Craftsman adjusting a plastic window handle in the bedroom
from 750 ₸ per linear metre of sealWe prepare windows for snow and frost: pressure, lubrication, drainage and seals, payment after inspection.Calculate

Window Maintenance in Oskemen

Before snow · Pressure

Winter mode

We adjust the cams so the sash presses against the seal tighter and cold stays out. From 3 000 ₸ per window.

A hand turns the sash eccentric with a hex key, switching the window to winter mode
GoogleYandex MapsZoon

5,097 reviews on review sites

What window maintenance in Oskemen includes

A set of works after which the window doesn't let in draughts during snowfall, doesn't cry with condensation and opens without effort.

What we do

Winters here are long and snowy, so we start with pressure: switch the sashes to winter mode and check that they press evenly against the seal. The weak spot is immediately visible by the mark on the seal.

Then we clean and lubricate the hardware, treat the seal with silicone so it doesn't harden or freeze, and clear the drainage: meltwater should leave the frame, not freeze in the slots.

A technician wiping the window frame by the handle in a kitchen
from 3 000 ₸

switching one window to winter mode

from 9 000 ₸

finding heat leaks with a thermal imager

1 year

warranty on repair and new components

We check
PressureSealDrainageHingesHandles

How winter window preparation is performed in Oskemen

Four tasks people call us for most often when it's below zero and the wind comes from the mountains.

Serviced window in a study, one handle on the sash
  • 01Window not switched to winter

    We set the cams to tight pressure, and cold air stops coming along the sash edge.

  • 02Mechanisms without care for a long time

    We remove dirt and old grease, apply new lubricant, so the sash and handle move without squeaking.

  • 03Need to go around the whole house

    We check all windows and the balcony door in one visit and note what was done on each.

  • 04Rubber has hardened

    We treat the seal with silicone, and where it is torn, we offer a replacement.

Types of window care work for Oskemen flats

The set depends on the age of the windows and what bothers you: the technician will suggest only what is needed.

Winter pressure adjustment

per window

A hand turns the sash eccentric with a hex key, switching the window to winter mode

We reposition the eccentrics and check that the sash fits tightly all around.

from 3 000 ₸

Finding draughts

per sash

A hand checks with a strip of paper whether air blows from under the window sash

We find the gap where cold air comes in and adjust the sash to it.

from 3 500 ₸

Ventilation mode

per unit

A hand turns the window handle at an angle for gap ventilation

Provides airflow without opening the sash and helps reduce condensation on the glass.

from 7 600 ₸

Rubber and silicone

per linear metre

Hands lubricate the window's rubber seal with silicone using a cloth

We clean and lubricate the seal so it doesn't crack or freeze.

from 750 ₸

Balcony door

per unit

Technician with a hex key by an open balcony door before adjustment

We lift a heavy sagging door and adjust its fit to the frame.

from 6 000 ₸

Window maintenance prices in Oskemen

The total depends on the number of sashes and the works chosen; the technician gives it before starting.

Type of workPrice
Seasonal maintenance (winter/summer)for snowy wintersfrom 3 000₸ per window
Draught eliminationcold at the windowsillfrom 3 500₸ per sash
Hardware cleaning and lubricationsqueaking and stiff movementfrom 1 250₸ per sash
Basic sash adjustment during servicinghinges, misalignmentfrom 3 000₸ per sash
Seal cleaning and lubricationso it doesn't freezefrom 750₸ per linear metre
Winter (slot) vent installationless condensationfrom 7 600₸ per unit
Thermal imaging inspectionfinding cold bridgesfrom 9 000₸ per job
Comprehensive window servicefull set of worksfrom 10 000₸ per window
Apartment window serviceall sashes in one visitfrom 6 600₸ per apartment
Balcony door adjustmentheavy sashfrom 6 000₸ per unit
Window handle replacementnew handlefrom 2 750₸ per unit
Call-out and inspection (without repair order)on-site consultationfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after works: cash, card, Kaspi

Prepare windows for winter

Why customers order window care from us in Oskemen

Conditions that apply to any technician visit.

Warranty1 year

for works and parts we installed instead of old ones

No days offdaily

technicians visit on weekdays and weekends

Reply in WhatsApp5 minutes

on average for a message with a window photo

Pricefixed

we record the amount in the order after measuring and do not change it

Paymentat the end

after checking the windows: cash, card or Kaspi

Profilesany

we work with windows from KBE, Rehau, VEKA, Provedal and other brands

Mesh screenswe remove

we take off mosquito screens for winter and show how to put them back in spring

Experiencesince 2012

we work across Kazakhstan

How window maintenance is carried out in Oskemen

A clear process with no surprises at the end.

  1. A hand holds a smartphone with a dark screen next to a white PVC window
    01reply in 5 minutes

    Request

    You write to us on WhatsApp or leave a request on the website, and we clarify how many windows there are and what is wrong with them.

  2. A tape measure measures the window opening, a hand holds the measuring tape by a white window
    02on an agreed day

    Window inspection

    The technician checks the pressure, hinges, handles, rubber and drainage and gives the price before starting.

  3. Hex keys and lubricant on a table
    03no unnecessary works

    Servicing

    Switches the sashes to winter mode, lubricates the fittings, treats the seal and cleans the frame grooves.

  4. A serviced white window in a dining room, a table in the foreground
    04in your presence

    Check

    You close each sash yourself and check with your hand that no cold comes from the edge, then you pay.

Good to know

Window Maintenance in Oskemen with a Free Measuring Visit

We handle window maintenance in Oskemen with its own fitters, not through an agency. We adjust sagging sashes, replace seals on KBE, Rehau, VEKA and Provedal profiles, swap misted glass units and prepare windows for winter. Measuring and consultation are free, you pay after the work, and repair carries a one-year warranty.

What Window Maintenance Covers and Where It Stops

Window maintenance is not one service but a set of jobs matched to a specific fault. Below we break down what the work includes and where repair ends and replacement begins.

The Four Jobs Behind Most Window Calls

We split the work into four tasks — realigning sashes, renewing seals, repairing hardware and swapping glass — and each one solves a different problem. Realignment corrects a sash that has dropped or rubs against the frame. A fresh gasket restores the rubber strip that blocks draughts, dust and street noise. Hardware work covers handles, hinges and locking points, while a new sealed panel goes in when the double-glazed assembly fogs or cracks. Window maintenance in Oskemen follows the same logic: the fitter first identifies which of the four jobs the fault calls for. Sagging sashes, worn gaskets and loose hinges are the faults our fitters handle most often in Oskemen, and most of them close with a fresh gasket or a realignment rather than a full swap. A stiff handle is usually a lubrication and adjustment job, not a hardware replacement.

When a Repair Beats a Full Replacement

Most units we see need a fresh gasket or a realignment, not a new sealed panel, and renewing the rubber strip alone restores the seal on a window that still holds heat. If the glass itself is clear and only the perimeter leaks, this smaller job keeps your existing frame instead of swapping the whole assembly. A unit that fogs between the panes or shows a crack is a different case — the sealed glass has failed and no amount of adjustment will clear it. Our fitters check both before quoting any work, and the choice between a gasket swap and a full swap rests on one test: condensation inside the panes versus a draught at the edge.

Reading the Window Maintenance Symptom Before You Call a Fitter

Owners describe a fault in plain words: it blows, the sash has dropped, it will not shut. The same complaint can come from several parts, so the description has to become a cause before any work is priced.

Symptom to Cause to Fix

Matching each complaint to its part and action
SymptomLikely causeWhat we do
Draught along the edgeSeal compressed or wornReplace the seal
Frame catches the sashHinges out of lineAdjust the hardware
Fog between panesGlass unit lost its sealSwap the glass unit
Handle turns looselyWorn locking pointReplace the part
Window will not shutSummer ventilation modeReset the hardware

Fault or Just the Wrong Mode

A unit that will not close tightly in winter is often set to summer ventilation mode rather than broken, and switching the hardware back solves it without any parts. The handle on most tilt-and-turn units has a summer position that lifts the leaf slightly off the seal to let air through, and many owners leave it there when the cold arrives. Turn the handle to the fully closed position, then check that the leaf pulls evenly against the frame along its whole height. If one corner still gaps, the gasket has flattened or a hinge has dropped, and that is a repair rather than a setting. Before booking a visit, close the handle fully and watch the leaf meet the frame; if the gap stays, the gasket or the hinges need attention.

How a Window Maintenance Visit Runs and What the Warranty Covers

This section walks through a visit from the first message to the final check, and sets out in plain terms what our warranty actually covers once the work is done.

From First Message to Final Check

We reply on WhatsApp within 5 minutes, book the measurer at a time that suits you, and work seven days a week so a weekend visit is no problem. The measurer arrives at a convenient time, takes exact sizes on site, checks how the frame sits, and helps choose the design, mesh and fixings before anything is ordered. Measuring and consultation are free, and the measurer works from exact on-site sizes rather than from photos. A framed screen made to your size takes 10–15 minutes to produce; a pleated screen runs 40–60 minutes. The price is fixed in the order after measuring, so it does not shift once work starts, and you pay after installation by cash, card or Kaspi. Ask the measurer to note the fixing type in the order — that one line saves arguments later.

What the Warranty Actually Covers

Repair work carries a one-year warranty on both the labour and the parts we replace, and a new glass unit is covered for three years. Installation is backed for five years, and every mosquito screen we make comes with a one-year warranty. That split matters: a failed seal after a repair and a fogged unit after replacement fall under different terms, so keep the order sheet that names the job. Because we are the direct contractor with our own fitters, a warranty claim goes back to the same team that did the work, not to a third party. Photograph the fault before you call — it shortens the conversation and tells the fitter which part to bring.

Windows and Profiles We Take On

We service windows regardless of profile or frame material, from standard plastic units to timber and aluminium joinery. Here is what that coverage means in practice for different types and outdoor structures.

Seals for Any Profile and Any Frame

We replace seals on units of any manufacturer, including KBE, Rehau, VEKA and Provedal, and service plastic, timber and aluminium frames the same way. A worn cord is the most common reason a sash starts to whistle in wind or lets condensation form on the inner glass edge. On timber joinery the gasket sits in a routed groove and is renewed without touching the wood itself; on aluminium systems the fitter matches the profile geometry before ordering the cord. Seal life depends on sun exposure and how often the sash is opened. Check it by closing a sheet of paper in the sash — if it slides out with no resistance, the cord has flattened.

Balconies, Gazebos and Verandas

  • Loggia glazing: sashes on upper floors take strong wind load, so hardware and gasket checks matter before the cold season.
  • Gazebos and verandas: outdoor units face rain and temperature swings, and timber frames often need re-sealing rather than replacement.
  • Wooden windows: loose joints, swollen sashes and worn gaskets are fixed on site, keeping the original wood in place.
  • Seasonal timing: outdoor glazing takes more weather than a flat unit, so a check before each cold season beats one after a leak appears.

Urgent Glass Units and Getting Windows Ready for Winter

A cracked pane and the first hard frost are the two moments when timing decides the outcome. Here is what can be done fast, and what is worth checking before the cold arrives.

A Cracked Glass Unit Within a Day

We can make and fit an urgent glass unit within a single day, which matters when a crack lets cold air and moisture into the frame. A sealed panel holds an insulating gas layer between its panes, and that layer is gone the moment the glass fractures. Moisture then reaches the spacer and the channel, where it freezes, expands and slowly loosens the glazing beads. Tape over the crack keeps out rain but does nothing about the lost fill. Our fitters measure the damaged panel and set the replacement the same day when the order is placed early enough. Booking early protects the wood or plastic from damp.

A Winter Checklist That Actually Helps

  • Seal compression: press a strip of paper into the gap and close the sash — if it slides out easily, the gasket no longer grips.
  • Hardware lubrication: apply a drop of silicone grease to the locking cams and hinges, never plain oil, which collects dust and stiffens in frost.
  • Sash alignment: close the frame and check the gap on all four sides — an uneven line means the hinges need adjusting.
  • Drainage slots: clear the small openings under the opening leaf so meltwater runs outside instead of pooling on the sill.
  • Rubber care: wipe the gasket with a damp cloth and dry it, so grit does not grind into the rubber.

What to consider when ordering window maintenance

Window care is not a single service but a set of jobs matched to a symptom, a frame and a season. The notes below pull the practical points together.

  • Match the job to the symptom: a draught, a sagging sash and a torn mesh each point to a different fix, so describe the fault before booking a visit.
  • Seals and adjustment come first: most calls about draughts or a sash that will not close end with a new seal or a hinge tweak, not a new glass unit.
  • Seals fit any frame: gaskets are replaced on plastic, wooden and aluminium profiles alike, whatever the brand.
  • Fast jobs have their own rules: an urgent glass unit is made within a day, and framed screens come off from inside in a minute for winter storage.
  • Sizes and fixings decide fit: the measurer matches brackets, pins or magnets to the profile and the floor, so the screen sits tight for years.

Questions about window maintenance in Oskemen

Maintenance, seal, hardware, adjustment

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01What does window maintenance include?

The technician checks the sashes and the seal compression, cleans and lubricates the hardware, treats the seal and adjusts the hinges. If worn parts need replacing, this is agreed separately.

02Can the seal be replaced on old windows during a service visit?

Yes, the seal can be replaced on windows from any manufacturer if the profile and sash are intact. New rubber restores tight compression and eliminates draughts without replacing the window.

03How does window servicing differ from window repair?

Servicing is care for a working window: cleaning, lubrication, adjustment. Repair begins when a part has broken or worn out and needs to be replaced.

04How can you tell that window hardware is worn and needs replacing during servicing?

If the handle spins, the sash catches on the frame or the compression cannot be adjusted, the hardware is worn. During the inspection, the technician will say whether adjustment is enough or parts need replacing.

05Can a window be adjusted in winter during a service visit?

Yes, adjustment is also done in cold weather, but the seal is less flexible in frost. The technician will carry out the work carefully and set the compression for winter so the window does not let in draughts.

06Do you service wooden and aluminium windows in Oskemen?

Yes, we service plastic, wooden and aluminium windows, including windows in new buildings. The set of works depends on the design, but we care for the hardware and seal on all types.

07How can draughts and freezing be eliminated without replacing the double glazing?

First, the sash compression and the condition of the seal are checked: often it is enough to adjust the hinges and replace the rubber. If the problem is in the double glazing, the technician will suggest replacing it.

Reviews of window maintenance in Oskemen

5,0based on 97 reviews on platforms
All reviews