Sash rubber seal
Fresh rubber and winter pressure mode — and the sash stops letting draughts in. From 1 000 ₸ per linear metre.


Sash rubber seal
Fresh rubber and winter pressure mode — and the sash stops letting draughts in. From 1 000 ₸ per linear metre.

Joint around the frame
We dry the wet joint and cover it with liquid plastic, outside — with sealant. From 1 500 ₸ per linear metre.

Warm reveal
We insulate the mouldy reveal from inside and finish it anew. From 19 900 ₸ per linear metre.

Window sill
We fill the gap under the window sill with foam and close it. From 15 000 ₸ per job.

Between-frame layer
An extra rubber seal between the frame and the sash removes frost at the bottom. From 2 800 ₸ per window.

5,097 reviews on review sites
First we find where the window loses heat, then we close exactly those places. No unnecessary work or overpaying.
First the technician checks the sash: whether the rubber is fresh and what pressure mode is set. Then the joint around the frame, the reveals and the window sill. Based on the inspection you get a list of works and a price, and the technician starts only after you agree.
Frost and the wind from the Irtysh in Pavlodar quickly blow heat out through gaps, and in panel buildings from the early 2000s window joints are often already wet. Once they are closed, you will feel the difference on the very first cold night.

linear metre of joint sealing indoors
warranty on repair and parts
the price is fixed after inspection
What Pavlodar residents complain about.

A tissue by the closed sash flutters — so the rubber or the pressure is not holding.
The foam by the frame is wet, and the wall around the window feels cold to the touch.
Moisture settles on the cold reveal and grey mould spots appear.
There is a void under the window sill, and the floor by the window is always icy.
Most often two or three of them are enough, the technician will say for sure.
PVC sash

Fresh seal and switching the hardware to winter mode.
around the frame

Liquid plastic keeps the foam from getting wet.
outside

Sealant protects the foam from wind and wet snow.
with mould

Insulation inside the reveal and clean finishing.
cold floor

Foam into the voids and a closed joint.
The final amount is made up of the works needed, the technician will name it before starting.
| Type of work | Price |
|---|---|
| Full window insulationthree jobs at once | from 3 800₸ per window |
| Rubber seal for the sashsoft contour | from 1 000₸ per linear metre |
| Gap around the perimeterwe stop draughts | from 3 500₸ per sash |
| Joint sealant indoorsliquid plastic | from 1 500₸ per linear metre |
| Joint sealant on the facadeoutside the window | from 2 000₸ per linear metre |
| Warm reveal, turnkeyinsulation inside | from 19 900₸ per linear metre |
| Window sill without gapsfoam and joint | from 15 000₸ per job |
| Wooden framesSwedish method | from 4 200₸ per linear metre |
| Micro-liftor one more locking point | from 1 700₸ per item |
| Between-frame layerone more rubber seal | from 2 800₸ per window |
| Thermal cameraleak snapshot | from 9 000₸ per job |
| Balconyinsulation from inside | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Call a technicianBriefly about our work.
for repairs and components
seal for KBE, Rehau, VEKA, Provedal
list of works and price before start
cash, card or via Kaspi
wait time for a reply
Saturday and Sunday are working
time for accepting requests
we work across Kazakhstan
Without unnecessary hassle.

Tell us on WhatsApp what you feel at the window: draft, damp, frost or cold floor, attach a photo.

The technician checks the sash, seam, reveal and window sill and gives a list of works with price.

We replace the seal, switch to winter mode, seal the seams, foam under the window sill.

We check with a napkin and hand for drafts, and after that you pay.
Good to know
We handle window insulation in Pavlodar with our own craftsmen, not through middlemen. A free measuring visit comes first, then we find where the draught actually enters and fix the seal, the seam or the glass unit as needed. You pay after the work, and the repair carries a one-year warranty.
A shut handle does not mean a sealed unit. Air finds three separate paths into a room, and each points to a different fix. Here is how to tell them apart before anyone touches the frame.
We read condensation in a corner, a chilled leaf edge and a draught that appears only in one room as three different signals, and each narrows down the cause before the measurer arrives. Water beading on the glass near the sash usually points to a faulty glass unit or a joint that has lost its fill, while a chilled strip along the leaf edge is the rubber seal giving way. A draught that shows up in a single room and nowhere else often traces back to that room's own seam or slope rather than to the whole flat. In our practice, the pattern matters more than the size of the gap, because it tells us whether the fix is a seal, a seam or the unit itself.
Insulation is not one job but a set of parts that work together. Some units need only a new seal, others need the seam or the glazing addressed. This section maps the parts to the symptom.
| Part | What it fixes | How we check it |
|---|---|---|
| Weatherstripping | Draught along the sash edge | Hand test around the closed sash |
| Installation seam | Cold from behind the frame | Inspection of the wall joint |
| Slopes | Draught from under the sill | Check of the slope joint |
| Glazing | Condensation and cold panes | Inspection for mist between panes |
We keep the existing glazing whenever the seal and the seam solve the draught, and we suggest a swap only when mist sits between the panes or the pane itself stays cold. Window insulation in Pavlodar usually starts with the weatherstripping, because a worn strip lets cold air past the sash long before the pane fails. Our measurer runs a hand around the closed sash first, then checks the wall joint and the slope finish, so the quote covers the part that actually leaks. A unit that fogs between the panes has lost its seal permanently, so no amount of new stripping will bring the clarity back and the pane has to be swapped. Replacement units carry our three-year warranty, which covers the sealed assembly itself.
The frame material changes what a craftsman can do without replacing the unit. Plastic, wood and aluminium each fail in their own way, and the right fix follows the material.
We insulate wooden frames by working on the putty, the glazing bead and the seal, so an old frame often keeps its character instead of being torn out. The putty line is where most heat escapes first: hardened putty cracks along the rebate, and a thin blade of cold air runs down the glass into the room. Refitting the glazing bead pulls the glass tight against the sash again, and a fresh seal closes the gap between sash and frame. Wood moves with the seasons, so the sash and the rebate rarely stay parallel, and the seal has to take up that movement without splitting. A wooden leaf that rattles in its rebate usually needs the glazing bead refitted before the seal is replaced, because a loose bead lets air past even a brand-new gasket.
We replace weatherstripping in units of any manufacturer, including KBE, Rehau, VEKA and Provedal profiles, and we pick the gasket to match the profile rather than forcing one type onto every frame. The groove width, the depth of the rebate and the way the sash closes differ between systems, so a gasket cut for one profile sits loose or pinched in another. Pavlodar winters swing hard between frost and thaw, and that cycle is what wears the weatherstripping out fastest: rubber stiffens below minus twenty and loses its spring, while a soft compound flattens under the sash and stops pressing back. A gasket that is too soft collapses in the cold and stops pressing on the sash, so the profile and the climate both decide which seal goes in.
The job runs in a fixed order, and the measuring visit decides most of it. Here is what happens from the first call to the moment you check the result yourself.
Measuring and consultation are free, and the measurer comes at a convenient time, takes the sizes and helps choose the gasket, the parts and the fixings for your unit. We reply on WhatsApp within five minutes, so the slot is usually arranged the same day, and the visit takes little of your morning. On site the measurer checks the profile, the sash geometry and the floor level, because those three decide whether a standard strip will sit tight or a different section is needed. The measurer also confirms which part of the frame is actually leaking, so the order you sign matches the real cause rather than a guess made over the phone. Ask to see the sample strip against your own frame before signing — a gasket that looks right on a card behaves differently on a worn rebate.
Most single-unit insulation is finished within a visit, and we work through the cold season because the gasket and the seam can be handled without waiting for warm weather. A framed element made to your size takes ten to fifteen minutes on the bench, a pleated one forty to sixty, and the fitting on site adds the rest of the appointment. Cold air does not stop the strip from seating, though the surface has to be dry and clean before it goes on, which is why the craftsman wipes the rebate first. After the craftsman leaves, close the sash and run a hand along the seam on a windy day, since that simple check shows whether the draught is really gone. If a spot still pulls, note where your palm feels it and call — the first year of repair in Pavlodar covers labour and replaced parts.
A quote means little without knowing what stands behind it. This section sets out the guarantee, the payment terms and the timing you can plan around.
Repair work carries a one-year guarantee covering both the labour and the replaced parts, glass unit replacement carries three years, and installation carries five. The repair cover follows the specific job: if we swapped a gasket or a handle, that part and the fitting of it stay protected for the full twelve months. Glass unit work is tracked separately because the sealed unit is a different component with its own service life, while installation is covered longest since a correctly fitted frame should not move. Because the cover extends to the parts as well as the labour, a failed gasket is replaced under it rather than charged again, so keep the document that lists exactly what was fitted.
You pay after the work is done, by cash, card or Kaspi, and the price is fixed in the order once the measuring visit is complete. Nothing is collected up front: the craftsman finishes, you check the result, and only then does the transaction happen. The measuring visit itself costs nothing, and the figure agreed at that stage is the figure on the order. Kaspi suits residents who prefer to settle by phone rather than carry cash, and card works the same way on the day. Fixing the figure at the order stage means it does not move if the craftsman finds an extra part to replace, so ask for the full list of parts and labour before signing, and keep that list with the guarantee paperwork.
A draughty window is rarely a single fault, and a fix that lasts comes from naming the real culprit before buying anything.
Methods, materials, DIY or a professional, condensation
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionA simple seal replacement can be done yourself if you choose the right rubber profile. But if there are drafts along the seams and the reveals are cold, it's better to call a professional: they will find the cause and fix it without rework.
Besides a new rubber seal around the sash perimeter, the professional adjusts the fitting pressure and seals the seams at the reveals and windowsill. It depends on the window: sometimes the seal is enough, sometimes a full set of warm works is needed.
Adjustment eliminates skew and loose fitting pressure, while insulation is a set of measures: seal replacement, seam sealing, and work on the reveals. They are often done together, but they are different services.
Yes, if moisture appears at the edges due to drafts or cold reveals, insulation often solves the problem. When condensation collects between the panes, the professional will tell you during the free measuring visit whether insulation is enough or a new double glazing unit is needed.
We also insulate wooden frames: we replace the seal, foam and seal the seams, and adjust the sashes. It depends on the window: an old dried-out frame is sometimes easier to replace than to insulate.
Choose a frost-resistant seal with a soft elastic structure that does not stiffen in the cold. It must be selected for your window profile, otherwise the fitting pressure will be loose.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp