Sash adjustment
Simple adjustment of sash pressure and geometry — from 3 000 ₸ per sash; complex adjustment with sash removal — from 4 000 ₸.


Sash adjustment
Simple adjustment of sash pressure and geometry — from 3 000 ₸ per sash; complex adjustment with sash removal — from 4 000 ₸.

Handle replacement
We replace the window handle, matching it by mounting size — from 2 750 ₸ per piece; the work takes little time.

Hinge replacement
We replace upper and lower hinges if the sash has sagged and catches the frame — from 4 750 ₸ per piece.

Seal replacement
We replace the seal to match your window profile — from 1 000 ₸ per linear meter, eliminating drafts along the contour.

Glass unit replacement
We replace the glass unit according to window dimensions — from 19 500 ₸ per m²; urgent production is possible within one day.

5,097 reviews on review sites
The technician services the sash, hardware, seal, and glass unit — based on what has failed
Window repair involves working on the components responsible for sash pressure and movement: hardware, hinges, handle, perimeter seal, and glass unit. The technician checks each component and fixes the one causing drafts, failure to close, or catching on the frame.
Work on slopes, window sills, and flashings is handled separately if the cause is broken sealing or freezing. A 1-year warranty applies to completed work and replaced components.

warranty on window repair and replaced components
warranty on glass unit replacement
warranty on window installation
Six common causes the technician addresses, and the work for each

Check the mark on the sash: if the seal is unevenly compressed or has cracks and creases, it is worn. If the mark is even but pressure is weak, the pressure is likely misaligned. The technician will check both components and fix the cause.
The hinges are to blame: they are adjusted, and if the hinges are worn out, they are replaced. After adjustment, the sash moves smoothly without catching the frame.
The handle is replaced with one matched to the mounting size so it fits into the standard position without modifying the profile.
A fault in the locking mechanisms of the hardware. The technician troubleshoots the hardware and adjusts the sash movement until it closes completely.
Visit and inspection by a technician — from 3 600 ₸ for the work without ordering a repair. When work is ordered, the cost is agreed after inspection.
Five repair services most often ordered in Pavlodar, with price per unit of work
For window profile

We replace the seal around the sash and frame perimeter, eliminating drafts and draughts.
To window dimensions

We replace the double glazing unit entirely if it is cracked or has lost its seal.
With fitting and sealing

We install a PVC window sill and drip cap with sealing of the joint to the frame and wall.
Mesh and fixings

We repair the screen: replace the mesh and fixings if the frame is intact.
Air flow and perimeter

We install a supply valve for constant air flow and work around the perimeter.
Units of work and 'from' prices — the exact amount is fixed in the order after measurement
| Type of work | Price |
|---|---|
| Technician visit and inspectionwithout ordering a repair | from 3 600₸ per job |
| Simple sash adjustmentpressure and geometry | from 3 000₸ per sash |
| Complex adjustment with sash removalwith sash dismantling | from 4 000₸ per sash |
| Window handle replacementmatched by mounting size | from 2 750₸ per pc |
| Hinge replacementupper and lower hinges | from 4 750₸ per pc |
| Hardware repairlocking mechanisms and micro-ventilation | from 7 800₸ per job |
| Hardware replacement on sashset for one sash | from 10 000₸ per sash |
| Seal replacementfor window profile | from 1 000₸ per linear m |
| Glass unit replacementby window dimensions | from 19 500₸ per m² |
| Broken glass replacementglass in existing frame | from 8 000₸ per m² |
| PVC window sill installationwith on-site fitting | from 5 500₸ per linear m |
| Flashing installationwith joint sealing | from 3 250₸ per linear m |
| Mosquito net repairmesh and fasteners | from 2 500₸ per pc |
| Supply valve installationfor constant air flow | from 6 000₸ per pc |
Price is fixed in the order after measurementMeasurement and consultation — freePayment after installation: cash, card, Kaspi
Call a technicianFacts about the company that matter before ordering: schedule, payment, coverage and response speed
daily, check reception hours with the manager
cash, card or Kaspi
of Kazakhstan, including Pavlodar
we work across Kazakhstan
on WhatsApp for your request
for work and replaced components
the measurer will come at a convenient time and take the measurements
the price is fixed after measuring
From request to checking the sash operation

Describe what is wrong with the window: draft, does not close, sash sagging. The technician will clarify the profile type and floor.

Clear access to the window: remove curtains, take things off the window sill. The technician needs free access to the sash and hardware.

Check together with the technician the sash movement and pressure around the perimeter: the window should close tightly, without jamming.
Good to know
We handle window repair in Pavlodar with our own crews, not through middlemen. We fix plastic, wooden and aluminium windows, adjust sashes, replace seals and glass units, and insulate frames. Measuring and consultation are free, the price is fixed after measuring, you pay after the work, and every repair carries a 1-year warranty on labour and replaced parts.
A window rarely fails without warning. Long before a leaf jams or cold air reaches the sofa, the gasket and hardware send small signals. Here is how to read them.
A draught along the leaf almost always comes from a worn seal or a sash that has lost its press against the surround, not from the surround itself. The gasket is a soft strip running the full perimeter, and it is the part that keeps out air, dust and moisture. Over heating seasons it flattens, hardens and shrinks into the corners, so the gap opens first where the two ends meet. On the hinge side the closing pressure is set by the hardware, and once it slackens the gasket stops touching the surround at all. Run a hand along the perimeter on a cold day — if the cold spot sits at the hinge side, the press needs adjusting before the gasket is blamed.
We adjust the leaf on its hinges so it sits square again, which clears the catching and restores the press without replacing anything. The moving part hangs on two or three hinge points, and each one carries a screw that sets height, side position and closing pressure. When those screws work loose, the leaf sags at the handle corner and starts to scrape the surround or the sill. Adjustment takes minutes with the right tool and needs no new parts. A dropped leaf usually tells you the hinge screws have loosened over seasons — catching it early keeps the mechanism from wearing unevenly.
A spinning or sticking handle is a hardware fault, and we repair or replace the mechanism rather than the whole unit. The grip drives a transmission bar hidden inside the leaf, and that bar moves the locking cams that pull it tight to the surround. A loose grip usually means the two screws under the cover cap have backed out; a spinning one means the square spindle has stripped its seat. Both are small parts. If the grip turns but the leaf does not move, the fault is usually in the transmission bar, not in the grip itself — worth checking before ordering a part.
Swapping a whole unit is different work and different money. Here is where repair still holds up, and where patching the same fault turns into a loop with no end.
We recommend repair when the frame and the glass unit are sound and the fault sits in the moving parts — seals, hinges, handles or the press. On a plastic, wooden or aluminium unit the profile carries the load and the fittings take the wear, so a sash that no longer pulls tight usually needs new hardware rather than a whole assembly. A handle that spins, a hinge that has dropped or a gasket that has gone flat are all local faults with local fixes. A unit that is fifteen or twenty years old can still be worth repairing if the profile is intact; age alone is not a reason to replace. Before you sign anything, ask which parts will be swapped and which will stay — a repair that names its parts is one you can check afterwards.
Replacement is the honest answer when the structure itself is warped, the profile is cracked, or the glazing has failed in a way that no repair can seal. A sealed unit is two or more panes with an air or gas chamber between them; once that chamber is breached, the assembly cannot be re-sealed from the outside. A warped sash is the harder case, because it has lost its geometry — fresh gaskets and hinges get pulled out of shape by the same twist that ruined the old ones. Patching such a window over a few seasons costs more than one clean swap. If the leaf sits crooked no matter how the hinges are adjusted, the surrounding structure is the problem, not the fittings.
Our measurer looks at the frame, the sash movement and the seal in one visit and tells you plainly whether the unit is worth repairing. The visit is free, and it covers the whole assembly rather than the one symptom you noticed: the press of the leaf, the state of the gasket along each edge, the way the hinges carry weight and whether the profile is still straight. Because we handle plastic, wooden and aluminium units in Pavlodar, the measurer can compare yours against the same type rather than guess from a photo. Ask the measurer to show you the fault on the spot — a press you can feel with your own hand is a better guide than any written estimate. A short diagnostic now saves you from paying twice for the same fault.
Fogging from the inside and a cracked pane look like two different stories, but both are settled at the level of the glazing rather than the whole assembly. Here is how to tell them apart and what happens next.
Fogging between the panes means the airtight cavity has failed, and no amount of wiping will clear it because the moisture sits inside. A double-glazed unit is two or more panes held apart by a spacer, with a dry air or gas chamber between them and the edges closed off from the outside air. Once that edge seal gives way, room humidity migrates into the chamber and condenses on the cold inner surface — a milky haze or drops that never go away, whatever you do on either side. Condensation on the room-side surface is a different problem — it points to ventilation or humidity, not to a broken assembly, so check that before ordering a replacement.
A cracked pane is a safety issue and a heat leak at once, and we can make and fit a replacement within a single day when the case is urgent. A fracture breaches the insulated cavity the same way a failed edge seal does, so the opening starts losing heat even before the crack spreads, and a star or a long running line can give way under wind load or a slammed sash. Urgent manufacture and fitting is done inside twenty-four hours, with a surcharge on the new glazing itself. Tape the crack on both sides before the crew arrives — it holds the shards in place and keeps the damage from spreading across the pane.
A new unit restores the insulation and the clarity of the glazing, and the replacement carries a 3-year warranty from us. The swap touches only the glazing package: the frame, the sash and the hardware stay as they are, so the room keeps its look and the work stays contained to the glass assembly. What people notice first is the silence and the warmth — a failed cavity leaks heat steadily, and a fresh one closes that path again. After the swap, give the new seal a few days to settle before judging the press — a fresh build can feel slightly tighter at first and then even out.
A repair visit is a short chain of steps, and at each one you know what is happening and what is needed from you — from the first message to the last handshake.
Measuring and consultation are free, the measurer comes at a time that suits you, and the price is fixed in the order once the sizes and the scope are clear. The appointment begins with a look at the frame itself: the specialist takes the sizes, tests how the sash moves, and helps you choose the design, the mesh and the fixings if a screen is part of the job. Nothing is ordered on a guess — the order is only written after the numbers are on paper, and that same figure stands when the team arrives. If you are planning window repair in Pavlodar, the measurer will also check the frame and the sash on the spot and set the scope before anything is ordered.
Our crews work seven days a week, so a weekend appointment is normal, and most repairs are finished on the same trip once the parts are on hand. A team arrives with the tools and the common parts for the fault you described, and a straightforward fix — a handle, a hinge, a seal, an adjustment — is closed before they pack up. Where a component has to be matched to your profile, the crew tells you at the door what they can finish that day and what comes back with them. Book a morning slot if the job involves a glass unit — it leaves daylight for the final inspection and for any adjustment on the spot.
You pay after everything is done, by cash, card or Kaspi, and the crew walks the frame through a final inspection with you before they leave. That pass covers what was touched and what sits next to it: the sash opens and closes, the handle turns, the seal meets the frame, the glass sits tight. Ask the crew to show you anything you are unsure about — that is what the last few minutes are for. Open and close the moving panel yourself during that pass: a press that feels right to your hand is the last word on whether the repair is finished.
Repair work is not tied to a single frame material. Below we set out which structures we take on and how the approach differs for each of them.
We repair plastic, wooden and aluminium units, and we change seals in products of any profile maker, including KBE, Rehau, VEKA and Provedal. A PVC sash usually fails at the hardware — the hinge press drops, the handle works loose, the seal flattens against the frame. Wooden frames behave differently: the timber swells and dries through the year, so the sash can bind in spring and rattle in winter, and the fix is a re-press rather than a new part. Aluminium holds its shape well but transfers cold straight through the profile, which puts extra load on the seal and the hinges. Wooden frames move with the seasons more than plastic ones, so a wooden sash often needs its press checked twice a year rather than once.
We take on glazing on loggias, in private houses, gazebos and verandas, where the frame often sits in a harsher spot than a flat unit. A glazed loggia faces wind on one side and the warm flat on the other, so the seal on the outer contour works harder and the fixings take more load. In a private house the same unit may sit above a heated room and below an unheated attic, and that temperature split shows up first at the glass unit and the seal line. Gazebos and verandas are open to rain and sun for much of the year, and their frames collect dust and pollen that dry out the rubber. A veranda or gazebo frame faces more wind and temperature swing, so the seal there tends to wear faster and is worth checking before each cold season.
| Window type | Parts that wear first | Typical job |
|---|---|---|
| Plastic (PVC) | Seal, hinge press, handle | Adjust sash, replace seal |
| Wooden | Seal, frame movement | Re-press, seal swap |
| Aluminium | Seal, hinges | Adjust, seal swap |
| Loggia or veranda | Seal, fixings | Seal swap, re-press |
| Private house | Seal, glass unit | Seal swap, unit replacement |
A guarantee and a payment method say as much about a contractor as the repair itself. Here is exactly what we cover, why we work without middlemen, and how to start a request.
Every repair carries a 1-year warranty that covers both the labour and the parts we replaced. If a sash we adjusted starts catching again, or a handle we swapped feels loose, the same crew returns and puts it right under that term. The guarantee is tied to the specific job on your order sheet, not to a general promise, so it names the parts that went in and the labour that was done. Our installation service is backed separately for 5 years, and a full glass unit replacement carries 3 years, which matters when a small fix turns into a swap. Keep the order sheet with the fixed price and the parts list — it is what the guarantee is checked against if anything needs a second look.
We work with our own crews, so the specialist who measures, the one who repairs and the one who answers for the guarantee are all on the same team. That means the fault you describe on the phone reaches the hands that will actually open the sash, without being re-told to a subcontractor two steps down the line. A middleman structure adds a dispatcher between you and the job, and with it a gap where details get lost — the wrong hinge ordered, the wrong profile assumed. When a dispatcher never saw your unit, every claim has to be re-explained before anyone acts; a direct crew removes that gap between the fault and the fix. Ask any contractor who will physically turn up before you agree to the visit.
We reply on WhatsApp within five minutes, and having a photo of the unit and a short note on the fault ready speeds up the first answer. Send the picture, mention whether the sash drags, whistles or will not latch, and say which room it is in — that is enough for us to prepare. Measuring and consultation are free, and the measurer comes at a time that suits you. We are open seven days a week, and payment happens after the job is done, by cash, card or Kaspi. A photo taken straight on, with the handle and the hinge side both visible, tells the crew more than a long description over the phone.
A repair decision comes down to a few practical checks, and the list below pulls them together so you can act on what you have read.
Repair, adjustment, double glazing, safety
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionYes, in most cases no replacement is needed: the technician checks the seal pressure and condition, then adjusts the sash or installs a new seal. If draughts come through the frame joint, the joint is sealed.
Usually it's an adjustment: temperature changes cause the sash to settle and catch. The technician will align it and set the seal pressure, and will suggest replacing parts only if they are worn.
Yes, if the profile and hardware are intact, only the double glazing is replaced. We offer urgent manufacturing and installation within a day, but the timeframe depends on the size and type of double glazing.
Yes, we also repair wooden windows, especially in old houses. The technician will assess the condition of the sashes and hardware and tell you what can be fixed without replacing the window.
Our window repair technician can fix this. They will adjust the hinges, replace them if necessary, and the sash will stop catching the frame.
We install blockers, limiters and locks that prevent a child from opening the sash. The technician will choose the right option for your window.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp