Craftsman repairing a window sash in the living room
Technician visit from 3 600 ₸On-site inspection and diagnostics, work according to the agreed scheduleCalculate

Window Repair in Karaganda

Seal pressure and sash movement · adjustment

Sash adjustment

Basic adjustment of seal pressure and sash movement — from 3 000 ₸ per sash, complex with removal — from 4 000 ₸.

A craftsman holds an L-shaped steel hex key for adjusting hinges
GoogleYandex MapsZoon

5,097 reviews on review sites

What window repair in Karaganda is and when it is needed

It's worth calling a technician if there's a draught, the sash sticks, or the seal is worn.

How the service works

The usual reasons to call a technician are draughts around the sash perimeter, sticking or loose closing, worn seal, a broken handle or damaged double glazing.

Repair restores the window's function without replacing the unit. A technician visit is needed if the sash catches on the frame, the handle doesn't turn fully, or there's a noticeable draught from under the sash.

Technician in a dark blue T-shirt with a hex key at an open white PVC window sash
1 year

warranty on window repair — on work and replaced components

3 years

warranty on double glazing replacement

5 years

warranty on window installation

Work
AdjustmentSealHandleDouble glazingHardware

How window faults are fixed on site in Karaganda

Four typical problems the technician comes for, and what exactly they do on site.

Close-up of an L-shaped hex key in the trunnion on the edge of an open white PVC window sash
  • 01Draught from under the sash

    Check with your hand around the sash perimeter or place a sheet of paper: if it isn't gripped when closing, the contact contour is broken. The technician on site will identify where exactly the seal is lost.

  • 02Window doesn't close fully

    We adjust the hardware: set the locking points and handle movement so the sash closes tightly.

  • 03Sash has sagged and catches on the frame

    We adjust the hinges with sash alignment; if worn, we replace the hinges — from 4 750 ₸ per item.

  • 04Handle is broken

    We replace handles with removal and installation — from 2 750 ₸ per piece, matched to your profile.

Types of window servicing and adjustment work

Five areas of window work with a guide price per unit; the exact estimate is given by the technician after inspection.

Seal

Around the sash perimeter

Technician holds a roll of grey rubber seal, showing it for replacement

We replace seals in windows of any manufacturer, including KBE, Rehau, VEKA, Provedal.

from 1 000 ₸ per linear m

Hardware and hinges

Set per sash

A craftsman holds an L-shaped steel hex key for adjusting hinges

We replace sash hardware and hinges with sash alignment, and repair the mechanism.

from 4 750 ₸ per piece

Window sill and drip cap

With on-site fitting

A craftsman holds a new white plastic window handle for replacement

We install PVC window sills with on-site fitting and drip caps with sealing of the joint.

from 3 250 ₸ per linear m

Window insulation

Sash and reveal

A craftsman holds a small square double-glazed unit sample for replacement

We insulate windows and reveals: eliminate draughts and freezing around the perimeter.

from 1 000 ₸

Mosquito screen

Mesh and fixings

A craftsman holds a roll of gray mosquito netting for repair

We repair mosquito screens: replace the mesh and fixings, install screens on windows and doors.

from 2 500 ₸ per piece

Window repair prices in Karaganda

A single price list for window work: price per unit and what to clarify with the technician before ordering.

Type of workPrice
Visit and inspection by a technicianwithout ordering a repairfrom 3 600₸ per job
Basic sash adjustmentseal pressure and sash movementfrom 3 000₸ per sash
Complex adjustment with sash removalremoving and rehanging the sashfrom 4 000₸ per sash
Window handle replacementremoval and installationfrom 2 750₸ per item
Hinge replacementwith sash alignmentfrom 4 750₸ per item
Hardware repairrestoring the mechanismfrom 7 800₸ per job
Sash hardware replacementfull set per sashfrom 10 000₸ per sash
Seal replacementaround the sash perimeterfrom 1 000₸ per linear metre
Double glazing replacementto window dimensionsfrom 19 500₸ per m²
Broken glass replacementincluding installationfrom 8 000₸ per m²
PVC window sill installationcut to fit on sitefrom 5 500₸ per linear metre
Drip sill installationwith sealing at the jointfrom 3 250₸ per linear metre
Mosquito screen repairmesh and fixingsfrom 2 500₸ per item
Air vent installationinto the window profilefrom 6 000₸ per item

The price is fixed in the order after measuringMeasuring and consultation — freePayment after installation: cash, card or Kaspi

Book an inspection

Why customers order window work from us in Karaganda

Facts about the company that matter when choosing a window repair technician.

