Craftsman by a PVC window with a white window reveal in the bedroom
from 4 700 ₸ per linear metreWe protect the seam from sea wind and sun inside and out, and fix the price after the measuring visitCalculate

Window Reveal Finishing in Aktau

Inside · quick

PVC sandwich

Insulated panels cover the foam and resist moisture. From 4 700 ₸ per linear metre.

A technician holds a white piece of sandwich panel for window reveals
GoogleYandex MapsZoon

5,097 reviews on review sites

What window reveal finishing is in Aktau

The sea climate destroys unprotected foam faster than you think

Sea climate

Aktau has plenty of sun and a salty wind from the sea. Exposed mounting foam darkens and crumbles under UV, and the seam starts letting in cold and moisture. The external reveal and sealing protect it from the outside.

Inside we fit PVC sandwich panels, plaster or drywall. On the windy side of the building and in corner flats we additionally insulate the reveal to prevent condensation and mould.

White PVC panel reveals around a plastic window in a bright room
from 4 500 ₸

external reveals per metre

from 4 700 ₸

PVC sandwich per metre

free

measuring visit and selection

5 types
SandwichPlasterDrywallExternalInsulation

How reveal repair is performed in Aktau

Four problems that new reveals solve

Hands tighten a screw near the handle of a plastic window sash
  • 01Exposed foam

    After window replacement the seam is left open. We fit PVC reveals and protect the foam.

  • 02Cracks

    Plaster in the kitchen has cracked from temperature changes. We cover it with sandwich panels.

  • 03Mould

    The corner is damp on the windy side. We insulate and finish it anew.

  • 04Condensation

    The reveal is wet in winter. A warm layer moves the dew point.

Types of reveal work and materials

We select based on the room, wall and side of the building

PVC sandwich

Inside

A technician holds a white piece of sandwich panel for window reveals

Smooth, washable, does not crack.

from 4 700 ₸/linear metre

External

Outside

White plastic window outside the house with neat light window reveals and a grey drip sill

Protect the seam from sun and salt.

from 4 500 ₸/linear metre

Insulation

Cold corner

A craftsman holds an insulation board for window slopes, window slope finishing

Against condensation and mould.

from 19 900 ₸/linear metre

Turnkey

Standard window

Window with finished white reveals in a bright room

Three sides and corner pieces.

from 15 000 ₸/window

Drip sill

Outside

Metal window sill flashing outside a brick house, window slope finishing

Drains water away from the frame.

from 3 250 ₸/linear metre

Window reveal finishing prices in Aktau

Cost per metre or per window, we will give the exact sum at the measuring visit

Type of workPrice
PVC reveals (sandwich panels), per linear metrepanel with insulation insidefrom 4 700₸ per linear metre
Reveals for a standard window, turnkeythree sides and corner piecesfrom 15 000₸ per window
Plastered revealswith levelling and fillingfrom 3 000₸ per linear metre
External revealsprotects the seam from outsidefrom 4 500₸ per linear metre
Drywall revealsready for paintingfrom 1 500₸ per linear metre
Reveal insulationagainst freezing and condensationfrom 19 900₸ per linear metre
PVC windowsill fittingtogether with revealsfrom 5 500₸ per linear metre
Drip sill fittingdrains water away from the framefrom 3 250₸ per linear metre
Sealing internal seams (liquid plastic)joints of frame, reveal and windowsillfrom 1 500₸ per linear metre
Sealing external seamsprotects foam from moisture and sunfrom 2 000₸ per linear metre

Price is fixed in the order after measuringMeasuring is freePayment after work: cash, card, Kaspi

Book a measuring visit

Why customers order reveal work from us in Aktau

Briefly about our work

Experiencesince 2012

we work across Kazakhstan

Response5 minutes

on WhatsApp

Measuringfree

inspection of joint and wall

Pricein the order

does not change

Paymentafter

acceptance

Hours09:00–19:00

no days off

Outsidealso

external reveals and sills

Cities17

cities of Kazakhstan

How window reveal finishing is carried out in Aktau

Work order

  1. A hand holds a phone by the window to measure the opening
    015 minutes

    Request

    Send a photo of the window from inside and outside. We will reply and suggest a time for measuring.

  2. A tape measure measures the window opening next to a plastic window
    02free

    Measuring

    We inspect the joint, wall and side of the house, suggest material and give you the price.

  3. Hands mark a reveal panel with a pencil on a workbench
    03by schedule

    Work

    We cut the foam, insulate if needed, install reveals, seal the joints.

  4. Finished white PVC slopes around a plastic window, window slope finishing
    04in your presence

    Handover

    We check the corners and clean up. Payment after acceptance.

Good to know

Window Reveal Finishing in Aktau

We handle window reveal finishing in Aktau with our own fitters, not subcontractors. A free measuring visit comes first, the measurer takes sizes and picks the material and fixings for your window profile and floor, and you pay only after installation by cash, card or Kaspi. The price is fixed in the order after measuring.

Which window reveal finishing material suits your window best

A reveal is not decoration. It is part of the opening that holds warmth in and closes the joint between frame and wall, so the material you choose decides how it behaves under sun and temperature swings.

Plastic, sandwich panel or plaster — what the difference really is

Plastic and sandwich reveals are ready-made panels fixed over the opening, while plaster is built up on site and needs drying time before it can be finished. A sandwich panel is two rigid skins with insulation between them, which is why it holds shape on a wide opening better than a thin PVC sheet. Plaster gives a seamless wall-to-frame line, but every coat adds moisture that has to leave the room before painting, and a hairline crack returns at the frame joint once the building settles. On a south-facing wall the panel colour matters more than the thickness, because a cheap surface fades long before the panel itself wears out.

Matching the reveal to the profile and the floor

We pick the panel and the fixing to match your profile and the floor it sits on, so the reveal does not pull away after the first hot season. Our measurer checks plastic, wooden and aluminium frames and chooses the fixing for the profile and the storey, because a reveal on an upper floor catches more wind-driven dust at the frame edge — the seal there is checked and renewed rather than reused. Measuring and consultation are free, and the measurer comes at a time that suits you with samples of panel colour and mesh. Before the panels are cut, ask how the frame edge will be sealed, since that joint, not the panel face, is what shows wear first.

How the free window reveal finishing measuring visit and fitting run

The work starts with a measuring visit, not with a sheet of material. How the opening and the sash are measured decides whether the reveal sits tight or leaves gaps along the edge.

What the measurer checks and how a crooked opening is handled

The measurer takes sizes from both the opening and the sash, and the unit stays in place — there is no need to remove it to finish a reveal. Measuring and consultation are free, and the measurer comes at a convenient time, takes the sizes and helps choose the trim, the mesh and the fixings. He checks the width at the top, middle and bottom, because a surface that reads straight on one line can be off by a few millimetres on another. A crooked opening is handled by cutting the sheet to the site after measuring, not by packing the gap. A packed gap reopens as the sealant ages and shows a hairline crack above the opening, so ask for the panel to be cut to the wall rather than shimmed out.

What is included in the work and how the reveal is fixed

  • Removing the old finish: previous trim, foam residue and loose plaster come off first.
  • Insulating and sealing the gap: the space between sash and wall is filled and sealed against heat loss.
  • Fixing to the sash: the sheet sits on a starter profile screwed to the unit.
  • Fixing to the wall: corner pieces and screws hold the outer edge to its own line.
  • Finishing and clean-up: joints are sealed, corners closed and the area cleared the same day.

How long the fitting takes and when you can use the opening

Window reveal finishing in Aktau is done in one visit, and the unit can be used the same day because there is no plaster to dry. A single opening takes a couple of hours once the old finish is off, and a flat with three or four openings is usually a day's work for our fitters. The seal between sash and trim is what stops draughts at the edge, so it is renewed during fitting rather than covered over. A mosquito screen is best fitted after the reveal is in place, so its fixings sit on the finished surface and do not disturb the trim. In our practice, homeowners here who order both together get the screen mounted once the reveal has set, which avoids drilling through a fresh joint.

When a reveal needs finishing and when the window itself needs repair

Cold at the edge of a window does not always mean the reveal is at fault. The job is to work out whether the panel has pulled away from the frame or the sash itself is letting air through.

Reading the signs — condensation, draughts and cracks

  • Condensation on the glass: water beading across the pane points to the window or the room air, not the reveal.
  • Damp line at the edge: a wet strip where the panel meets the frame means the seal behind it has broken down.
  • Draught from under the panel: air moving at the bottom or side shows a gap between panel and opening.
  • Hairline crack at the corner: a crack running from the reveal corner usually means the seal behind it has failed, so filling the crack alone will not stop it coming back.
  • Mould in one spot: dark patches confined to the reveal joint confirm trapped moisture in the gap rather than general damp.

Refinishing a reveal or repairing the window — how to choose

If the panel has pulled away or the seal has gone, we refinish the reveal; if the sash itself lets air through, the window needs repair or adjustment first. We mount reveals with insulation and sealing of the opening, and our fitters check the sash and gaskets before any panel goes back on. Repair work covers adjustment of the sash, replacement of the gasket and the parts that wear out, and we handle it as a separate job from the reveal. Doing the window repair before the reveal is refinished avoids taking the new panel off again to reach the frame. On older aluminium and wooden openings the gasket often fails first, so ask for it to be checked at the same visit.

Reveals for different windows and alongside other work

These panels do not only go on a standard plastic window. Timber, aluminium, balcony doors and loggia glazing each need their own approach to fixing, and the material of the sash decides how the panel is anchored.

Wooden, aluminium and balcony-door openings

We fit reveals on plastic, wooden and aluminium sashes, on balcony doors and loggia glazing, choosing the fixing to suit each one. On aluminium profiles the panel is anchored through the existing screw channels, while balcony-door openings get a reinforced edge because the surface takes knocks from daily traffic. Timber sashes are measured with a small gap left at the top and sides rather than cut flush. Wood moves slightly with the seasons, so the panel there is fixed to allow that movement instead of locking it tight against the timber. Ask the fitter to show you the fixing points on a wooden sash before the panels go on — a reveal screwed hard to a moving surface will crack along the joint within a couple of seasons.

Ordering reveals together with window repair or a new glass unit

Reveals can be ordered in the same visit as repair work, a new seal or a glass unit replacement, so the opening is finished once. We swap seals on units of any manufacturer, including KBE, Rehau, VEKA and Provedal profiles, and can produce and fit a glass unit within one day at a surcharge. Combining the jobs means one set of dust sheets, one measuring visit and a single clean-up instead of two. In a new flat it is worth finishing the reveals before the final wall decoration, so any dust from fitting lands on bare walls. Book this work before the painters arrive, not after — sanding and anchoring always throw up grit that settles on fresh paint.

What you get from a direct fitter and how the deal works

When the people who measure your reveal also fit it, responsibility for the finished result sits with one team instead of being split between a seller and a subcontractor.

Own fitters, a fixed price and payment after installation

Our own fitters carry out the job, the price is fixed in the order after measuring, and you pay once everything is up by cash, card or Kaspi. The measurer records the opening sizes, the reveal material and the type of fixing — Z-brackets, pins or magnets — so the sheet lists every component before anyone drills a hole. Because the same crew that measures returns to install, nobody re-quotes on the day of the visit. Settlement happens only when the reveal is finished and you have checked the joints and edges yourself. The measurer comes whenever suits you, the visit costs nothing, and the figure agreed afterwards leaves no room for add-ons later, since the paperwork already names the material and the fixings.

Warranty cover and how to reach us

Cover and periods for each completed service
Type of workWhat the warranty coversTerm
Window repairLabour and replaced parts1 year
Window installationInstallation5 years
Glass unit replacementThe replacement unit3 years

What to check before ordering window reveal finishing

A sound reveal is settled at the window itself: material, sizes and fixings decided on site, not guessed from a photograph. Here is the short version to carry with you.

  • Material follows the opening: the reveal is chosen for the profile and the side of the building, not by habit or what a neighbour fitted.
  • Measuring comes first: the visit settles sizes, fixings and the shape of a crooked opening, and no panel is cut until then.
  • Two different faults: a draught along the reveal edge and condensation on the glass have separate causes and separate fixes.
  • Wide coverage: reveals suit plastic, wooden and aluminium frames, balcony doors, loggias, porches and gazebos.
  • Sequence matters: finishing the reveal ahead of the final wall decoration keeps dust off fresh surfaces and saves a second clean-up.

Questions about window reveal finishing in Aktau

Reveal finishing, materials, sealing, wet areas, warranty

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01How do you finish the reveals on a wooden or aluminium window?

On a wooden window, plastic or sandwich panels are usually fitted with neat trimming to the frame; on an aluminium one, thin overlays are used so the profile stays visible. The exact option depends on the window and the depth of the opening, and it is chosen during the free measuring visit.

02What should be done if the old reveals are cracked?

Small cracks and peeling plaster are usually repaired, but if the panels have separated at the seams or are coming away from the frame, it is easier to replace them completely. The decision is made after inspection: it is important to understand whether the reveals under the cladding are dry.

03How do you properly seal the joint between the reveal and the window so it does not draft?

The seam is first filled with insulation, then covered with a vapour-permeable tape or sealant, and an overlay is installed on top. It is important not to seal the installation seam completely, otherwise moisture will accumulate inside.

04Which reveals are suitable for a kitchen and bathroom where it is damp?

Plastic panels and sandwich panels are better suited for wet rooms: they are not afraid of steam and are easy to clean. Plaster is used there less often, as it requires protection from moisture and may crack over time.

05How do you finish the reveals on a balcony or loggia in Aktau given the heat and sun?

For a balcony, panels resistant to ultraviolet light are chosen, otherwise the light-coloured plastic will yellow over time on the sunny side. It is also important to insulate the reveal and close the external seams so that there is no overheating in summer and no freezing in winter.

06Is a warranty provided for reveal finishing in Aktau?

We provide a warranty for reveal finishing work, and its terms are fixed in the order after the measuring visit. If gaps appear or an overlay comes loose after installation, please contact us and we will resolve it under the warranty.

Reviews of reveal finishing in Aktau

5,0based on 97 reviews on platforms
All reviews