Technician holding a loop of new rubber window seal in a children's room
from 1 000 ₸ per linear mWe replace the seal from inside the apartment in one visit, without removing the window; 1-year warranty on the work.Calculate

Window Seal Replacement in Astana

PVC windows · Apartment

EPDM rubber

The most common option: an elastic contour holds the sash tight again and keeps the wind out even in frost. From 1 000 ₸ per linear m.

Technician holds a coil of black rubber window seal
GoogleYandex MapsZoon

4,98 reviews

What a fresh seal contour gives your window

A live seal keeps heat better than any adjustment. We replace it without touching the frame, double glazing or hardware.

How it works

Every PVC window has two or three rubber contours: on the frame, on the sash and sometimes between them. While the rubber is elastic, the sash fits tightly without gaps. A hardened contour no longer springs back, and icy wind finds a gap along the perimeter.

Frost and strong wind in Astana quickly show where the seal has failed: ice in the corners, a draught by the windowsill, whistling in the sash. The technician installs a new seal for your profile and adjusts the pressure.

Hand fits a new black seal into the groove of a white sash
from 1 000 ₸

linear metre of new seal with installation

1 year

warranty on work and replaced components

09:00–22:00

we take requests in Astana every day

Types
VEKAKBERehauProvedalOther

How seal replacement in Astana is performed

Four problems that most often bring people to us in the cold season.

A palm at the edge of a closed sash checks where the draft comes from
  • 01Rubber has hardened

    The old seal feels like plastic and does not yield to a finger — the sash no longer fits tightly.

  • 02Small cracks

    Cracks in the sash corners widen in frost and turn into gaps that let cold in.

  • 03A piece has fallen out of the groove

    If the seal has popped out, it leaves a through gap; it is better to install a new solid contour.

  • 04Draught along the perimeter

    A burning candle by a closed sash flickers where the seal does not hold.

Types of seal contours for windows in Astana

The choice depends on the window and location: a loggia needs a durable door contour, while a window on the windy side needs a frost-resistant one.

EPDM

PVC windows in an apartment

Technician holds a coil of black rubber window seal

Elastic rubber for most profiles, does not lose shape from heat or cold.

from 1 000 ₸/linear m

Premium

windward side of the house

A craftsman holds a coil of grey rubber window seal in his hand

German seal stays flexible in severe frost and keeps a tight fit longer.

from 1 200 ₸/linear m

Door

balcony, loggia

A craftsman holds a strip of brush window seal with bristles in his hand

Durable rubber for a door that opens many times a day.

from 5 000 ₸/pc.

Brush

aluminium sliding

A length of black self-adhesive window seal on a master's palm, white backing paper peeled back at the end

New dense pile closes the gap at the runners against wind and snow dust.

from 1 150 ₸/linear m

Between frames

windows facing the avenue

A craftsman holds a thin strip of double-glazed window seal in his hand

A third contour between sash and frame dampens noise and stops drafts from below.

from 2 800 ₸/window

Window seal replacement prices in Astana

The total depends on contour length, seal type and number of sashes; we will give the exact price after inspection.

Type of workPrice
EPDM seallabour and materialfrom 1 000₸ per linear m
Premium rubber from Germanyhandles frost betterfrom 1 200₸ per linear m
Window turnkeyboth sash contoursfrom 3 500₸ per window
Balcony door completedoor and frame rubberfrom 5 000₸ per item
Aluminium brush contourfor sliding framesfrom 1 150₸ per linear m
Rubber maintenancecleaning and siliconefrom 750₸ per linear m
Third contour between framesagainst noise and coldfrom 2 800₸ per window
Draught eliminationwe close the gapfrom 3 500₸ per sash
Pressure adjustmentwinter modefrom 3 000₸ per sash
Liquid plastic along seamsframe and glazing bead jointsfrom 1 500₸ per linear m
Insulation of old wooden frameSwedish methodfrom 4 200₸ per linear m

Price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi

Book an inspection

Why customers order seal replacement in Astana from us

What stands behind the work of our technicians.

