Craftsman at a plastic window with a double-glazed unit in the bedroom
from 1 300 ₸The frame stays, only the glass is replaced. We quote the price after measuring and fix it in the order.Calculate

Double Glazing Replacement in Semey

Cold kitchen

Double-chamber

When a single-chamber window is frosty in winter, we install a unit with three panes and two chambers. Price — from 20 000 ₸ per m².

White PVC window in winter, a snowy courtyard outside, a floor lamp and a small table beside it
GoogleYandex MapsZoon

5,097 reviews on review sites

What is double glazing replacement in Semey

If the frame and fittings are in good order, a new window is not needed. We replace the glass unit, and the window is whole, warm and quiet again.

What it is

A unit is glass panes glued along the edge via a spacer into one sealed block. The technician removes the glazing beads, takes out the old unit, places plastic shims and installs a new one made to the measurements of your sash.

In summer Semey can be very hot, and in winter there are severe frosts, so people expect both coolness and warmth from a window. When replacing, it is convenient to choose a coated or double-chamber unit, and for windows by the road — a soundproof one.

Empty PVC window sash against the wall and removed glazing beads on the floor next to a balcony door
from 19 500 ₸

standard new unit per square meter

3 years

warranty on unit and installation

1 day

urgent replacement with a surcharge to the unit price

Types
Double-chamberSoundproofCoatingSingle-chamberTriplex

How glass replacement in Semey is performed

Four reasons people most often contact us from Semey.

A craftsman inserts a white glazing bead into the sash with a rubber mallet
  • 01Glass cracked

    Heat escapes through a crack, and it grows with temperature changes, so the unit is best replaced immediately.

  • 02Fogged inside

    Fog between the panes means the sealant has worn out; such a unit cannot be repaired, we install a new one.

  • 03Window broken

    We make the unit urgently and install it within one day, a surcharge is added to the double glazing price.

  • 04Glass freezes

    We replace a frosty single-chamber unit with a double-chamber one, and the cold from the window noticeably goes away.

Types of glass for a new unit in Semey

You can repeat the old unit, or install a better one: warmer, quieter or cooler in heat.

Double-chamber

kitchen, bedroom, living room

White PVC window in winter, a snowy courtyard outside, a floor lamp and a small table beside it

Three panes and two chambers for frosty winters, frost does not stay on the glass.

from 20 000 ₸/m²

Soundproof

windows by the road

White PVC window high above a busy avenue, a bookcase beside it

Glass of different thicknesses dampens traffic noise noticeably better than standard.

from 19 500 ₸/m²

Coated

country house, sunny side

White PVC window in a home office, a desk with a laptop and a lamp in the foreground

Energy-saving glass reflects heat in summer and keeps warmth in winter.

from 15 200 ₸/m²

Single-chamber

loggia, veranda

White PVC window in a dining room, with an oak table and chairs next to it

A lightweight double-glazed unit for unheated spaces.

from 12 600 ₸/m²

Security film

children's room, ground floor

Hands apply a clear protective film to a window glass with a squeegee

A clear film holds the shards together if the glass does get broken.

from 8 000 ₸/m²

Double glazing replacement prices in Semey

The price depends on the area, the number of chambers and the type of glass; we give the final quote after the measuring visit.

Type of workPrice
Double glazing replacement, per m²standard new unitfrom 19 500₸ per m²
Double-chamber double glazinginstead of coldfrom 20 000₸ per m²
Single-chamber double glazingbalcony, country housefrom 12 600₸ per m²
Coated double glazingenergy savingfrom 15 200₸ per m²
Broken glass replacementafter impactfrom 8 000₸ per m²
Glass in PVC doorbalcony doorfrom 22 000₸ per m²
Security filmchildren's room, ground floorfrom 8 000₸ per m²
Tinting filmcountry house, sunny sidefrom 5 500₸ per m²
Glazing beads extraif old ones crackedfrom 1 300₸ per pc.
Adjustment with sash removalheavy unitfrom 4 000₸ per sash
Window inspection by technicianwithout replacement orderfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi

Send a request

Why customers order a new unit in Semey from us

Terms that apply to every customer.