Repair warranty1 year

for work and replaced components

Double glazing warranty3 years

for double glazing replacement

Installation warranty5 years

for window installation

Free visit0 ₸

on-site inspection and diagnostics in Almaty

Urgent double glazing1 day

urgent production and replacement with a surcharge

Open every dayevery day

we accept requests every day

Measuring and consultation0 ₸

free, the measurer will come at a convenient time

Coverage17

cities of Kazakhstan where you can order work

How window repair in Karaganda is carried out

Four steps from request to checking the sash after work.

  1. A hand holds a smartphone with a dark screen near a white PVC window
    01Request

    Request

    You leave a request, the technician clarifies the address and a convenient visit time.

  2. A tape measure measures the lower edge of the window opening of a white PVC window
    02Free

    Measuring and diagnostics

    The technician takes dimensions, inspects the sash and determines the cause of the fault.

  3. A removed white window sash on a workbench next to a coil of new black seal
    03On site

    Work

    Adjusts the seal pressure, replaces the handle, seal or double glazing as needed.

  4. A finished white PVC window with a new seal and handle, the sash closed evenly
    04After work

    Check

    The technician demonstrates the result to the customer: how tightly the sash closes around the perimeter and how smoothly the handle moves.

Good to know

Window Repair in Karaganda with Our Own Crews

We handle window repair in Karaganda with our own crews, not through middlemen. We adjust sagging sashes, replace seals in windows of any brand, swap glass units within a day and insulate frames before winter. Measuring and consultation are free, the price is fixed after measuring, and every repair carries a one-year warranty on labour and replaced parts.

What Your Window Repair Is Telling You and Which Fix It Needs

A window rarely fails without warning. First come the signals — a draught along the edge, a leaf that drags, mist between the panes. Reading them correctly tells you which fix is actually needed.

Why a Closed Window Still Lets in Cold Air

A draught from a shut window almost always comes from one of three places — a worn seal, a leaf that no longer presses evenly against the frame, or hardware that has drifted out of adjustment. An even flow along the whole edge points to the rubber gasket, which hardens and flattens over years of heat and frost. A draught concentrated at one corner means the moving part sits skewed and the locking points no longer meet the strike plates squarely. Hardware drift shows up as a handle that turns too easily, with no resistance at the end of the stroke. Run a hand along the seal on a frosty day and compare the corners with the middle of each edge — where the chill bites hardest tells you whether the gasket, the geometry or the mechanism is at fault.

When a Sagging Sash Is Just Adjustment and When It Is Wear

A leaf that catches the frame at the bottom usually just needs re-hanging on its hinges, but if the handle turns halfway and stops, the locking mechanism itself is worn and needs parts. The two problems look similar from the room side and are easy to confuse. Sagging develops gradually as hinge screws settle under the weight of the moving part; adjustment restores the geometry in most cases. Wear is different — the tilt-and-turn mechanism inside, the cams and the gearbox lose their tolerances after years of daily use. Try lifting the handle gently while turning it; if the lock engages only with that lift, the hardware is on its way out and adjustment alone will not hold. We replace the mechanism and re-hang the leaf, and we cover repair labour and replaced parts with a one-year warranty.

Mist on the Glass and Cold at the Edge

Condensation between the panes means the glass unit has lost its seal and needs replacing, while mist on the room-side glass and a chill strip along the frame point to insulation and slopes rather than the unit itself. Fog trapped inside the sealed cavity cannot be wiped away — the desiccant in the spacer has absorbed all the moisture it can, and the unit has to come out. Room-side mist behaves differently: it appears when warm indoor air meets a chilled surface and disappears once that surface warms up. Wipe the inside of the glass; if the fog returns within minutes on the room side only, the unit is fine and the chill is coming through the perimeter. That is where insulation, seal replacement and slope work come in.

How a Window Repair Visit Runs from First Message to Final Check

A window repair is a technician coming to your home, not a sash shipped off to a factory. Here is the whole route, from your first message to the final check of the work.

From Your First Message to a Booked Visit

We reply on WhatsApp within 5 minutes, ask for a photo of the problem and a convenient time, and the measurer comes when it suits you, seven days a week. Measuring and consultation are free: the measurer takes the sizes, checks how the sash closes and helps pick the fittings. A handle that will not turn, a draught along the gasket, a cracked glass unit — each fault shows up differently in a picture, so send a shot of the whole unit plus a close-up of the damage. A single photo of the handle or the rubber strip saves a second visit, because the crew can bring the right parts the first time instead of ordering them after the fact.

What the Technician Does on Site

Almost every job is done on site in one visit — adjustment, gasket replacement and hardware swaps take minutes, and only the glazing itself is measured and brought back, with urgent replacement within a day. The technician tightens or realigns the sash, lifts a dropped corner back into the frame and changes worn seals or handles on the spot. If the double-glazed panel has failed, it is measured, made to size and fitted on a return visit; the urgent option runs within a day for a surcharge on the panel. Ask the technician to show you the old part before it goes in the bin; a straight swap you can see is the simplest proof the work was actually done.

Which Parts of the City We Cover and What We Take On

  • Central districts: crews reach the centre and the South-East by prior arrangement, seven days a week.
  • Maykuduk and Prishakhtinsk: the crew packs sealant and tools for both plastic and wooden profiles.
  • Loggias and balconies: glazed loggias take the same plastic and aluminium fittings as a standard flat unit.
  • Gazebos and verandas: outdoor structures need fastenings matched to the frame material and the floor height.
  • Flats and private houses: one booking covers a single unit or a full run of them in one go.

Window Repair or Replace and Where the Line Sits

Not every fault calls for a repair, and not every unit is ready for replacement. The line between the two is narrower than it looks, and most of it gets settled on site.

Can You Swap Just the Glass Unit

Yes — a sealed unit is replaced without touching the frame or the sashes, and urgent replacement is done within a day, with a three-year warranty on the new glazing. We measure the opening, order the pane to size, then lift out the old one and set the fresh one into the same rebate. Urgent production and fitting run within a single day for a surcharge, which matters when a cracked pane sits over a child's bed or a radiator. The surround, the hardware and the sashes stay in place throughout — nothing is re-hung and no profile is cut. A failed unit is worth swapping rather than patching, because the seal between the panes cannot be restored once moisture has entered and left fog inside.

When Repair Stops Making Sense

Repair stops making sense when the frame itself is warped, the profile is cracked through, or the same fault returns after a proper fix — at that point a new one costs less over time than repeated visits. A sash that drags can be re-hung, but a bowed surround keeps pulling the hardware out of line no matter how often it is adjusted. Cracked PVC around the hinge screws holds nothing, so the fix lasts weeks, not seasons. Count how many times the same sash has been adjusted in a year; three returns to one fault is a sign the surround, not the hardware, is the problem. On older wooden frames, rot in the lower corners is the usual tipping point.

A Quick Comparison of Common Jobs

Common faults matched to job and duration
SymptomJobWhat it involvesTime on site
Draught along the edgeSeal replacementOld gasket out, new inUnder an hour
Sash catches the frameAdjustmentRe-hang and align the sashUnder an hour
Handle turns halfwayHardware repairReplace the locking mechanismUnder an hour
Fog between panesGlass unit swapMeasure, order, fit new unitUrgent within a day
Cold strip at the frameInsulation and slopesSeal the perimeter, fit slopesOne to two visits

Plastic, Wooden and Aluminium Windows We Take On

The material of the frame decides how a repair is done and which parts a crew carries. Below is what changes for plastic, wood and aluminium, and where the difference actually matters.

Plastic Units and the Brands We Handle

On plastic units we adjust sashes, replace seals in units of any brand — KBE, Rehau, VEKA, Provedal and others — and swap glass units without touching the surrounding frame. A drooping leaf usually needs new corner gearing or a turn of the hinge pins, while a draught along the edge points to a compressed seal rather than a faulty unit. Window repair in Karaganda often comes down to exactly these two jobs, and both are done on site in a single visit. The PVC itself rarely fails; the moving parts and the rubber around it take the wear. On a mixed-brand flat the crew works through each opening in turn, matching parts to the section in front of them instead of ordering by logo. The seal brand matters less than its groove shape, so a technician matches the groove, not the label.

Wooden Frames in Older Homes

Wooden frames are worth restoring when the frame is sound and only the seals, hardware or paint have aged, while rot in the timber or a warped leaf tips the balance toward replacement. Old wooden units in courtyard houses and pre-fabricated blocks usually hold up well once the hardware is serviced and the gaps are re-sealed. Look at the joints first: cracked putty and a stiff handle are cosmetic, but a leaf that no longer sits square in the rebate signals deeper movement. Restoration keeps the original look of the building, which matters in older districts where modern units would stand out against the facade. Press a screwdriver gently into the lower corner of the frame; if it sinks in, the wood has softened and no amount of sealing will hold the draught back.

Aluminium Frames, Loggias and Gazebos

Aluminium frames on loggias, gazebos and verandas take the same adjustment and seal work as plastic, but the fastenings and hardware differ, so the crew checks the section before quoting. Thin aluminium rails flex differently from PVC, and the fixings that hold a leaf true on a plastic unit will not sit the same way in a cold-bent section. On enclosed balconies and outdoor structures the perimeter is the weak point: wind load on a gazebo or an open loggia works the seals loose faster than in a heated room. We fit and repair screens on loggia openings, gazebo openings and veranda frames, and the fastening is chosen to suit the material and the exposure. On a cold aluminium rail, condensation is normal and not a fault; sealing the perimeter and fitting slopes does more for comfort than swapping the unit.

Insulation, Slopes and Window Security

A repair often pulls two more jobs behind it: keeping the warmth in and keeping small children off the sill. Below we separate what runs with a repair and what is booked on its own.

Insulating a Unit Before Winter

Insulation starts at the perimeter — sealing the gap between frame and wall, refreshing the seal and fitting slopes — and we do it together with a repair so the draught is closed at the source rather than masked with a strip of foam. A worn seal is replaced with a new one matched to the profile, whether the unit is KBE, Rehau, VEKA or Provedal, and the mounting seam is filled and finished so the cold bridge at the edge disappears. The perimeter work can run alongside the repair itself, which keeps the frame from being opened up twice. Insulate before the first hard frost: sealants and foams cure poorly in the cold, and a rushed job at minus temperatures tends to open again by spring.

Slopes That Stop the Cold at the Frame

Slopes cover the junction between frame and wall and, done properly, they stop the cold bridge that makes the edge feel icy even when the seal is new. The panel bridges the rough mounting seam, hides the foam line and takes the cold away from the corner where the sash meets the masonry, so the perimeter reads warm to the touch instead of sweating. A slope fitted over a damp surface traps moisture and peels within a season, so the structure behind it has to be dry before the panel goes on — on older block homes that can mean a day or two of waiting between sealing and finishing.

Child Locks and Restrictors on Existing Units

A child lock or restrictor can be fitted to a unit that is already in use — the lock mounts on the frame and limits how far the sash opens. We fit the restrictor and check that the handle still turns through its full travel, so the sash keeps working as intended and not just as a fixed pane. Choose a restrictor that still lets the sash open for cleaning, otherwise the unit becomes a chore to maintain and gets propped open, which defeats the lock entirely. On tilt-and-turn sashes the limiter is set so the sash ventilates but cannot swing wide enough for a child to climb through.