Warranty1 year

on labour and new seal, terms in the order

Hours09:00–22:00

we take requests in Astana daily

Profilesany

KBE, Rehau, VEKA, Provedal and other manufacturers

Pricefixed

after inspection, and it does not change during work

Paymentafter

checking the window: cash, card or Kaspi

Response5 minutes

on WhatsApp to a photo and description of the problem

Scheduleno days off

technicians work on Saturday and Sunday

Experiencesince 2012

we work across Kazakhstan

How seal replacement on plastic windows works at your home

Four steps, and your flat is quiet and warm again.

  1. A hand holds a phone with a dark screen near the edge of a white window
    015 minute response

    Request

    Take a photo of the window and write on WhatsApp what bothers you: ice, draft, whistling or a fallen seal.

  2. A tape measure lies along the bottom edge of the window opening, close-up view
    02at a convenient time

    Inspection

    The technician checks contours, hardware and pressure, identifies the profile and gives the price before work starts.

  3. Hands holding a piece of new black window seal above a workbench with tools
    03one visit

    Replacement

    We remove the old rubber, clean the grooves and install a new seal in one piece, without breaks at the corners.

  4. Finished white window in a bright room
    04together with you

    Check

    We adjust the sash pressure for winter, test the window with a strip of paper, and only then do you pay.

Seal replacement order stories in Astana

Three orders from Astana: what the issue was and what we did.

Closed balcony door in winter: slippers on the mat at the threshold, snowy yard behind the glassPanel nine-storey building
Object
flat
Windows
installed long ago
Where
balcony door
Work
new contour
Price
from 5 000 ₸/pc.
After
warm floor by door
  1. Request

    In a panel nine-storey building, cold came through the balcony door in frost, and feet froze at the loggia threshold.

  2. What we did

    We replaced the rubber of the door and frame around the entire perimeter and adjusted the sash pressure to winter mode.

  3. Result

    The balcony door no longer lets in drafts, the floor at the threshold is warm.

I want the same
Window in a new building after renovation, a paint roller in a tray on the floorNew building
Object
flat
Building
new building
Was
seal in paint
Work
replacement
Rubber
EPDM
After
windows close tightly
  1. Request

    In a new building after renovation, the seal on the windows was painted over together with the reveals, and the sashes started letting in cold.

  2. What we did

    The technician removed the painted contours, cleaned the grooves and installed new rubber on the frame and sashes of all windows.

  3. Result

    The windows close tightly, cold does not pass through the sashes.

I want the same
Window in a brick building in winter, with a snowy courtyard and a similar brick building outsideBrick five-storey building
Object
flat
Building
brick
Was
ice
Work
replacement
Rubber
premium
Price
from 1 200 ₸/linear m
  1. Request

    In a brick five-storey building in severe frost, the sash froze to the frame, and ice grew in the corners.

  2. What we did

    We installed a German frost-resistant seal and tightened the pressure so the sash fits without a gap.

  3. Result

    No ice, the sash opens even on the coldest days.

I want the same

Good to know

Window Seal Replacement in Astana

We handle window seal replacement in Astana with our own fitters, not through middlemen. We replace seals on windows from any manufacturer, including KBE, Rehau, VEKA and Provedal, and back the work with a one-year warranty on labour and replaced parts. Measuring and consultation are free, and you pay only after installation.

How to Tell Your Window Seal Needs Window Seal Replacement

A seal wears out quietly, yet several everyday signals reveal its condition without any tools. Here is what points to the seal itself — and what actually belongs to the hardware.

Signs that the seal is worn out

A worn seal shows up as a draught along the sash edge, cold glass near the frame in winter, and condensation collecting on the inner rebate rather than on the glass itself. The rubber profile that once pressed tight against the frame flattens into a thin strip, so the gap it used to fill opens by a millimetre or two — enough for street air to slip through on a windy day. Moisture follows the same path: warm indoor air meets the cold rebate and settles there, which is why the sill and corners stay damp while the pane looks dry. Run a hand over the closed leaf on a windy day — an even draught down the whole edge points to the seal, while a draught concentrated at one corner usually means the hinge side and the sash pressure instead.

How long a seal lasts and when to replace it

  • Hardening: the seal feels stiff and no longer springs back when you press it.
  • Flattening: a permanent dent stays where the leaf presses on the seal.
  • Cracks: small splits appear along the fold, most often on the sunny side.
  • Draught: air moves past the closed leaf even when the handle is fully turned.
  • Condensation: moisture collects on the inner rebate rather than on the glass.
  • Age: past several seasons in a cold climate, the seal is worth checking even if it looks fine.

Choosing the Right Window Seal Replacement for Astana Winters

The seal material decides how long the gasket stays elastic through frost and temperature swings. Below we compare the main types and show where each one belongs on a window.

Seal materials compared

Four gasket materials by cold and weather behaviour
Seal typeCold flexibilityUV and weather resistanceTypical use
RubberModerateModerateStandard sashes
EPDMGoodHighExposed frames, long service
TPEGoodGoodCombined rubber-plastic feel
SiliconeHighHighVery cold or sunny sides

Seal on the sash, the frame and the impost

We replace the seal on the sash, the frame and the impost as separate runs, because each sits in its own groove and wears at a different rate. A sash gasket runs the full perimeter of the opening leaf, the frame gasket lines the fixed profile, and the impost gasket closes the vertical bar between the two sashes. On PVC systems from KBE, Rehau, VEKA and Provedal the groove profile differs, so the cord is matched to the channel rather than cut to a single universal width. The sash gasket usually wears fastest since it compresses on every close, so a full replacement that skips the frame groove often leaves a draught that returns within a season. When we order the cord, we take the groove width and depth from the profile itself — a 1 mm mismatch shows up as a loose fit by midwinter.

What Window Seal Replacement Involves Step by Step

The job usually takes less time than owners expect, and in most cases the sash stays on its hinges. Below are the stages we follow and how the finished result is checked.

The replacement process from diagnosis to check

  • Diagnosis: we inspect the rubber, the closing pressure and the hardware to confirm the seal itself is at fault.
  • Removal: the worn strip is pulled out of its channel without cutting or bending the profile edges.
  • Cleaning: the channel is cleared of grit and old residue so the new strip seats fully along its length.
  • Fitting: the fresh strip is pressed into the channel on the moving part, the frame and the impost.
  • Check: we test for draughts and adjust the closing pressure where the strip alone does not close the gap.

Do we need to remove the sash

In most cases we do not remove the sash, since the seal sits in an accessible groove and can be replaced in place. A window seal replacement in Astana is done with the sash left hanging whenever the channel runs clear around the perimeter and the hardware is sound. Pulling the sash off makes sense only when the channel is hard to reach behind the frame or the hinges and locking gear need attention at the same time. Leaving it in place also avoids disturbing the alignment that keeps the sash closing smoothly — refitting it badly is what causes rubbing, a loose handle and a draught that no new strip can fix. Before we finish, the unit is closed and opened again and the pressure is set so the rubber compresses evenly. If the gap stays after that, the cause is usually the hardware, not the seal.

Which Windows and Doors We Can Re-Seal with Window Seal Replacement

Seals wear out on more than a standard plastic unit. Below we set out which frames and doors we take on, and where the line runs between a job you can do yourself and one that needs a fitter.

Types and manufacturers we cover

We replace seals on plastic, aluminium and wooden units, on balcony doors and loggia panels, and on frames from any manufacturer. That includes the common PVC systems in Astana — KBE, Rehau, VEKA and Provedal — plus older wooden units and aluminium loggia glazing. The profile decides which cord goes in: a Rehau opening and a Provedal opening take different shapes, so the fitter matches the seal to the actual channel rather than to the age of the frame. We also re-seal balcony doors and loggia units, where the moving panel sits heavier and the rubber compresses harder along the hinge side. A balcony door seal takes more wear than a standard one because it is opened far more often, so check it first when a room feels cold near the door.

When to call a fitter instead of doing it yourself

A seal can be replaced by hand, but the job goes wrong when the slot is not cleaned, the wrong profile is chosen, or the closing pressure is left uneven afterwards. The recess collects dust and old rubber fragments; if those stay in, the new cord sits proud and the panel no longer closes flush. Choosing a profile by thickness alone is the second trap — PVC channels differ in width and depth even within one brand. And once the seal is in, the closing pressure has to be checked and adjusted, or the draughty corner simply moves to the other side. The most common self-replacement mistake is buying a seal by length alone without checking the recess shape, which leaves a gap that only shows up on the first cold snap.

Warranty, Payment and How to Book

The terms below answer the main doubts before work starts — what is covered if something goes wrong, when you pay and how soon a measurer arrives. We take these points in turn.

What the warranty covers

We give a twelve-month guarantee on window repair, covering both the labour and the parts we replace, including the new seal. The same term applies whether we re-seal a plastic sash, a wooden frame or an aluminium profile from KBE, Rehau, VEKA or Provedal. Separate terms sit alongside it: five years on installation and three years on glass unit replacement, so a job that grows from a seal swap into a full unit change keeps its own cover. This cover matters most in the first heating season, when a poorly fitted seal shows itself as condensation or a draught, so keep the paperwork until the cold months pass.

Free measuring, fixed price and payment after installation

  • Measuring: free, with the measurer coming at a time that suits you and checking every unit you plan to re-seal.
  • Fixed price: the sum is set in the order after measuring, so it does not change later.
  • Payment: after installation, by cash, card or Kaspi.
  • Contact: we reply on WhatsApp within five minutes, seven days a week, from 09:00 to 22:00.
  • Care: wipe the new seal with a soft cloth and avoid abrasive cleaners to keep it flexible.

What to consider before window seal replacement

A worn seal is among the cheapest faults to fix on a window, and the signs are readable once you know where to look. Here is what to keep in mind before you call anyone.

  • Draught pattern: Air moving evenly along the sash edge points to the seal, while a leak at a single corner usually means pressure or hardware.
  • Material for cold: EPDM and silicone keep their flexibility through freeze-thaw cycles better than plain rubber, which hardens and cracks.
  • Three separate runs: The sash, frame and impost each carry their own seal line, and each wears at its own rate.
  • Clean groove first: Wiping dust and old adhesive out of the groove before fitting is what makes a new seal sit tight and last.
  • Warranty signal: A one-year warranty covering both labour and replaced parts is the clearest sign the work will hold through the heating season.

Questions about window seal replacement in Astana

Seal replacement, selection, restoration, condensation

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01What makes a plastic window the best choice?

The best window is one that keeps heat for a long time: with a multi-chamber profile and a quality seal. But any seal ages over time — we replace it on windows from any manufacturer (KBE, Rehau, VEKA, Provedal, etc.).

02Can the rubber seal on a window be replaced without removing the sash?

In most cases, the sash does not need to be removed: the old seal is pulled out of the groove and a new one is put in its place right on site. The sash is removed only if the seal cannot be reached otherwise or if it is stuck tight.

03The rubber has become hard and cracked, can it be restored or only replaced?

Hardness and cracks are irreversible changes in the material, so such rubber cannot be restored. Lubricants and impregnations give only a temporary effect; it is more reliable to replace the seal with a new one.

04Which seal is best for plastic windows?

For plastic windows, EPDM is most often used: it tolerates frost and temperature changes well and lasts longer. Silicone is softer and more elastic but more expensive, while rubber ages faster in the sun.

05If the rubber is replaced, will condensation on the glass disappear in winter?

Not always: replacing the seal eliminates drafts around the perimeter, but condensation often appears due to indoor humidity or poor air flow. If water remains on the glass after replacement, it is worth checking ventilation and the ventilation mode.

06Should the seal be replaced on all windows at once or can it be done one by one?

You can do it one by one: the seal wears unevenly, and it should be replaced where it has already cracked or lets air through. Doing all windows at once is usually for convenience if the seals were installed at the same time and have worn equally.

Reviews of window seal replacement in Astana

4,9based on 8 reviews
★★★★★
Спасибо большое за качественную работу! 😊 Поменяли резинки на окнах, всё сделали аккуратно и профессионально. Мастера вежливые, работу выполнили хорошо. Остались довольны результатом! Рекомендую всем, кому нужна замена резинок на окнах. Рахмет мастеру Батырхану👍
Gulmaral AldashevaOctober 16, 2026 · Review from 2GIS
★★★★★
Огромное спасибо ребятам за работу! Заменили старые уплотнители на окнах, которые жутко сифонили. Мастера приехали вовремя, всё сделали быстро, чисто!!! Настоящие профессионалы, рекомендую!!!👍👍👍
Xeniya SuleimanovaOctober 13, 2026 · Review from 2GIS
★★★★★
Терезелерден жел кіріп жүрген еді, регулировка жасатып, уплотнитель ауыстырдық. Бірден бірнеше мәселені шешіп алдық спасибо за качеству 👏🏽👏🏽
Бекжан ИсмаиловSeptember 9, 2026 · Review from 2GIS
★★★★★
«Хочу выразить огромную благодарность вашим мастерам за профессиональный ремонт наших окон. Окна стали плохо закрываться и продували, в доме было прохладно. Мастер приехал вовремя, быстро нашёл причину, заменил изношенные уплотнители и отрегулировал фурнитуру. Окна открываются и закрываются идеально. Рекомендую всем!»
Динмухаммед КалиевAugust 17, 2026 · Review from 2GIS
★★★★★
Помимо сетки попросила посмотреть окно, которое плохо закрывалось. Мастер сразу отрегулировал створку и заменил уплотнитель. Спасибо.
Меруерт УшуроваJuly 27, 2026 · Review from 2GIS
★★★★☆
Спасибо ребятам из Центра окон. Сильно продували окна, дома тянул сквозняк. Приехали, проконсультировали, назначили дату ремонта. Потребовалось заменить фурнитуру на окне от застройщика и заменить резинки на одном окне, на втором регулировка и также замена резинок. Дома стало теплее и менее зябко. Благодарю. Из пожеланий - было бы здорово если рабочая команда приводила после себя пространство в порядок, забирала бы на переработку может быть или металлолом старую фурнитуру. В остальном ок.
Роман ЯкунинDecember 4, 2025 · Review from 2GIS
★★★★★
Спасибо мастерам всё сделали быстро заменили пакет резинки и механизмы и регулировка всех окон и балконной двери в квартире стало теплей и шум с улицы стал тише рекомендуем воспользоваться услугами Центр Окон
Ельдар СадвакасовSeptember 23, 2025 · Review from 2GIS
★★★★★
Хочу выразить благодарность команде Центр окон за отличную работу! Заказывал замер и установку москитных сеток, а также регулировку окон и замену уплотнителей. С самого начала всё прошло на высоком уровне: специалист приехал точно обговоренный в срок, подробно рассказал о разных вариантах москитных сеток, помог выбрать оптимальный вариант под мои окна. Вежливое и профессиональное общение сразу внушило доверие. Установка тоже прошла быстро и аккуратно — монтажники пунктуальные, вежливые, видно, что знают своё дело. Всё сделали чисто, без лишнего шума и суеты. Я остался полностью доволен и качеством работ, и обслуживанием. Теперь в квартире стало намного комфортнее — окна герметичны, а от насекомых надёжная защита. Рекомендую!
Artem Ch.June 28, 2025 · Review from 2GIS