Seasonal adjustment
We switch the seal to winter or summer mode so there are no draughts and the gasket doesn't get crushed. Price from 3 000 ₸ per window.


Seasonal adjustment
We switch the seal to winter or summer mode so there are no draughts and the gasket doesn't get crushed. Price from 3 000 ₸ per window.

Hinge adjustment
The sash stops catching on the frame and sagging, and closes first time. Price from 3 000 ₸ per sash.

Draught elimination
We tighten the cams and seal around the whole perimeter and stop the wind whistling. Price from 3 500 ₸ per sash.

Handle replacement
We select a handle to match your profile and fit it in place of the worn one. Price from 2 750 ₸ per item.

Door adjustment
We align the door leaf by hinges and seal, and the door stops catching on the threshold. Price from 6 000 ₸ per item.

5,097 reviews on review sites
Adjusting the seal, hinges and cams without replacing hardware: what the technician does at your home and how long it takes
Window adjustment is setting up the hardware that's already installed: the technician changes the position of the cams, hinges and seal so the sash closes tightly and moves easily again. The parts stay in place.
This work doesn't replace repair: if the locking mechanism is broken or the handle is cracked, parts need replacing. Adjustment restores geometry and seal when the hardware is intact but has shifted over time and with seasonal changes.

simple adjustment of one sash: seal and hinges
the technician adjusts the window at your home in one visit
warranty on window repair: work and replaced components
Five typical window complaints and which hardware component the technician adjusts in each case

When closing, the sash catches on the frame or the neighbouring sash: the hinges are repositioned to align the leaf in the opening.
The mechanism moves with effort or jams: moving parts are cleaned and lubricated, then the cam movement and seal are adjusted.
The door leaf has dropped and catches the threshold: the door hinges and the compression are adjusted so the leaf moves smoothly again.
The sash doesn't engage the strike plates: the hardware is adjusted as a whole, and if parts are worn, their replacement is agreed.
The compression is weaker at the handle or at the hinges: the technician adjusts the cams so the sash presses against the frame along its full height.
Five types of work the technician performs on site, with a guide price per unit
per sash

Adjusting the compression and hinges without removing the sash: suitable when the window closes but draughts.
per sash

The sash is removed, the units are adjusted and put back: needed for severe misalignment of the leaf.
per unit

Adjusting the hinges and compression of the door leaf if the door has sagged and catches the threshold.
per sash

Adjusting the cams and compression in places where air passes near the handle and in the corners.
per sash

Preventive maintenance of moving parts: the mechanism is cleaned and lubricated, the handle moves smoothly.
Services, units of measurement and options: the technician confirms the total after inspecting the window
| Type of work | Price |
|---|---|
| Simple sash adjustmentadjusting the seal and hinges | from 3 000₸ per sash |
| Complex adjustment with sash removalthe sash is removed and refitted | from 4 000₸ per sash |
| Balcony door adjustmenthinges and door leaf seal | from 6 000₸ per item |
| Seasonal winter-summer adjustmentswitching the seal for the season | from 3 000₸ per window |
| Draught eliminationadjusting the cams and seal | from 3 500₸ per sash |
| Window handle replacementselecting a handle to match the profile | from 2 750₸ per item |
| Hardware repairrestoring the locking mechanism | from 7 800₸ per job |
| Opening a jammed sashaccessing the mechanism without damage | from 2 400₸ per sash |
| Comprehensive window servicecleaning, lubrication and adjustment | from 10 000₸ per window |
| Hardware cleaning and lubricationpreventive care of moving parts | from 1 250₸ per sash |
| Micro-lift or extra seal installationadditional sash seal | from 1 700₸ per item |
| Winter slot ventilation installationmicro-ventilation mode | from 7 600₸ per item |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card or Kaspi
Check the cost of workTerms that apply when you order window adjustment
on work and replaced components
we work daily, we agree the visit time in advance
in cash, by card or via Kaspi
in the order after measuring, before work begins
the technician takes measurements and assesses the condition of the hardware
average time to reply to a WhatsApp message
the technician will confirm the earliest available visit time
urgent manufacture and replacement — in a short time
Four steps from request to checking the window in operation

You describe the problem in a message or by phone, the technician confirms the address and agrees a convenient visit time.

On site, the technician inspects the window and agrees with you the scope of work and the time the adjustment will take.

Adjusts the hinges, cams and compression, removes the sash if necessary and lubricates the moving parts.

Together with the technician, you close and open the window, check ventilation and make sure there are no draughts at the handle.
Good to know
We handle pvc window adjustment in Oskemen with its own fitters, not through a middleman. We diagnose the sash, compression and hardware, fix sagging and draughts, and replace seals on windows from KBE, Rehau, VEKA and Provedal. The price is fixed after a free measuring visit, and you pay after the work is done.
A window that catches the frame, drops at the handle or no longer pulls tight is usually an alignment problem, not a dead unit. Here is how to tell the two apart before anyone visits.
We replace parts rather than adjust when the hardware is worn through, the seal has gone flat or hard, or the glazing has failed and fogs from the inside. A hinge that no longer holds its cam position, a gasket that stays compressed after the leaf opens, or a pane with condensation between the layers each points to a different job. A misted double-glazed unit and a perished gasket are separate from adjustment, and we quote them on the same visit so you are not booked twice. Our repair work carries a 1-year warranty on labour and replaced parts, and a new glazing unit carries 3 years. If the leaf still hangs square and only the closing edge leaks, adjustment alone usually settles it.
Adjustment is not a quick turn of a screwdriver before the fitter drives off. It is a sequence of three settings: sash position in the frame, compression tightness, and the way the tilt-and-turn mechanism travels.
A proper adjustment leaves the sash sitting even in the frame, the handle moving without force, and a sheet of paper pinched all round the closed sash with the same resistance at every point. Watch the gap while it shuts — it should stay parallel on all four sides, with no corner dipping. Then open and close in both tilt and turn positions; a mechanism that grinds or needs a second push is not finished. Run the paper test at the corners as well as the middle — a sash that grips at the handle side but slips at the top corner is still out of square and will drop again within weeks.
If air still gets in after adjustment, the fault is usually the rubber gasket rather than the compression. Here is how we tell the two apart before any work starts.
We adjust first and replace the gasket only when the rubber has gone hard, flat or cracked — a strip that still springs back under a fingernail usually just needs the compression set tighter. A flat gasket loses its rebound, the sash closes against a dead surface and cold air travels the whole perimeter instead of one corner. Cracked rubber on the hinge side behaves the same way: it no longer fills the gap when the frame flexes. We press a thumbnail into the strip at three points on each edge and look for a continuous groove where the sash meets the frame. Where the cold enters tells you the job — one edge means the cams are loose, all the way round means the rubber is spent. Replacing a strip that still has life wastes the trip.
| Window brand or hardware | Gasket replacement | Hardware adjustment | What we check first |
|---|---|---|---|
| KBE | available | available | compression and rubber condition |
| Rehau | available | available | hinge wear and cam setting |
| VEKA | available | available | sash square and gasket fit |
| Provedal | available | available | tilt mechanism and gasket |
| Older ROTO fittings | available | where parts allow | part availability before work |
Adjustment is not only a flat-window job. Balconies, gazebos, verandas and private houses put sashes under different conditions, and those panes wear in their own way.
We adjust sashes on balconies, loggias, gazebos and verandas as readily as indoors, and on these the tilt-and-turn hardware and the lower hinge usually take the most wear. A glazed loggia catches wind on both faces, so its hinges work harder than a wall pane that only sees a single side. On summer houses the sash is often opened far more often in warm months and left shut through the cold, which loads the cams unevenly. The lower hinge carries the full weight of the leaf on every such frame, and it is the first point we check for sag. Glazed structures move more with temperature than a heated flat, so their leaves drift out of square faster and benefit from a seasonal check rather than a single fix.
Our fitters travel to private houses and outlying districts of Oskemen and adjust plastic, wooden and aluminium frames, including small vent panes and loggia glazing. A private home usually has more units per visit than a flat, and they sit on different sides of the building, so wind load and sun exposure vary from opening to opening. Small vent panes are adjusted on their own smaller hardware, which most homeowners never touch until the leaf stops closing flush. Wooden and aluminium frames flex differently from plastic, so the fitter checks the frame itself for movement before touching the hardware — adjusting a moving frame only hides the problem for a season.
Booking PVC window adjustment in Oskemen is a short conversation, a single measuring call and one payment at the end. Here is what happens from your first message to the moment the fitter leaves, and what the warranty covers afterwards.
You message us on WhatsApp, we reply within 5 minutes, and the measurer comes at a time that suits you to take sizes, check the window and fix the price in the order before any work starts. Measuring and consultation are free, and the measurer helps you choose the design, mesh and fixings rather than simply writing numbers down. Our own technicians then carry out the adjustment, so the person who assessed the sash is the one who sets the hinges and cams. Because the price is set after measuring rather than over the phone, the figure you agree on is the figure you pay — no add-ons appear once work is under way. Ask for a day when you will be home to watch the check and point out every window that sticks.
Window repair carries a 1-year warranty on both the labour and any parts we replace, and you pay after the work is finished by cash, card or Kaspi. That year covers the setting the technician leaves behind and the hardware swapped during the call, so a hinge that works loose in the first months is our return trip, not a new invoice. We are open seven days a week, which matters when a balcony door starts catching on a Sunday. A window that has just been adjusted usually holds its setting for a year or more, but a sash on a draughty balcony or a door opened dozens of times a day is worth checking each season. Note the date on the order — it starts the warranty and marks when a seasonal check makes sense.
Most window faults that look serious come down to a handful of settings and parts, and the notes below cover what to check before deciding on any work.
Sash sagging, winter and summer mode, scope of work, technician visit
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionYes, a sagging sash is usually realigned by adjusting the hinges, and the catching on the windowsill goes away. If the frame itself has settled or the hinges are worn out, the technician will say what needs replacing — it depends on the window.
The mode changes how tightly the sash is pressed: in winter it is tighter and keeps out the cold, in summer it is looser — the window is easier to ventilate and the seal is compressed less. It is worth switching twice a year, without extra force on the handle.
In addition to setting the hinges and the pressure, the technician checks the seal, lubricates the mechanism and makes sure the sash sits level. If the rubber is worn, it is replaced — this depends on the condition of the window.
A standard sash adjustment is quick, while a complex case involving removing the sash takes more time. The technician adjusts windows one after another, and the time depends on the scope of work.
The pressure is changed with special adjustment screws on the sash, turning them without sudden force. If the handle is stiff or the screws won't budge, it is better not to force it — the mechanism can easily be stripped, and then a technician is needed.
Yes, the technician comes to the home and adjusts the windows on site, visiting around the city. Measuring and consultation are free, and the work and replaced components come with a one-year warranty.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp