent option involves and what each type of cover actually includes.
Most repairs finish in a single visit, and a replacement glass unit can be made and fitted within one day for an urgent case. A standard visit covers adjustment, seal replacement and hardware fixes on the spot, while a fogged or cracked pane needs a fresh sealed unit cut to size first. We handle urgent production and replacement within a single day, with a surcharge added to the price of the new glazing. The new unit is fitted into the existing frame, so the rest of the window stays as it was. That surcharge applies to the glazing itself, so it is worth flagging the deadline when you first message us.
| Work | Warranty | What it covers |
|---|---|---|
| Window repair | 1 year | Labour and replaced parts |
| Glass unit replacement | 3 years | The new sealed unit and its fitting |
| Window installation | 5 years | Full installation work |
A few practical points decide whether a window repair holds up or quietly fails again within weeks. Here is what is worth keeping in mind.
Reviews, adjustment, double glazing replacement, winter repair
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionLook at reviews on maps and platforms where people describe similar faults and how the company handled the request. Pay attention to whether the technician came back and how warranty obligations were met.
At home you can tighten the pressure with an Allen key and lubricate the hardware, but without experience it is easy to knock the settings off and make the misalignment worse. If the sash has sagged or sticks, it is better to show the window to a technician.
Yes, if the frame is intact and the hardware works, only the double glazing is replaced — this is faster and more sensible than touching the whole window. The technician will take measurements and select a suitable option; the warranty on double glazing replacement is three years.
Most work can be done in the cold as well. The technician will say after inspecting the window what can be done straight away and what is better left until it is warmer.
Besides the seal, the technician adjusts the sash, checks and repairs the hardware, and if necessary replaces the handle, hinges or cams. The exact set of works is determined after inspection, because the cause of draughts or sticking is different for each window.
Отрегулировали и поменяли резину на двух окнах, все хорошо, теперь не дует, окна очень плотно закрываются, сделали быстро, спасибо
Приехали сразу и заменили ручки спасибо большое я довольна
Ответственные, пунктуальные и приятные в общении специалисты. Все договорённости соблюдены, работа выполнена аккуратно и в срок. Очень приятно иметь дело с людьми, которые ценят время клиентов и добросовестно относятся к своему делу. Вы молодцы! Спасибо вам большое 🤍
Пишу отзыв по истечении более 10 дней после замены оконных " запчастей". Работа аккуратная. Мастер Батырхан после себя убрал, показал конечный результат, заменил старые части окна на новые. Главное, теперь с окон не дует и в комнатах тепло. Обращайтесь в Центр Окон, если важно соотношение Качества и Цены. Благодарю Вас, Батырхан.
Всем привет ребята выполняют свою работу на отлично
Отличный мастер, быстро чётко аккуратно всё сделал, цены демократичные, спасибо!
Все супер, быстро и четко, цены радуют, устанавливали в подъезде окна, 👍👍
благодарю за выполненную работу, быстро и качественно.
Спасибо мастеру Батырхан. Мастер своего дела. Все сделали быстро и качественно. Всем советую
Хочу выразить благодарность мастеру Батырхану за качественную работу! Приехал вовремя, быстро определил причину проблемы и профессионально выполнил ремонт окон. Всё сделал аккуратно, все объяснил, ответил на вопросы. Видно, что человек знает своё дело и ответственно относится к работе. Осталась очень довольна результатом! Рекомендую как грамотного и добросовестного специалиста.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp