Technician holding a loop of new rubber window seal on a warm loggia
from 1 000 ₸ per linear metreWe select a seal for your window brand and replace it in one visit, with a 1-year warranty on the work.Calculate

Window Seal Replacement in Aktau

PVC windows · EPDM

Standard seal

Suitable for most apartments: the soft contour presses the sash tightly again and keeps out sand and wind. From 1 000 ₸ per linear metre.

Technician holds a coil of black rubber window seal
GoogleYandex MapsZoon

5,097 reviews on review sites

What a new seal contour in Aktau restores

The frame is still strong, but the seal has given up. A new contour restores the window's tightness in one visit.

Why seals age

The seal in the window grooves works like a gasket: the pressed sash closes the gap, and the wind finds no way in. When the rubber dries out and cracks, the seal is lost, and with it warmth and quiet.

In Aktau the seal has a hard time: summer sun, salty sea air and wind-blown sand dry it out faster than in other cities. The technician selects a seal for your profile and replaces the contour in one piece.

Hand fits a new black seal into the groove of a white sash
from 1 000 ₸

linear metre of new seal including labour

1 year

warranty on replacement and on the new seal

any

window brands: KBE, Rehau, VEKA, Provedal and others

Window brands
KBERehauVEKAProvedalOthers

How seal fitting on windows in Aktau is performed

Four signals most often noticed by apartment owners by the sea.

A palm at the edge of a closed sash checks where the draft comes from
  • 01Rubber has become hard

    Squeeze the seal with your fingers: the old one doesn't spring back but crumbles, and the sash no longer presses against the frame.

  • 02Sand on the windowsill

    If sand lies on a closed window after a windy day, it is getting through the worn contour.

  • 03Cracks in the corners

    The corners of the sash age first: a crack there quickly spreads and lets in cold air in winter.

  • 04Draught along the frame

    Run your hand along the perimeter of the sash on a windy day, and you will feel where the seal is not holding.

Types of seal contours for Aktau windows

The choice depends on the side of the house and the type of frame: German rubber is better for the sunny side, a brush seal for a sliding aluminium window.

Standard EPDM

standard apartment window

Technician holds a coil of black rubber window seal

The rubber keeps its shape in both heat and winter wind, fits most PVC profiles.

from 1 000 ₸/linear m

German

south side, by the sea

A craftsman holds a coil of grey rubber window seal in his hand

Fades more slowly in the sun and stays flexible longer in salty air.

from 1 200 ₸/linear m

Door

loggia, exit to the yard

A length of black self-adhesive window seal on a master's palm, white backing paper peeled back at the end

The seal for a frequently opened sash holds its compression longer than usual.

from 5 000 ₸/pc.

Brush

aluminium sliding

A craftsman holds a strip of brush window seal with bristles in his hand

Dense bristles close the gap at the runners and do not hinder the sash sliding along the frame.

from 1 150 ₸/linear m

Between-frame

windows facing wind and road

A craftsman holds a thin strip of double-glazed window seal in his hand

An extra layer of rubber between the frame and sash reduces noise and draughts from below.

from 2 800 ₸/window

Window seal replacement prices in Aktau

The cost is calculated by the length of the seal and the brand of rubber; the exact amount will be given by the technician on site.

Type of workPrice
New perimeter sealstandard EPDM contourfrom 1 000₸ per linear metre
German sealfor windows on the sunny sidefrom 1 200₸ per linear metre
Window seal kitframe and sash at oncefrom 3 500₸ per window
Balcony door sealfull door contourfrom 5 000₸ per item
Brush seal for aluminium framessliding sashesfrom 1 150₸ per linear metre
Seal cleaning and lubricationfrom sand and saltfrom 750₸ per linear metre
Inter-frame contourthird layer of protectionfrom 2 800₸ per window
Draught detection and eliminationgap along the perimeterfrom 3 500₸ per sash
Sash pressure adjustmentfor the new sealfrom 3 000₸ per sash
Liquid plastic at jointsbead and corner seamsfrom 1 500₸ per linear metre
Wooden frame insulationSwedish technologyfrom 4 200₸ per linear metre

The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi

Send a request

Why customers order seal replacement in Aktau from us

What a window owner gets when ordering work from us.

Warranty1 year

for the work and the new seal we installed

Brandsany

KBE, Rehau, VEKA, Provedal and windows from other manufacturers

Pricein the order

we fix the amount after inspection; it does not change during the work

Paymentafter

checking the window together with you: cash, card, Kaspi

Response5 minutes

usually the wait for a reply on WhatsApp

Daysno days off

we accept requests on weekdays and weekends

Hours09:00–19:00

we work daily within this interval

Experiencesince 2012

we work across Kazakhstan

How seal replacement on PVC windows in Aktau is carried out

Four steps from message to a tightly closed sash.

  1. A hand holds a phone with a dark screen near the edge of a white window
    01reply in 5 minutes

    Request

    Write on WhatsApp and send a photo of the window: you can see where the seal is cracked, fallen out or letting sand through.

  2. A tape measure lies along the bottom edge of the window opening, close-up view
    02at a convenient time

    Inspection

    The technician checks the compression, hardware and profile, selects the seal and gives the price before starting work.

  3. Hands holding a piece of new black window seal above a workbench with tools
    03one visit

    Replacement

    We remove the old seal from the grooves, clean out sand and dust and install the new seal without joints.

  4. Finished white window in a bright room
    04together with you

    Check

    We adjust the sash compression, check the window for draughts, and only then do you pay for the work.

Good to know

Window Seal Replacement in Aktau

We handle window seal replacement in Aktau as a direct contractor with our own fitters, not through a middleman. We replace worn seals on sashes and frames of plastic, wooden and aluminium windows, match the seal to your profile, and back the work with a one-year warranty on labour and replaced parts. Payment comes after installation.

How to Tell a Worn Seal from a Faulty Hinge Before Window Seal Replacement

Most calls that reach us start the same way: it is blowing in, but the sash is shut. The first job is always to separate a tired seal from loose hardware before anything gets swapped.

Five Signs the Seal Has Lost Its Grip

  • Draught at the handle side: cold air creeps along the edge where the rubber has flattened against the frame.
  • Condensation near the perimeter: moisture beads close to the seal line, not in the middle of the pane.
  • Whistling in strong wind: a thin high note means the gap has opened just enough for air to squeeze through.
  • No spring-back: press the strip with a fingernail — a healthy one recovers, a worn one stays dented.
  • Street noise returns: traffic sounds that were muffled before now come through clearly at the edges.
  • Paper test: slide a sheet between sash and frame — if it pulls out freely at any point, the seal is compressed there and turning the handle harder will not close it.

When It Is the Seal and When It Is the Hardware

Our fitters check the hinge side first, because a dropped sash mimics a dead seal but needs adjustment, not new rubber. A sagging leaf drags at the bottom corner, leaves a gap at the top, and the handle turns stiffly or not at all — that is hardware work. A seal fault looks different: the leaf sits square in the frame, the handle turns smoothly, yet air still passes along one edge. We change seals on frames from KBE, Rehau, VEKA and Provedal, so the profile brand never blocks the job. Black spotting that scrubs off with a cloth is surface mould and the strip can stay; growth that has eaten into the rubber and left it crumbly means replacement, since the profile no longer presses tight against it.

What Window Seal Replacement Involves Step by Step

A seal swap is a short job, but the result depends on how the measure is taken and how the part is matched to the profile. The order of the steps matters more than the speed.

From the Free Measure to the Finished Sash

We start with a free measure at a time that suits you, where the measurer takes the profile dimensions and helps pick the seal, then the fitter returns to strip the old rubber and press the new length into the groove. The measure covers the perimeter, the channel width and the corner geometry, because a profile that reads 4 mm on the straight run can sit in a 5 mm groove at the corners. On the return visit the old cord is lifted with a plastic spatula, the channel cleared of grit, and the fresh length seated without stretching. Window seal replacement Aktau jobs on a single casement are done in one pass with no scaffolding. The sash stays on its hinges for a swap, so a single unit is back in service the same visit.

Sash, Frame and the Parts Most Jobs Miss

A seal runs on both the sash and the frame, and we replace both because a new gasket pressed against a flattened strip still leaks at the corners. The moving gasket takes the compression load every time the handle turns; the fixed strip under the rebate keeps the wind out along the perimeter. There is also the mullion joint and the bead line, which a quick swap often skips and which then show up as a draught three weeks later. Our fitter checks both while the unit is open, since these parts cost little against a second call-out. You can book a single casement rather than the whole flat, but if the rubber has gone brittle the rest of the same age usually follow within a season.

Matching the Seal to Your Window Profile for Window Seal Replacement

A seal is not universal: its section and material follow the groove of your profile, so matching starts from the marking rather than from a choice between rubber and silicone.

Which Seal Suits Which Profile

Seal types matched to groove and exposure
Seal typeBest forWhat it handles
Rubber (EPDM)Standard PVC profilesEveryday draughts and temperature swings
SiliconeSunny, hot-facing windowsHeat and UV without hardening
Soft foam-coreLoose or worn groovesFilling a groove the old seal has widened
Brush sealSliding and balcony framesFriction gaps on sliding sashes

Wooden, Aluminium and Balcony Windows

We re-seal plastic, wooden and aluminium frames, plus loggia, gazebo and veranda units, and the seal choice changes with the material because wood and aluminium move differently from PVC. Timber sashes swell and shrink with the seasons, so the seal needs a section that compresses without splitting the groove; aluminium frames expand with heat and call for a firmer rubber or silicone cord that holds its shape. A balcony or veranda frame sits in a colder, damper microclimate than a room opening, so the seal there takes more movement and is worth checking a season earlier than the rest of the flat. On sliding balcony sashes a brush seal handles the friction gap better than a compression cord. If your frame carries a manufacturer mark, note it before the visit — it shortens the match.

Window Seal Replacement and Adjustment in One Visit

Seal replacement and sash adjustment are two different jobs, but they are often needed together. Knowing which one your unit needs saves a second visit and protects the work already done.

Two Jobs, One Fitter

Seal replacement swaps the rubber; adjustment moves the leaf on its hinges to restore even pressure, and we do both in one visit when the diagnosis calls for it. A leaf that has dropped or twisted presses hard on one corner and barely touches the other, so the new gasket never seats the way it should. Our fitter checks the reveal, the hinge side and the locking points before touching the rubber, then sets the leaf so the gap stays parallel along all four sides. We change seals on units from any manufacturer, including KBE, Rehau, VEKA and Provedal profiles. A new gasket fitted onto a leaf that still sits crooked will compress unevenly and wear out early, so the realignment is what protects the seal you just paid for.

If the Unit Still Leaks After the Swap

  • Leaf out of line: a dropped or twisted leaf leaves an uneven gap, and hinge work restores even pressure along the seal.
  • Failed glass unit: fogging between the panes means the sealed unit has gone, and no gasket will fix that.
  • Seal in the wrong groove: a gasket fitted to the wrong section sits loose, so the profile must be matched again.
  • Worn locking hardware: handles and cams that no longer pull the leaf tight let air past even a fresh seal.

Warranty, Payment and Booking the Window Seal Replacement Work

Repair terms differ from the terms on new glazing, and the warranty on the work plus the way you pay are usually what settle the question of who should touch the seal.

What the One-Year Repair Warranty Covers

We give a one-year warranty on repair that covers both the labour and the parts we replaced, so a seal that fails within that year is put right at no extra cost. The same cover applies whatever profile sits in your opening, because our fitters carry seals for KBE, Rehau, VEKA and Provedal systems and work on plastic, wooden and aluminium frames alike. Repair is handled by our own fitters rather than passed to a third party, which keeps the person who did the swap accountable for it. Keep the order sheet the fitter leaves, because the warranty runs from the date on it and the profile and seal section recorded there are what the claim is checked against.

Paying After the Work and Booking a Visit

You pay after installation by cash, card or Kaspi, the price is fixed in the order once the measure is done, and we work seven days a week with a WhatsApp reply inside five minutes. Measuring and consultation cost nothing, and the measurer comes at a time that suits you, takes the sizes and helps pick the seal, fixings and finish for your profile. The main window seal replacement in Aktau that homeowners book most often is scheduled around that visit, so the same trip can cover a draught check on several sashes at once. Booking the measure before the cold snap settles in means the fitter can test the seal against real draughts on the day, rather than guessing at a gap the weather has not yet exposed.

Checks to make before changing the seal

A worn seal is a small component with an outsized effect on draughts, noise and heating bills. The points below sum up what decides whether a replacement holds.

  • Draught with the handle shut: a compressed gasket is the usual cause, but test the hinges first, because a dropped leaf copies the same symptom.
  • Both sides of the join: the seal runs on the moving sash and the frame alike, and swapping one side alone leaves the corners leaking.
  • Profile before section: the seal is cut to fit the groove, so the brand of the unit decides the component, not the reverse.
  • Straighten, then seal: a new gasket on a crooked casement wears out early, which is why adjustment usually travels with the swap.
  • Baseline to ask for: a one-year warranty covering labour and replaced parts, with payment after the work is finished.

Questions about window seal replacement in Aktau

Seal replacement, wear, material choice, hardware adjustment, care

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can the seal be replaced on just one sash or does it need to be done on all windows?

You can replace it on just one sash if the wear is uneven. But if the windows were installed at the same time and the seals have never been changed, it's better to check them all — often the wear is the same.

02How can you tell a worn seal from a good one if it looks intact?

Run your finger along it: an old seal feels hard and doesn't spring back, and may leave marks on your hand. Also check if the rubber sticks to the sash after closing — that's a sign of wear.

03Which seal is best for windows in Aktau given the heat, dust and wind?

For Aktau, an EPDM or TPE seal is suitable — they are resistant to UV and temperature changes. It's also important that the material is flexible and doesn't crack in the heat.

04Why does the window close harder after the seal is replaced?

The new seal is thicker and more flexible, so the sash may close with more effort. The new seal will compress over time, but if it's too tight, it's worth calling a technician to adjust the hardware.

05Does the hardware need adjusting after replacing the seals on plastic windows in Aktau?

Often yes, because the new seal changes the compression. During replacement, the technician checks and, if necessary, adjusts the sashes so the window closes tightly but without excessive effort.

06How should I care for the new seal so it lasts longer?

Wipe the seal with a damp cloth and apply silicone lubricant every six months — it keeps the seal flexible. Avoid aggressive cleaning agents and don't leave the rubber in direct sunlight.

Reviews of window seal replacement in Aktau

5,0based on 97 reviews on platforms
All reviews