Warranty, Payment and Choosing a Direct Contractor

A guarantee and clear payment terms are what separate a direct contractor from a middleman. Here is what our one-year cover includes, when you pay, and how to tell a company crew from a task passed to a stranger.

What the One-Year Repair Warranty Covers

Every repair carries a one-year guarantee on both the labour and the parts we replace, and if the same fault returns within that year we come back and fix it. The cover applies to the labour itself and to the components fitted during the visit, so a sash that starts catching again or a handle that works loose is handled as a claim rather than a new order. It runs alongside our separate terms for larger scopes: five years on installation and three years on glass unit replacement, each tied to its own work. Keep the order sheet with the list of replaced parts. A claim is settled faster when the crew can see exactly which component was fitted and when.

Paying After the Work and the Fixed Price

The price is fixed in the order after measuring, and you pay only once the work is done — by cash, card or Kaspi. Nothing is collected upfront: the technician finishes, you check the result, and payment follows the outcome. The measuring visit itself is free, and the measurer takes sizes and agrees the scope before any figure is written down. A figure locked in after that stage protects you from mid-job surprises. If a quote changes after the technician has seen the unit, ask what was missed at the first stage — a thorough inspection should have caught it. We reply on WhatsApp within five minutes and are open seven days a week, so scheduling does not have to wait for a weekday.

Direct Crews Versus a Private Handyman

A direct contractor with its own crews carries the guarantee as a company, while a private handyman's promise lasts only as long as he answers his phone. That difference matters more than the first quote: when a fault returns months later, a company still has a record of the work, the parts and the terms, and a handyman may have moved on to other work or changed number. Ask who will actually come to the door. If the answer is a dispatcher passing the task to a stranger, the cover has no one standing behind it. Doing the task yourself avoids the question entirely, but sash adjustment and gasket replacement need the right parts and a check of the frame.

Who arrives for sash repair and what they check

A short recap of what decides the outcome of a window repair: the right diagnosis, on-site work, honest limits, seasonal timing and written guarantees on the job.

  • Diagnose first: a draught, a catching sash and fog between panes are three different jobs, each with its own fix.
  • Most work is done on site: a technician finishes the repair during one visit, and only a glass unit is measured and brought back, urgently within a day.
  • Know when to stop: patching stops making sense when the frame is warped or the same fault returns after a proper fix.
  • Plan insulation before the frost: draught-proofing and slopes belong with a repair, not after it, and are easier while the frame is already open.
  • Check the paperwork: a company guarantee covering labour and replaced parts is what separates a direct crew from a private handyman.

Questions about window repair in Karaganda

Common requests — aluminium windows, hardware, winter repairs, technician visit

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Do you repair aluminium windows?

Yes, we repair aluminium windows: we replace handles, hinges, seals and double glazing. The scope of work depends on the window design and the condition of the hardware, so an inspection is needed first.

02What should I do if the window won't lock and the handle spins?

Don't force the sash, or you'll bend the hardware. Set the handle to the open position, press the sash against the frame and call a technician: usually a broken lock or a stripped handle is to blame.

03Can windows be repaired at home in winter?

Yes, we carry out most window repairs even in freezing weather: adjustment, replacement of handles, hinges and seals are done on site. Double glazing replacement is also possible, but timing depends on the window and the outdoor temperature.

04Do you repair windows in private houses?

Yes, technicians also visit private areas of Karaganda. They work with plastic, wooden and aluminium windows, including ground-floor windows and those with grilles.

05Will a technician come on a weekend?

Yes, we work without days off, so a visit can be scheduled for any convenient day. The technician confirms the visit time when booking.

06Can I replace just the window handle?

Yes, the handle can be replaced separately without touching the rest of the hardware. The technician will remove the old one and install a new one to match your profile.

Reviews of window repair in Karaganda

5,0based on 97 reviews on platforms
All reviews