EPDM contour
Fresh rubber presses the sash tightly and keeps dusty wind and summer heat out of the room. From 1 000 ₸ per linear m.


EPDM contour
Fresh rubber presses the sash tightly and keeps dusty wind and summer heat out of the room. From 1 000 ₸ per linear m.

German contour
Rubber from Germany dries out more slowly under the scorching sun and stays soft longer. From 1 200 ₸ per linear m.

Door seal
A door is opened constantly, so its contour wears out faster than window seals. Replacement — from 5 000 ₸ per piece.

Brush seal
Sand quickly wears out the pile on sliding windows at country houses and loggias. A new brush — from 1 150 ₸ per linear m.

Inter-frame
An extra layer between the frame and the sash keeps out dust and heat. From 2 800 ₸ per window.

5,097 reviews on review sites
Dust on the windowsill and heat in the room with the window closed are the first signals. We replace the rubber, and the window stays the same.
A rubber contour runs around the perimeter of the sash and frame, closing the gap when the window is shut. Dried-out rubber loses its elasticity, and through the loose contour sand, heat, and in winter cold wind get into the house.
Sun and dusty winds in Kyzylorda wear out the seal faster than in northern cities. The technician will clean sand out of the grooves, install a new seal for your profile, and adjust the sash pressure.

per metre of new seal including labour
warranty on replacement and new parts
payment after the work, cash or card
Four situations from our technicians' practice.

In winter, a balcony or office door lets in cold because its seal has worn out.
After renovation, the seal is covered in paint, has hardened and no longer holds the sash.
On cold days, the seal becomes covered in frost if warm air escapes through the contour.
Through a loose double glazing seal, dust and draughts get in near the glass.
For the sunny side — German rubber, for sliding aluminium windows at the country house — a brush, for a door — a durable contour.
PVC windows in an apartment

Elastic contour for most profiles, does not melt in heat or crumble.
sunny side

Dries out more slowly under the sun and keeps a tight seal longer.
balcony, office, terrace

Durable rubber for a door that is opened many times a day.
aluminium sliding

The new dense pile traps sand and dust at the frame tracks.
windows on the windy side

Extra rubber between the frame and the sash keeps the cool in and the dirt out.
The cost depends on the length of the contour and the seal you choose; the technician will give you the price before starting work.
| Type of work | Price |
|---|---|
| Seal for sash and frameEPDM contour | from 1 000₸ per linear m |
| German sealsun-resistant | from 1 200₸ per linear m |
| One window completeall contours | from 3 500₸ per window |
| Door seal for balcony or terracearound the perimeter | from 5 000₸ per piece |
| Brush sealaluminium frames | from 1 150₸ per linear m |
| Sand cleaning and lubricationextends service life | from 750₸ per linear m |
| Inter-frame sealplus one contour | from 2 800₸ per window |
| Eliminate draughtsgap along the contour | from 3 500₸ per sash |
| Pressure adjustmentfor the new seal | from 3 000₸ per sash |
| Liquid plasticseams and joints | from 1 500₸ per linear m |
| Wooden frame insulationSwedish technology | from 4 200₸ per linear m |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Book a technicianWhat you get from us.
on work and the installed seal
KBE, Rehau, VEKA, Provedal and others
we fix the amount after inspection
accepting the work: cash, card, Kaspi
that's how long to wait for a reply on WhatsApp
we'll come on a day that suits you
we take requests daily
we work across Kazakhstan
The technician's workflow.

Send a photo of the window on WhatsApp and tell us what's bothering you: dust, heat, frost or cold from the door.

The technician checks the contours, hinges and pressure, identifies the profile brand and gives the price before starting work.

We remove the old seal, sweep sand out of the grooves and lay the new seal in a single strip.

We adjust the sash pressure, check the window and door for draughts, and after that you pay.
Good to know
We handle window seal replacement in Kyzylorda as a direct contractor with our own fitters, not through an agency. We re-seal plastic, wooden and aluminium windows from any profile maker, including KBE, Rehau, VEKA and Provedal. Measuring and consultation are free, the price is fixed after measuring, and you pay only once the work is done.
Draughts and condensation are the two most common reasons people pick up the phone. Yet the seal is not always the culprit. Here is how to tell a flattened contour from a loose sash before you book a fitter.
A worn seal shows itself through a draught that runs evenly along the whole sash edge, while a loose hinge usually lets air in at one corner only. Look for a black or grey rubber strip that has gone flat, shiny or cracked where the sash meets the frame, and for gaps you can see against daylight. Fittings, by contrast, announce themselves through a handle that turns stiffly, a sash that scrapes the sill or a corner that lifts when you press it. Run a sheet of paper between sash and frame and pull it out at several points; if it slides free with almost no resistance along the full length, the contour has flattened and no amount of adjustment will bring the grip back.
We see condensation on the inner glass edge most often when the seal has lost its grip and warm room air reaches the cold frame, but heavy frost across the whole pane usually points to the glass unit itself. A damp patch that sits low on the sash and disappears once the contour is renewed is the classic seal symptom. Frost that spreads over the centre of the glass, or mist trapped between the panes, tells a different story: the unit has lost its gas fill or its edge bond. Before ordering a new glass unit, check the seal first — a fresh contour is the cheaper fix and often removes the damp patch at the bottom of the sash within a few days.
A seal is chosen to fit the profile, not picked by eye. Below are the contours we fit, how they differ, and why universal tape often lets a specific frame down.
| Seal type | Best for | What to watch |
|---|---|---|
| Rubber contour | Standard PVC profiles, everyday use | Hardens over time, needs occasional silicone care |
| Silicone contour | Doors and sashes opened often | Keeps elasticity longer |
| Universal tape | Quick fixes on odd grooves | Rarely matches profile depth exactly |
We replace seals on plastic, wooden and aluminium units from any maker, including KBE, Rehau, VEKA and Provedal, and we can do a single sash or the whole flat in one visit. The contour is matched to the groove of each profile, so a sash from one maker and a frame from another get the right fit rather than a trimmed compromise. Wooden frames take a slightly different contour than PVC, and aluminium units such as Provedal balconies need one that holds tension at the thinner wall. On a multi-sash unit it pays to inspect every sash at once — a contour that still looks fine on the sunny side is often already flat on the shaded one, and replacing them together saves a second call-out.
From the first message to the final draught check, the work can be closed in a single visit. Here is what each stage of the job involves and who does what along the way.
A single sash is usually re-sealed within the same visit, and we work seven days a week so the job can be booked for a day that suits you. A full round of seal replacement in Kyzylorda covers one leaf in most cases; larger frames or several sashes in a row take longer, and the fitter tells you the realistic timing at the measuring stage rather than on the day. Window seal replacement in Kyzylorda is booked the same way, and the fitter confirms the timing for your address at the measuring stage. We check the profile first, because a worn gasket on a plastic frame and a wooden sash need different handling. You pay after installation by cash, card or Kaspi, which means you can check the result yourself before any money changes hands.
A well-fitted contour holds its shape for years when it gets basic attention. Below we cover which products keep the material supple, how often to apply them, and what a stiffer sash after the swap actually means.
A quality gasket keeps its grip for years, and the single most useful habit is a thin coat of silicone grease on the seal twice a year, before and after the heating season. Wipe the contour with a damp cloth first, let it dry, then run a light film along the surface so it stays elastic through summer heat and winter cold alike. Silicone spray from a hardware shop does the job; a cloth with a few drops of glycerine works for small touch-ups. Skip anything oil-based — petroleum products soften the material and shorten its life instead of protecting it. The same rule applies to glass cleaner with solvents: spray it on the cloth, not straight onto the seal, and never scrub the lip with a stiff brush. A gasket kept supple blocks dust and draughts far longer than one left dry.
A fresh seal is thicker than the flattened one it replaces, so the moving panel can feel stiff for the first few days until the new contour beds in. That early resistance is normal and settles on its own once the material takes the shape of the frame. If the handle still needs real force after that, the fittings need a small adjustment rather than a thinner gasket. We check the closing pressure during the final test, adjusting the hinges and panel position before we leave, so the unit shuts evenly along all four sides. A panel that drags on one corner usually points to a hinge setting, not a faulty seal, and forcing the handle only wears the mechanism faster.
We work as the direct contractor with our own fitters, not as an intermediary that passes your order to a third party. Below is what the cover includes, how payment works and how to arrange a visit.
We give a one-year warranty on window repair that covers both the labour and the parts we replace, including the new seal. If the contour starts letting air through again within that year because of the fit or the material, we come back and put it right at no charge. The cover is tied to the order slip, not to a phone call, so keep that document. It also records the profile and contour type, which matters: a future fitter reads the slip and brings the exact match instead of guessing from the frame. Installation carries five years and glass unit replacement three. In our practice the seal itself rarely fails first — most callbacks come from fixings never tightened to the sash, which is why the fitter checks them during the swap.
To book, message us on WhatsApp with a photo of the frame and we reply within 5 minutes, seven days a week, to arrange a free measuring visit. The measurer comes at a time that suits you, takes the sizes, and helps choose the canvas and the fastenings — Z-brackets, pins or magnets, depending on your profile and floor. You pay only after installation: cash, card or Kaspi, with the price fixed in the order once measuring is done. Because we are the direct contractor, there is no middle layer adding its own margin or relaying your questions. Send the photo with the handle and the profile edge in frame — that lets the fitter bring the likely contour and fixings on the first trip instead of ordering them in.
The points below sum up what decides whether a seal swap holds: correct diagnosis, the right contour for the groove, a fixed price after measuring, and simple seasonal care.
Seal replacement, signs of wear, draughts, choosing the profile
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionA worn seal loses its elasticity to the touch, does not spring back when pressed and may crumble or crack. A good seal is flexible and fits tightly against the sash with no gaps.
If the seal is intact, the cause is more often loose hardware pressure, a misaligned sash or gaps at the glazing bead. During the inspection the technician checks the pressure and fit to find the real source of the draught.
You can replace the seal on just one sash if the others are in good condition. But over time seals wear evenly, so the technician often recommends replacing them across the whole window for consistent airtightness.
For these profiles the seal is chosen by the shape of the groove and its stiffness, so there is no universal seal. During the inspection the technician identifies the profile series and fits the right seal.
If the window is new and draughty, the cause is more often incorrect adjustment or installation rather than the seal. First check the sash pressure and the quality of fitting, and only then decide about the seal.
Replacing the seals will help if the frost and condensation are caused by a worn seal. If the cause is the double glazing or poor installation, a different solution will be needed, which the technician will determine.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp