Swedish technology
Rubber in the frame groove makes an old window tight and doesn't stop it opening. From 4 200 ₸ per linear m.


Swedish technology
Rubber in the frame groove makes an old window tight and doesn't stop it opening. From 4 200 ₸ per linear m.

Seam under the sill
Through the open seam under the sill, the snowstorm blows in snow and cold. We seal from 2 000 ₸ per linear m.

Loggia from inside
We insulate the sashes and walls of the loggia so cold doesn't reach the room. From 6 800 ₸ per m².

Rubber and compression
New seal and winter mode on the sash stop draughts. From 1 000 ₸ per linear m.

Thermal camera
Shows all cold spots in the window before work starts. Inspection — from 9 000 ₸.

4,49 reviews
Minus thirty and strong wind outside quickly find every gap. Better to close them before the draught starts.
Cold gets in through cracked wooden frames, open seams under the sill, loose loggia sashes and thin double glazing. The technician checks the whole window and closes exactly the places where heat escapes.
Winters in Astana are long, with snowstorms and strong wind, so windows here work at their limit. We take requests for inspection daily from 09:00 to 22:00, and the technician will come at a convenient time.

comprehensive work on one window
warranty on work and components
we take requests daily in Astana
Four weak spots that technicians find in Astana.

Gaps between the sash and frame of an old wooden window let frosty air through.
Outside under the sill there is an open seam, and the snowstorm blows snow into it.
Balcony sashes close with a gap, and cold goes into the room.
Thin glass freezes at the edges and gets covered with frost.
We choose the solution for the window: Swedish technology for wood, rubber and seams for PVC, sashes and walls from inside for the loggia.
wooden frames

We mill a groove and lay rubber around the entire sash perimeter.
outer seam

We seal the seam under the sill from snow, wind and meltwater.
walls, floor, ceiling

We insulate the loggia from inside so it doesn't cool the room.
windows against wind

Third rubber contour between frame and sash.
gap below

We foam voids and seal the seam under the window sill.
The price depends on the type of window and what needs to be covered; the technician will give you a quote during the inspection.
| Type of work | Price |
|---|---|
| Insulating one windowrubber, seams, compression | from 3 800₸ per window |
| Perimeter sealsoft rubber | from 1 000₸ per linear m |
| Stop draughtstargeted at gaps | from 3 500₸ per sash |
| Inner seamliquid plastic | from 1 500₸ per linear m |
| Outer seam and sillexterior sealant | from 2 000₸ per linear m |
| Reveal with insulationturnkey | from 19 900₸ per linear m |
| Window sillfoaming and seam | from 15 000₸ per job |
| Swedish-style wooden framemilling and rubber | from 4 200₸ per linear m |
| Extra compressionfor long sashes | from 1 700₸ per item |
| Third rubber contourbetween frames | from 2 800₸ per window |
| Thermal imaging checkall heat leaks | from 9 000₸ per job |
| Loggia insulation from insidewalls, floor, ceiling | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Book an inspectionA quick look at how we work.
on work and replaced parts
we take requests in Astana daily
we insulate old and new windows
fixed after inspection
work: cash, card, Kaspi
on WhatsApp for a photo of the window
technicians work on weekends too
we work across Kazakhstan
Four steps to a warm winter.

Send a photo of the window via WhatsApp and tell us where it's cold: frame, sill, loggia or glass.

The technician checks the window by hand, with a candle or a thermal imager and gives you the cost of work.

We seal seams and sills, install rubber in wood or PVC, adjust loggia sashes.

We check the window for draughts and show you the winter mode, after that you pay.
Three orders from Astana.
Kitchen with gas stoveIn the kitchen with a gas stove there was an old wooden window, and in frost cold air blew from the gaps right onto the stove.
The technician milled a groove in the sashes and installed a rubber seal using Swedish technology.
The window no longer lets in draughts and opens easily for ventilation.
Corner apartmentIn a corner apartment on the windy side during a snowstorm, snow blew under the sill and it was cold under the frame.
We sealed the seam under the sill outside and closed the inner seam with liquid plastic.
Snow no longer gets under the sill, it's warm under the frame.
New buildingIn a new building after the house was commissioned, a heater ran by the window in the bedroom all winter.
We did a complex job: rubber, adjustment, seams with liquid plastic and foaming under the window sill.
The heater is no longer needed, the bedroom is warm.
Good to know
For window insulation in Astana, we start with a free measuring visit: the measurer finds where the cold gets in, checks the seal and the sash pressure, and helps choose between a new seal, hardware adjustment or a glass unit replacement. The price is fixed after measuring, and we give a one-year warranty on window repair.
Draughts almost always come from one of four zones — the sash, the mounting seam around the frame, the slopes, or the joint under the sill and drip edge. Before changing anything, a fitter finds the zone.
We treat condensation on the glass and frost in the corners as a sign of a cold bridge or a failed glass unit, not as a draught, so the fix differs from sealing a gap. A wet corner that stays wet after the gasket is replaced usually points to the mounting seam or the glass unit itself. Floor level and the side of the building change how fast that shows up — north-facing top-floor rooms frost over first. Insulation work in Astana has to answer that question before any work starts, because sealing a gap will not stop a cold bridge. Window insulation Astana jobs start with this same check, since a cold bridge and a draught call for different repairs. A measurer checks the glass unit and the seam on site, and that visit costs nothing.
The gasket and the sash pressure are the two most common reasons a window lets cold air through, and both can be fixed without replacing the unit. Here is what to change and in what order.
We fit chambered seals that stay elastic in deep frost, and we replace the gasket on units of any manufacturer, including KBE, Rehau, VEKA and Provedal profiles. A chambered profile keeps several air pockets along its length, so the rubber compresses evenly against the frame instead of hardening into a single flat strip. Cheaper PVC strips stiffen faster in the cold and start to gap at the corners, which is where most draughts begin. On older wooden sashes we sometimes find the strip compressed to half its thickness and no longer touching the frame at all. A gasket that has gone hard and shiny no longer springs back when you press it, and that loss of rebound, not the visible crack, is what lets the chill through.
We adjust the sash pressure as part of the insulation visit, and winter mode is a real hardware setting that pulls the leaf tighter to the frame, not a myth. On most tilt-and-turn fittings the adjustment sits under a small cap on the hinge side, and a short turn of the eccentrics moves the leaf a millimetre or two closer. That gap matters: a two-millimetre opening along a full-height edge passes more air than most people expect. The setting is worth checking on any leaf untouched since installation, because factory settings are deliberately loose to protect the rubber during transport. Turning the pressure up too far for the whole year flattens the gasket early, so revisit the setting when the season changes rather than leaving it cranked shut.
| Symptom | Part to check | Work it calls for |
|---|---|---|
| Draught along the sash edge | Seal | Seal replacement |
| Sash loose, handle hard to turn | Hardware | Pressure adjustment |
| Cold strip around the frame | Mounting seam | Seam sealing |
| Wet corner, frost on glass | Glass unit | Glass unit replacement |
Not every cold window needs replacing whole, and not every draught is cured by a new seal. The line between the two runs through the frame, the seam and the pane itself.
We can make and replace a glass unit within one day when frost is already inside, and that urgent route carries a surcharge on the pane itself. The visit covers removal of the failed pane, fitting the new one and resealing the rebate. A unit that has lost its tightness fogs between the panes, and no amount of seam sealing brings the clarity back. That is why the fast route is worth planning before minus thirty settles in — once condensation freezes at the edge, a standard order turns into weeks of wiping sills every morning. A fogged unit also hides the frame behind a film of moisture, so the seam and the slopes go unchecked while the glass stays misted.
The job follows a short chain: measure, pick the parts, install, check. At every step the client sees what is happening and what is being paid for.
We reply on WhatsApp within five minutes, the measurer comes at a time that suits you, and the price is fixed in the order after measuring, with payment after installation by cash, card or Kaspi. The visit and the consultation cost nothing, and they cover the whole decision — dimensions, sealing, hardware, fastenings. Our measurer reads the profile and the floor of the flat before anything is ordered, so the parts are chosen for that particular opening rather than pulled from a standard kit. A gasket that fits one casement can be useless on another, and the same goes for hinges and locking points. Because the measurement happens first, the order lists exactly what will go in, and the figure on it does not move afterwards.
At handover we check the sash pressure, run a hand along the joint and the slopes, and confirm the gasket sits evenly, and the unit does not have to come out for any of this. Warm air leaking past a closing casement usually means the hardware needs a turn, not a new unit. The installation joint and the slopes take the hardest hit in an Astana winter, so we look at both before signing anything off. Insulation is a one-time job on a sound frame, so if a draught returns the next season it points to a part that was not the real source, not to work that needs repeating every year.
Plastic is not the only type in the capital, and wood, aluminium and awkward openings call for different details rather than a different principle. The method stays the same; the hardware and the seal change with the frame.
We insulate plastic, wooden and aluminium frames, and the difference sits in the gasket and the hardware rather than in the approach, since the strip is replaced on units of any manufacturer. On plastic frames the sash pressure is set with the trunnions, and a worn loop seal is swapped for a new one without touching the profile. On aluminium the thermal break and the slim frame leave less room for a thick seal, so the fit has to be exact. Wooden frames move with the seasons more than plastic ones, so the seal and the pressure setting on wood are worth checking earlier in the cold season — we look at them first when a wooden unit starts to whistle.
We also insulate the glazing of loggias, gazebos and verandas, where the frame is often thinner and the wind load higher than on a flat unit. A loggia sash takes the same loop seal and hardware as a room unit, but the glazing bead and the seam to the parapet need a closer look, because that joint faces the street. On gazebos and verandas the structure may be light aluminium with single glazing, and the weak point is the mounting seam rather than the glass. An open-sided structure loses heat faster than a flat, so the seam and the pressure setting matter more there than the choice of gasket alone. We check that seam before quoting, since it decides whether sealing alone will hold through the winter.
Cold air in an Astana flat usually has an identifiable origin, and the sections above narrow it down to a gasket, a pressure setting or the glass itself. The short list below sums up what to check before booking anything.
Window insulation, materials, seals, freezing
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionFirst, find where the draft comes from: most often it's a worn seal, loose sash pressure, or seams under the sill. Replacing the rubber with a frost-resistant one, adjusting the hardware, and sealing the seams help. The exact set depends on the window and will be shown by an inspection.
For plastic windows, a frost-resistant seal, pressure adjustment, and professional foam for seams are used. If the reveals freeze, adding reveal insulation helps. The best option is chosen after checking where exactly heat is lost.
From the outside, the installation seam under the sill is insulated and the junctions are foamed so that cold doesn't come through the cavities. It's important not to foam the drainage holes, otherwise the window will start to fog up. The work is done from the street following the technology.
Most often the cause is not the rubber but drafts from the installation seams or hardware that doesn't press the sash. Sometimes cold air comes through hidden cavities in the profile. A thermal imager during inspection will show the exact zone.
If ice and condensation form along the sash edge near the rubber while the centre of the glass stays clear, the seal or the pressure is to blame. If the whole unit or the space between the panes freezes, the problem is the double glazing itself.
In extreme frosts, frost-resistant seals based on EPDM and silicone, as well as professional foam with a low expansion coefficient, perform well. Ordinary foam rubber or cheap rubber stiffens and cracks in the cold. The specific set depends on the window and the condition of the seams.
Отрегулировали и поменяли резину на двух окнах, все хорошо, теперь не дует, окна очень плотно закрываются, сделали быстро, спасибо
Пишу отзыв по истечении более 10 дней после замены оконных " запчастей". Работа аккуратная. Мастер Батырхан после себя убрал, показал конечный результат, заменил старые части окна на новые. Главное, теперь с окон не дует и в комнатах тепло. Обращайтесь в Центр Окон, если важно соотношение Качества и Цены. Благодарю Вас, Батырхан.
Спасибо мастерам за работу! Поменяли резину, обработали силиконом, всё объяснили и проконсультировали. Теперь ждём зиму, чтобы проверить, будут ли окна продувать.
«Хочу выразить огромную благодарность вашим мастерам за профессиональный ремонт наших окон. Окна стали плохо закрываться и продували, в доме было прохладно. Мастер приехал вовремя, быстро нашёл причину, заменил изношенные уплотнители и отрегулировал фурнитуру. Окна открываются и закрываются идеально. Рекомендую всем!»
Заказывал москитную сетку! Ребят сразу в этот же день приехали оперативно, снял замеры, качество сетки радует анти мошка топ, Легко снимается и легко вставляется без всяких заморезов ничего не надо крутить, снял поставил одним словом!!!!
Обратились по рекомендации от соседей в чате. От всей души благодарим Батырхана и Дмитрия за проделанную работу и тепло в нашем доме. У нас жк бизнес класса, но застройщик изначально сделал очень плохие окна витраж, которые продували:( как настали холода, похолодало и у нас дома. Ребята оперативно приехали, провели консультацию и через несколько дней сделали всё, что необходимо. Спасибо за ваш подход и заботу, вы сделали всё на максимум. Обязательно еще обратимся, тк нужно будет в ближайшем будущем ставить и сетки, и дет защиты и прочее
Доброе утро. Ничего не изменилось, как дуло , так и дует. Если знали, что ничего не изменится, для чего делали работу и взяли оплату, Короче ИБД….
Спасибо ребятам из Центра окон. Сильно продували окна, дома тянул сквозняк. Приехали, проконсультировали, назначили дату ремонта. Потребовалось заменить фурнитуру на окне от застройщика и заменить резинки на одном окне, на втором регулировка и также замена резинок. Дома стало теплее и менее зябко. Благодарю. Из пожеланий - было бы здорово если рабочая команда приводила после себя пространство в порядок, забирала бы на переработку может быть или металлолом старую фурнитуру. В остальном ок.
Ребята молодцы, окна отрегулировали, профессионалы своего дела, быстро поняли суть проблемы продувания, устранили👌🏻
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp