Sash adjustment
Simple adjustment from 3 000 ₸ per sash, complex with sash removal — from 4 000 ₸.


Sash adjustment
Simple adjustment from 3 000 ₸ per sash, complex with sash removal — from 4 000 ₸.

Seal replacement
We replace seals in windows of any manufacturer, price from 1 000 ₸ per linear metre.

Handle replacement
A new handle instead of a broken or sticking one, work from 2 750 ₸ per item.

Hinge replacement
We replace hinges if the sash has sagged and catches the frame, from 4 750 ₸ per item.

Double glazing replacement
Double glazing replacement from 19 500 ₸ per m², urgent production available.

5,097 reviews on review sites
Repair restores a tight seal, smooth operation and quiet in the room without replacing the whole window.
A window consists of a frame, sash, hardware, seal and double glazing. Repair affects the part that has stopped working: the seal, hinges, handle, rubber or the double glazing itself.
Hardware includes handles, hinges, locking mechanisms and seals — they are adjusted or replaced when worn. The seal is a rubber contour around the perimeter of the sash, which hardens over time and stops keeping heat in; it is replaced with a new one. Double glazing is a sealed unit of glass panes; if it cracks, fogs up from the inside or is damaged, it is replaced entirely.

warranty on work and replaced components
we accept requests daily
technician call-out and inspection in Almaty
Four common sash conditions where repair costs less than replacing the window.

We adjust the seal and replace it if the rubber has hardened or cracked.
The hardware has shifted or is sticking — the technician adjusts the mechanism and checks the sash movement.
The sash catches the frame at the bottom corner — we adjust the hinges and set the geometry.
If the mechanism is worn, we replace the sash hardware — from 10 000 ₸ per sash.
Five works with price per unit: sash, item, linear metre or the whole job.
per sash

Simple adjustment of the seal and sash movement without removal.
per linear metre

Replacement of the rubber around the perimeter of the sash or frame.
per item

A new handle instead of a broken or sticking one.
per item

Replacement of hinges when the sash sags.
per sash

Replacement of the sash mechanism when worn.
The table shows window repair works with unit of measurement and timeframe.
| Type of work | Price |
|---|---|
| Call-out and inspection by a technician | from 3 600₸ per job |
| Simple sash adjustment | from 3 000₸ per sash |
| Complex adjustment with sash removal | from 4 000₸ per sash |
| Window handle replacement | from 2 750₸ per item |
| Hinge replacement | from 4 750₸ per item |
| Hardware repair | from 7 800₸ per job |
| Sash hardware replacement | from 10 000₸ per sash |
| Seal replacement | from 1 000₸ per linear metre |
| Double glazing replacement | from 19 500₸ per m² |
| Broken glass replacement | from 8 000₸ per m² |
| PVC window sill installation | from 5 500₸ per linear metre |
| Drip sill installation | from 3 250₸ per linear metre |
| Mosquito screen repair | from 2 500₸ per item |
| Air vent installation | from 6 000₸ per item |
The price is fixed in the order after measuringThe price includes visit, diagnostics and adjustment without partsThe price within one job depends on sash size, number of locking points and hardware type
Call a technicianFacts about the company that matter when choosing a window repair technician.
for work and replaced components
for double glazing replacement
for installation work
we accept requests daily
cash, card or Kaspi
urgent double glazing production
of Kazakhstan, including Shymkent
measuring and consultation are free
Four steps from request to checking the work.

You write on WhatsApp — we reply within 5 minutes, clarify the problem and a convenient time.

The technician arrives, inspects the sash, hardware and seal, and names the cause.

Adjusts, replaces the handle, hinges, seal or double glazing — depending on the fault.

The sash closes tightly, moves smoothly; the technician shows the result and fixes the price in the order.
Good to know
We handle window repair in Shymkent with our own crews, not middlemen. We adjust hardware, replace seals on KBE, Rehau, VEKA and Provedal profiles, swap glass units (urgent replacement within one day), and stop draughts. Measuring is free, you pay after the work, and repair carries a 1-year warranty.
A window rarely fails without warning. It signals through draughts, stiffness, fog between the panes or a handle that turns too freely. Here is what each symptom points to and which repair it calls for.
A draught along the sash edge almost always comes down to one of two things — a worn seal or a loose pressure setting, and we check both before quoting any work. The gasket is the rubber strip running the full perimeter; once it hardens and flattens, cold air slips through the gap. The pressure setting is controlled by the locking cams that pull the sash tight against the frame. If the draught sits only at the corners, the rubber is the usual culprit; if it runs along the whole edge, the fitting needs adjusting. On a multi-storey block the effect is worse on the windward side, which is why the same fault feels mild on one wall and sharp on another. Ask for the pressure check first — it is the cheaper of the two fixes.
Fog between the panes means the sealed unit has lost its seal and cannot be repaired from outside, while a spinning handle is usually a stripped spindle or a loose fixing. A unit that fogs between the panes has failed at the edge spacer and needs replacing as a whole; wiping it will not help. Condensation on the room-side face of the glass is a different matter — that is moisture and ventilation, not a broken unit. The handle that turns without engaging the lock is a spindle worn smooth or a screw that has backed out, and both are quick to sort. Do not force a spinning handle — the cam inside the lock bends and turns a small fix into a full fitting swap.
Heat expands the profile and dust settles in the hinge tracks, so a sash that closed cleanly in spring can start catching or dragging by mid-summer. The PVC frame grows a fraction in direct sun, and a sash set tight in cooler weather rubs against it once the frame swells. Grit is the second factor: it packs into the hinge channels and the locking rail, and the moving parts start to grind. The summer and winter pressure modes are real, but switch them deliberately — a tight summer setting wears the rubber faster. A light clean of the tracks and a check of the hinge screws solve most seasonal stiffness. If the sash still catches after that, the frame has moved and the fitting needs re-setting by a technician.
The most expensive repair is the one done for nothing. Here is where a window is honestly fixable, and where new glazing or a fresh sash pays off over the long run.
If the frame is sound and the fault sits in the hardware, seal or glass, we repair it — replacing a whole unit for a worn seal or a loose hinge wastes money. Our crews handle window repair in Shymkent directly, so the same people who diagnose the fault carry out the fix. A failed seal, a handle that no longer latches, a sash that scrapes the rebate, a draught along the edge — each of these is a component-level job on a frame that still holds its shape. We check the geometry first: measure the sash for skew, look at the corners, test whether the diagonals match. If the structure is intact, repair is almost always justified. If the carcass itself has twisted, adjustment gives only a temporary effect.
A fogged or cracked unit is swapped on its own — the surround, sashes and hardware stay in place, so you keep the opening and only change the glass. Condensation sealed between the panes, a hairline crack from a stone or a pressure mark near the spacer all point to the same conclusion: the sealed glazing has lost its integrity and no amount of wiping will bring the clarity back. The rest of the assembly is untouched, which keeps the job quick and the flat clean. A fresh pane makes sense while the sash and its surround still hold their geometry. If the structure is already moving, new glass will not solve the problem underneath it.
A timber unit can be repaired while the structure and joints are solid, but once the wood has warped or rotted through, replacement usually costs less over the years than repeated patching. Timber is workable: joints can be re-glued, sashes re-hung, surfaces refinished, and a sound carcass will serve for years more. The catch is upkeep — wood needs repainting and checking on a regular cycle, and each round of patching buys a shorter stretch than the last. Plastic and aluminium are simpler to live with in this respect. We repair plastic, wooden and aluminium units, so the call is made on the state of the structure, not on the material as such.
Below is what we actually do on site and which frames we do it on, so you can tell straight away whether your case is on our list.
| Window type | Typical faults | What we bring | What we check |
|---|---|---|---|
| Plastic | Draughts, stiff handle, misted pane | Seals, hardware, glass unit | Profile make and play |
| Wooden | Shrunk gaskets, loose hinges, swollen panel | Gaskets, hinges, adjustment | Timber condition and frame square |
| Aluminium | Failed seals, loose fixings, cold bridge | Seals, fasteners, thermal inserts | Profile system and fixing points |
We fit and repair glazing on loggias, gazebos and verandas too, where the frame often sits in a harsher spot than a standard flat unit. On an open veranda or a garden gazebo the panel takes direct sun, dust and temperature swings a living-room one never sees, and the rubber is the first part to give. We bring the same gaskets, hardware and double glazing, matched to the profile already there, and adjust the panel so it still closes tight after the season changes. In our practice, glazed loggias in multi-storey blocks also need a look at the joint, because that is where cold air enters once the outer rubber ages. If your gazebo or veranda unit is only draughty and not broken, a new gasket and an adjustment usually settle it in one visit.
Gaskets and fittings fail first in most units — the frame still looks sound, yet air slips through. Here is how to judge when a gasket is done, how it is matched to a profile, and what adjustment can fix.
A gasket is due for replacement when the rubber goes hard, flattens or starts to crumble, and the sash no longer keeps a draught out even with the pressure turned up. Run a finger along the rubber at the opening edge: material that stays compressed and keeps a dent has lost its spring, and no amount of tightening brings the contact back. Check the corners and the sill too, where dust and sun wear it out faster. If the strip pulls away from its groove or crumbles when you pinch it, the material has aged past saving. A five-minute check along a single opening tells you more than a full sweep of the flat.
We replace seals in units of any manufacturer, including KBE, Rehau, VEKA and Provedal, matching the strip to the profile rather than forcing a universal one. Each system carries its own groove geometry and wall thickness, so a gasket cut for one chamber does not seat the same way in another. A strip that sits too loose lets air past the corners; one that sits too tight stops the leaf from closing flush and loads the hinges. Matching the rubber to the frame keeps contact even along the whole perimeter, which is what actually stops the draught. On aluminium systems such as Provedal the seal also copes with a thinner frame and different thermal movement than PVC. Bring a photo of the profile stamp inside the frame — it saves a return visit.
Hardware adjustment covers the hinges, the handle and the pressure setting, and a correctly set sash closes firmly without needing to be slammed. A handle that spins or feels loose usually means the spindle or the locking cam has worn, not that the whole unit is finished. Hinges carry the weight of the moving part, so a sagging corner shows up first as a scrape at the bottom and a gap at the top. The pressure setting is the eccentric pin on the locking points: turned one way it pulls the leaf tighter, the other way it eases off. We adjust all three together, because a tight setting on worn hinges just wears the rubber faster. Set the pressure for the cold season only — a permanent tight setting compresses the gasket and shortens its life.
From the first message to the final check, here is what happens step by step — and where you can gain time if a pane has cracked and cannot wait.
You message us, we reply on WhatsApp within 5 minutes, and the measurer comes at a time that suits you — measuring and consultation are free. The measurer takes exact sizes, checks the profile and the fittings, and helps you choose the mesh and the fixings for your unit and floor. He also looks at what actually failed — a seal, a hinge, a pressure setting or the glazing itself — because the repair plan depends on that, not on a guess over the phone. We fix the scope of work and the price in the order right after measuring, so the invoice after the visit holds no surprises. In my experience, most disputes start when a figure is quoted off a photo — ask for it in writing before any work begins.
Most repairs are done in a single visit, while a made-to-size glazing panel is produced and fitted on its own schedule depending on the job. A seal swap, a hinge adjustment or a handle replacement is usually finished within the same appointment, since the parts are carried on the van. A sealed panel is a different matter: standard sizes are quicker to source, while a non-standard one is manufactured to your exact measurements, so it is worth ordering in advance rather than on the morning you need it. Our crews handle window repair in Shymkent themselves, without passing the job to a third party, which keeps the timing predictable. When you book, tell the measurer the approximate size and the number of chambers — that single detail decides whether the panel comes from stock or from the line.
If a pane has cracked and cannot wait, we can produce and swap a glass unit within one day, with a surcharge added to its price. That option makes sense when the glazing is broken or cracked and cold, dust or rain is coming through — every extra day costs more in heating and in risk to the frame. When the problem is fogging between the panes, a day or two changes nothing: the seal has already failed, and the replacement can be planned calmly around your schedule. Our team produces and fits the new panel, and the 3-year warranty on glass unit replacement covers both the part and the fitting. Before you call, cover the crack with tape on the room side — it holds the fragments together until the crew arrives.
A clear warranty and knowing exactly who turns up at your door often matter more than the repair itself. Here is what our guarantee covers, how payment works, and why a direct contractor is the safer arrangement.
Repair work carries a 1-year warranty covering both the labour and the replaced parts, glass unit replacement carries 3 years, and installation carries 5 years. That split reflects how long each stage is expected to hold: a new seal or a set of hinges wears at a different pace than a full sash install, so the cover is tied to the component rather than bundled into one number. The parts clause is what customers ask about most, and it is the one that matters — if a seal we fitted or a handle we swapped fails inside its term, the fix is on us, not on you. Keep the order sheet with the date and the components listed; that single document is all you need to make a claim.
You pay after the work is finished, by cash, card or Kaspi, and the price is fixed in the order once measuring is done. Nothing is collected up front and nothing shifts mid-way: the measurer records the sizes, the components and the labour in the order, and that figure stands whether the job runs long or short. We take cash on the day, a card on a portable terminal, or a Kaspi transfer once you have walked around and checked the sashes yourself. It is a small detail that removes a large worry — you see the result, test the handle and the seal, and only then reach for your wallet.
With a direct contractor, the team that measures is the team that repairs, so responsibility sits with a single party instead of a chain of subcontractors. When a dispatcher books the visit and a different crew arrives, the person who quoted cannot vouch for the person who worked, and a claim has to travel back up that chain before anyone acts. Ask which team will physically do the work and whether those tradespeople are on the company's own payroll — the answer tells you more than any advert. In our practice the same hands measure, fit and answer the phone afterwards, which is why a warranty question gets a straight answer rather than a forwarded message.
A window rarely fails all at once — the symptom tells you which part gave way, and the right call on repair versus replacement usually follows from it.
Repair, adjustment, double glazing, seal
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionYes, in most cases the window is repaired: fixings are replaced, the seal is changed, or the sash is adjusted. Replacement is only needed if the frame or double glazing is seriously damaged.
If the sash catches on the frame, closes poorly, a draft appears, or the handle turns with effort, it's time to adjust. This extends the life of the fixings and keeps the heat in.
Yes, if there is a crack or fogging from the inside, the double glazing is replaced entirely. Repairing individual panes is ineffective because the chamber's seal is broken.
We repair windows of any material: plastic, wooden, and aluminium. For each, we select suitable components and work technology.
A technician comes to the home and performs most work on site: how long it takes depends on the window and the type of repair. Urgent double glazing replacement is done within a day.
Often the cause is weak pressure or a worn seal, in which case adjustment and seal replacement help. If condensation is between the panes, the double glazing is already depressurised and must be replaced.
Yes, we replace the seal on windows from any manufacturer, including KBE, Rehau, VEKA, and Provedal. The technician will select the right tape for your system and climate to ensure a tight fit.
Yes, we offer urgent production and replacement of double glazing within a day, though at a surcharge. The usual timeframe depends on the size and type of double glazing.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp