Craftsman repairing the hardware of a wooden window
from 8 100 ₸ per windowOne-coat painting; restoration — from 18 000 ₸ per m². Free measuring visit.Calculate

Wooden Window Repair in Karaganda

Sanding and painting · m²

Restoration

We remove the old coating, fill cracks and repaint the frame. Price from 18 000 ₸ per m².

Wooden window after restoration with fresh varnish on the frames
GoogleYandex MapsZoon

5,097 reviews on review sites

What wooden window repair in Karaganda is

We bring back the frame's appearance and tightness without replacing the window: sanding, painting, repairing wood sections.

How it works

Restoration is the renewal of an existing wooden frame: we remove the old coating, fill cracks, replace damaged wood sections and repaint. The frame and sashes stay in place, only their condition changes.

Restoration differs from window replacement in scope: we don't touch the opening or install a new block, but bring what's already there into order. This option suits when the wood itself is strong and wear affects the coating, hardware and seal.

Honey-coloured wooden window with two sashes: frame, glass, hinges and a handle
Free

Measuring and consultation before work starts

Any color

Painting the profile in any color chosen by the customer

Original geometry

Restoration preserves the original geometry of the opening

What's included
SandingPuttyingPaintingWood replacementHardware

How wooden window restoration goes

Four stages from frame inspection to glass replacement if the pane is cracked.

Technician applies varnish to a wooden window frame with a brush
  • 01Frame diagnostics

    The master inspects the sashes, hinges and seal, checks how the window closes and identifies the cause of drafts.

  • 02Perimeter insulation

    We lay a seal around the sash perimeter to eliminate drafts and maintain ventilation.

  • 03Hardware replacement

    We replace worn handles, latches and hinges, adjust the sash movement so it closes without effort.

  • 04Glass replacement

    If the glass is cracked, we remove it together with the glazing bead and install a new one. Price from 8 000 ₸ per m².

Types of wooden window repair in Karaganda

Six typical issues the master arrives for, and what we do in each case.

Drafts from gaps

Perimeter drafts

Hands insert a new seal into the groove of a wooden sash

We insulate using the Swedish method: seal the sash perimeter without changing the frame.

from 28 000 ₸

Peeling paint

Coating wear

Hands sanding an old coat of paint off a wooden window frame

We sand the frame and repaint so the wood doesn't absorb moisture.

from 8 100 ₸

Rotten sash bottom

Wood damage

Hands gluing a new wooden block into the bottom of a window sash

We cut out the damaged section and put a new one in its place.

from 1 200 ₸/pc

Sash has swollen

Won't close

Hands plane the edge of a wooden sash with a plane, wooden window repair

We adjust the sash on site so it fits back into the opening.

from 8 000 ₸/m²

Glass cracked

Glass and glazing bead

A craftsman holds a small clean pane of glass in his hand, whole and transparent

We replace the glass together with the glazing bead, securing it around the perimeter.

from 8 000 ₸/m²

Glazing bead fell out

Glass fixing

Hands place a wooden glazing bead into position with a hammer during window repair

We put the glazing bead back in place or install a new one if the old one is broken.

from 8 000 ₸/m²

Wooden window repair prices in Karaganda

Price list for wooden window work; the exact amount is given by the technician after measurement.

Type of workPrice
Wooden window restorationsanding and paintingfrom 18 000₸ per m²
Wooden window paintingone coatfrom 8 100₸ per window
Wooden frame repairfixing misalignmentfrom 16 000₸ per job
Wooden window insulationSwedish methodfrom 28 000₸ per window
Balcony block repairwoodenfrom 53 500₸ per unit
Hardware replacementhandles, latchesfrom 1 150₸ per unit
Inter-frame seal installationaround the perimeterfrom 2 800₸ per window
Glass replacementglass and glazing beadfrom 8 000₸ per m²
Wooden window insulation using the Swedish methodfrom 4 200₸ per linear m
Master's visit and inspection (without repair order)from 3 600₸ per job

The price is fixed in the order after measurementMeasurement and consultation are freePayment after installation: cash, card or Kaspi

Book a measurement

Why customers order wooden window restoration from us

Eight facts about our work: warranty, visit, payment and schedule.

Warranty on work1 year

For window repair and replaced components

Payment after installation3 methods

Cash, card or Kaspi

Visit and inspectionFree

Window repair technician visit within the city

Working hoursNo days off

We accept requests every day of the week

Measurement and consultationFree

The measurer will come at a convenient time and take dimensions

WhatsApp response5 minutes

We reply to messages within five minutes

SealAny brand

We replace in KBE, Rehau, VEKA, Provedal and other windows

Coverage17 cities

Available in 17 cities of Kazakhstan

How wooden window repair is carried out in Karaganda

Four steps from request to acceptance of work.

  1. Hand holding smartphone by wooden window, ceramic vase on windowsill nearby
    015 minutes

    Request

    You write on WhatsApp, describe the window problem. We reply within five minutes and agree on a time.

  2. Tape measure stretched along wooden window sash during measurement before repair
    02At a convenient time

    Measurement

    After measurement you agree on the list of work, and the price is fixed in the order — then the technician works according to this list.

  3. A workbench with tools, sandpaper, paint and sealant for window repair
    03Depending on scope

    Work

    The technician sands, fills, paints the frame, replaces hardware and seals according to the agreed list.

  4. Repaired wooden window with fresh white paint: one pane per sash, brass hinges
    04After work

    Acceptance

    You check the sash movement, the tightness of the seal around the perimeter and the absence of draughts — the result must match the agreed list of work.

Good to know

Wooden Window Repair in Karaganda

We repair wooden windows in Karaganda with our own crew, no middlemen. We diagnose whether the frame can be saved, then handle sash re-hanging, glazing beads, glass or glass units, seals and repainting. Measuring and consultation are free, the price is fixed after measuring, and every repair carries a 1-year warranty on labour and replaced parts.

Can Your Old Wooden Window Be Saved or Does It Need Replacing

Repair almost always costs less than replacement, but there is a threshold where the timber stops holding. Here is how a craftsman tells the difference before any work starts.

The signs a wooden frame is still worth repairing

We look at four things before quoting a repair — the timber is sound and dry, the leaf still closes into its rebate, the glazing bead holds the glass tight, and the rot has not reached the joint at the reveal. A window that dried and shrank over decades usually needs the sash re-hung, the hardware adjusted and the seals renewed rather than a whole new unit. Surface cracks in the paint are cosmetic and say nothing about the wood underneath. What matters is the material behind the bead and around the joints, where moisture sits longest. If a screwdriver presses in firmly and comes out dry, the structure keeps decades of life. On that kind of opening, wooden window repair in Karaganda is a straightforward job for our team, and the leaf returns to the same rebate it was cut for.

When replacement makes more sense than repair

If the rot went through the lower corner joint or the reveal, patching will not hold a seal for long, and we say so instead of selling a repair that fails next winter. Soft timber that gives under a screwdriver at the sill is the clearest signal — a patch there typically returns within a season. A new unit or a full window replacement settles the problem once and opens the way to modern glazing at the same time. We install windows with a five-year warranty on the fitting, so the choice between patching and replacing is worth making honestly at the measuring stage rather than after the first cold snap.

What the Repair Actually Covers Step by Step

A window repair of this kind is a set of jobs rather than one operation. Below is what a fitter actually does on a visit and in what order the work runs.

Sash re-hanging, hardware and glazing beads

A leaf that drags or will not latch usually needs re-hanging rather than a new hinge, and we replace the glazing bead when it has cracked or pulled away from the glass. Re-hanging means taking the sash off its hinges, checking the frame rebate and the corner joints, then setting the leaf back square. Hardware follows the geometry: handles, stays and latches are adjusted or swapped once the sash sits true. Glazing beads are the thin timber strips holding the glass, and a loose bead lets water sit against the putty line. We renew the strip where the timber has split or the nails no longer bite. Re-hanging restores the geometry of the leaf so it sits square in the rebate again; once that is done, the seal and the latch line up without forcing, which is what actually stops the draught.

What we check and replace on a typical visit

Checks and replacements made during a standard repair visit
What we checkTypical actionDone on site
Sash alignment and latchRe-hang and adjustYes
Glazing beadReplace cracked or loose beadYes
Seal around the sashRenew the sealYes
Glass or glass unitSwap glass or fit a unitYes
Paint and bare timberSand and treatYes
Lower corner jointAssess for rotYes

Stopping Draughts and Getting the Window Ready for Winter

A draught from a timber window almost always follows one of three lines — the sash, the seal or the reveal — and each one is dealt with differently. We take them one at a time.

Where the draught actually comes from

We trace a draught to one of three places — a leaf that no longer sits tight, a flattened seal, or a gap where the frame meets the reveal — and fix that line rather than sealing the whole unit. A leaf that has dropped on its hinges leaves a hairline gap along the closing edge; a compressed seal stops springing back against the sash; a shrinking gap at the reveal lets cold air in behind the casing. Each cause has its own remedy: re-hanging, a fresh seal, or insulating the reveal. Sealing everything at once hides the cause and traps moisture in the timber; finding the single line that leaks keeps the frame breathing and the repair lasting.

Renewing the seal and insulating without a new frame

We renew the seal on timber units of any make and insulate the reveal, so the frame stays and the draught goes, and we do it seven days a week. Seals are replaced on frames from KBE, Rehau, VEKA and Provedal as readily as on older sashes, and the reveal is packed and finished so cold air stops travelling behind the casing. Such a window wants to be serviced before the cold sets in, not during it — seal and paint applied in mild weather cure properly, while a winter patch tends to peel by spring. Book the work for early autumn and the same repair holds through the whole heating season.

Glass, Glass Units and Repainting the Timber

Glazing and finish are the two parts of a repair most often postponed to "sometime later". Here is what each involves and which should come first in the finished job.

Fitting a glass unit into an old timber frame

A timber frame can take a sealed glazing unit in place of single glass once the rebate is checked and the bead is renewed, and we can turn a broken pane around within one day at a surcharge. The leaf comes out, the old putty and glazing points are cleared, and the rebate is measured before anything is ordered. A double-glazed panel built for that opening drops in where the single sheet sat, and fresh stops hold it without rattling. The rebate depth decides whether the new panel fits without standing proud of its stops; measuring it first avoids a result that looks right but leaves the sash unable to close.

Sanding, treating and repainting after the repair

We sand back the bare timber, treat it and repaint the frame as the last step of the repair, because a fresh coating over a new joint is what keeps water out of the wood. Sanding follows the grain across the repaired area until the old finish feathers flat into the sound surface. An antiseptic primer goes on the exposed timber first, then two coats of exterior coating on top. Frames on the sunny side of a block chalk and flake faster, so they reward a fresh coat every three to four years. Paint applied before the seal and the stops are set will crack along the joint within a season; leaving it until last lets the coating bridge the finished work instead of splitting over it.

The Measuring Visit, Timing and the Warranty

Three things usually decide whether a homeowner books a repair: how the visit runs, how long the job takes, and what happens if something fails afterwards. Here is how each of those plays out on a timber window.

The free measuring visit and how the work runs

The measurer comes at a time that suits you, takes the sizes and helps choose the job, and the visit costs nothing; we cover the city and reply on WhatsApp within five minutes. He checks the frame, the sashes and the hardware, then writes down what needs doing so the estimate reflects the real condition of the window rather than a guess over the phone. Timber frames in older blocks vary in section and settling, so on-site sizes matter more than any standard figure. Measuring and consultation stay free, and the price is fixed afterwards, so the figure you agree is the figure you pay once it is done. Ask the measurer to note the hardware brand and the leaf weight — that record saves time on a repeat call years later.

What the warranty covers and how you pay

Every repair carries a 1-year warranty on labour and replaced parts, a glass unit swap carries 3 years, and you pay after everything is finished by cash, card or Kaspi. The guarantee follows the components we fit, so a renewed seal, a new bead or a rehung leaf is protected together with the fitting itself. Payment comes last, once you have opened and closed the window yourself and checked that it shuts without a draught. A guarantee that names both the labour and the parts is the one worth checking — cover on the work alone leaves you paying for a failed seal or bead that was fitted wrong. Keep the order sheet: it lists the parts replaced and the date the cover starts.

What to check before restoring wooden windows

A short recap of what decides whether an old window is worth saving, how the work is carried out and what to confirm before anyone starts.

  • Repair versus replacement: a window is usually worth saving while the wood is dry and rot has not reached the corner joint or the reveal.
  • On-site work: most repairs happen without taking the frame out, covering the moving sash, the bead, the seal and the pane.
  • Draughts: a leak is traced to one line rather than sealed everywhere at once, which keeps the timber dry.
  • Glazing and paint: an old leaf accepts a sealed unit once the rebate is measured, and repainting belongs at the end of the job.
  • Paperwork: a measuring visit fixes the price in the order, and a warranty should name both the labour and the parts.

Questions about wooden window repair in Karaganda

Old window repair, wood restoration, insulation, mosquito screens

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can old wooden windows in a Khrushchyovka in Karaganda be repaired or is replacement easier?

In most cases, old wooden windows in Khrushchyovkas are repaired: the seal is replaced, the hardware is adjusted, and insulation is added around the perimeter. Replacement is needed if the frame is badly rotted or deformed, which the technician will determine during inspection.

02What is done with dried-out wood in a wooden window—is it filled or is the sash replaced?

Dried-out wood is usually filled and, if necessary, the glazing bead is replaced, while the hardware is adjusted so the sash fits tightly into the opening again. A badly damaged sash is sometimes easier to replace, which the technician determines during inspection.

03The wooden sash has sagged and catches the frame—can this be repaired?

Sagging is usually fixable: the technician adjusts the hinges and hardware and, if necessary, reinforces the joints. If the misalignment is caused by frame deformation, they will advise whether repair is enough or replacement is needed.

04Can a modern double glazing unit be installed in a wooden frame instead of old glass?

Yes, in most wooden frames the glass is replaced with a double glazing unit without replacing the frame, if the seating allows. The exact feasibility and thickness of the unit are determined by the technician after measuring the specific window.

05Is it realistic to insulate wooden windows for the winter to stop drafts without replacing them completely?

Yes, perimeter insulation, seal replacement, and eliminating drafts help get through the winter without replacing the windows. How much this helps depends on the condition of the frame and sashes, which is visible during inspection.

06Do you make and fit mosquito screens for wooden windows in Karaganda?

Yes, we make mosquito screens to your dimensions and fit them on wooden windows, with the measurer selecting the fixings for the window profile. It is advisable to remove the screen for the winter.

07Will a technician come for a free measuring visit for a wooden window at a convenient time?

Yes, measuring and consultation for a wooden window are free, and the measurer will come at a convenient time. They will take dimensions, assess the condition of the frame and sashes, and advise what needs to be repaired.

Reviews of wooden window repair in Karaganda

5,0based on 97 reviews on platforms
All reviews