Warranty3 years

on the new unit and installation work

Paymentafter

installation: cash, card or Kaspi

Measuringfree

we come at a convenient time and help you choose a unit

Pricein the order

fixed after measuring, no surprises

Urgent1 day

production and replacement of broken glass with a surcharge

Response5 minutes

on WhatsApp for a question and a photo of the window

Workingno days off

we take requests every day

Experiencesince 2012

we work across Kazakhstan

How double glazing replacement is carried out in Semey

Four steps from your message.

  1. A hand holds a phone with a dark screen by a plastic window for measuring
    01reply in 5 minutes

    You message us

    Send a photo of the window on WhatsApp and briefly describe what happened. We will reply and suggest a time for measuring.

  2. A tape measure measures the sash opening of a white plastic window, only hands are visible
    02free

    Measuring

    The surveyor measures the glass along the glazing beads, checks the profile and advises which unit to install.

  3. Hands assemble a glass unit from glass panes and an aluminum frame on a workbench
    03urgent — one day

    Production

    The unit is made to measure; if the window is broken, we will make and install it within a day with a surcharge.

  4. A new glass unit is installed in a white plastic window sash, clean glass
    04payment after

    Installation

    The technician sets the new unit on spacers, fixes it with glazing beads and checks how the sash closes.

Good to know

Double Glazing Replacement in Semey

We handle double glazing replacement in Semey with our own fitters, not through middlemen. We replace only the sealed unit and keep your existing frame, fit single or double-chamber units to your profile, and back the work with a 3-year warranty. Measuring and consultation are free, and you pay after installation.

Spotting a sealed unit that is past saving for double glazing replacement

Before ordering a double glazing replacement in Semey, it helps to know what actually failed — the glass pack, the perimeter seal or the hardware. The three look alike from indoors, yet only one calls for a fresh pane.

Five signs the glass pack itself has failed

  • Mist between the panes: condensation trapped inside means the primary seal broke and the desiccant is saturated.
  • A cracked or chipped pane: even a hairline crack spreads with temperature swings and weakens the assembly.
  • Haze or a milky film: moisture entered through the failed edge and settled on the inner surfaces.
  • A draught that survives adjustment: cold air past a correctly adjusted sash points to the perimeter, not the hardware.
  • A loose or distorted pane: the glass has begun to delaminate and no longer sits firmly in its spacer.

When adjustment or a new seal still does the job

We check the hardware and gasket first, because a sash that rubs, whistles or lets in dust often just needs adjusting or a fresh gasket rather than a new one. Our team renews the perimeter gasket on windows from any manufacturer — KBE, Rehau, VEKA, Provedal and others — and re-aligns hinges and locking points during the same visit. A window repair of this kind carries a one-year warranty on labour and replaced parts, so a small fix stays a small fix. If the sash closes flush, holds heat and shows no mist inside, the glass is doing its job and the frame is the place to look. A glazing assembly that has served its span and still fogs after the gasket is renewed is the point where replacement makes more sense than another repair visit.

Replacing the unit with double glazing replacement and keeping your frame

Here we set out when a new glass unit can go straight into the existing frame, and when the frame itself has to be dealt with before any replacement makes sense.

What stays and what changes during a unit swap

We lift out the failed glass pack, clean and check the rebate, seat the new one on fresh glazing beads and restore the seal, so the surround, sashes and hardware stay exactly where they were. The glass pack is the only part that changes. We measure the rebate depth and the thickness before ordering, because a new one has to match the existing profile rather than the other way round. Our 3-year warranty on glass unit replacement covers the sealed unit and its seal, while the frame and fittings keep whatever cover they already had. Because the frame is untouched, the swap avoids the plastering, slope work and re-finishing that a full window change drags in.

Frame condition decides whether a swap is enough

  • Straight rebates: a level, undamaged rebate holds the new glazing panel flat and lets the seal sit evenly on all four sides.
  • Firm corners: press each corner of the sash; movement or a soft spot means the frame will not grip a new insert tight.
  • Working hardware: handles, hinges and locking points that still close the sash square keep the glass under even pressure.
  • No rot or cracks: warped timber, split PVC or a cracked weld will let water in behind the new pane and undo the work.

Choosing a unit for Semey winters and your window

What you pick depends on three things: how cold the space gets in winter, how much depth the frame allows, and whether you need warmth, quiet or both.

Single, double or energy-efficient

Comparing formulas by space and frame capacity
Glazing typeBest forWhat it does
Single-chamberBalconies, utility roomsBasic insulation, lighter weight
Double-chamberLiving rooms, bedroomsHolds warmth through hard frost
Energy-efficientCold-facing rooms, north wallsCuts heat loss and condensation
Sized to existing profileOlder frames with shallow rebateSeats without stressing the sash

Fitting a unit to your frame and size

We measure the rebate depth and the exact opening, then make the glazing to that size, whether the sash is plastic, wooden or aluminium and whether the shape is standard or not. An old wooden block often sits a few millimetres out of square, and an aluminium profile has its own rebate limits, so one specification rarely drops into two windows alike. Non-standard shapes and worn wooden sashes are measured on site rather than from a drawing, because a millimetre of play decides if the pane seats without stress. Our measurer checks the depth before recommending a build — a thicker pack only pays off when the profile can take it, and forcing one in cracks the seal within a season. Units are made to measure at our production, so the size you need is the size you get.

How the double glazing replacement runs from measuring to handover

The job follows a fixed sequence: your first message, a free measure at a time you choose, a price locked in the order, then manufacture, fitting and a joint check before you pay.

From your first message to a fitted pane

  • First contact: we reply on WhatsApp within five minutes and note your window type, size and the problem you see.
  • Free measuring: the measurer comes at a convenient time, takes exact sizes and helps choose the glass, beads and fixings.
  • Fixed price: the figure is written into the order after measuring, so it does not move once work starts.
  • Manufacture: the made-to-measure panel is built to those sizes, not to a nominal one from the label on the existing pane.
  • Fitting: the old panel comes out and the new one goes in, with the surrounding structure left untouched.

Timing, urgent swaps and winter fitting

A standard swap is booked around the made-to-measure panel, and urgent double glazing replacement semey can be done within one day at a surcharge, winter included, because the existing unit stays in place and the room is barely open to the cold. The glazing itself is the only part that travels; sashes, handles and hinges stay where they are, so nothing has to be re-hung or re-aligned afterwards. Cold-weather work is routine for the crews, and a dry, still day is the only condition that really matters. If the forecast turns wet it is worth moving the visit rather than forcing it.

Checking the finished job before you pay

  • Beads: run a finger along each bead; it should sit flush with no gap or rocking under light pressure.
  • Seal: the gasket should run continuous around the whole perimeter, with no stretched or pinched corners.
  • Draught: hold a hand near the joints on a windy day; moving air means the seal needs attention.
  • Payment: settle by cash, card or Kaspi only after the walk-through, and keep the handover sheet with the 3-year warranty terms.

Warranty, care and keeping the new unit dry

A fresh glass pack is only half the story — what happens after handover decides how long it stays clear. Here is what our cover includes and the small habits that keep the glass dry.

What the 3-year warranty covers

We give a 3-year warranty on glass unit replacement, covering the glazing itself and our fitting work, plus a 1-year warranty on window repair that includes labour and every part we swap. The replacement cover follows the product, so if a gasket fails or condensation appears between the panes within that period, the claim is against what we supplied and installed, not against the frame you kept. Repair cover is narrower by design: it runs for a year from the day we finish and covers the parts we fitted and the work we did, which is why the handover note lists both. Keep the order and that note together, because the date and the glass formula written on them are what a claim is checked against.

Simple care that keeps fogging away

  • Wipe with water: clean the pane with a soft cloth and plain water, skipping abrasives and ammonia sprays that dull the surface.
  • Clear the drains: check the drain slots in the frame each season and poke them free, so trapped water runs out.
  • Air the rooms: open windows briefly twice a day in cold weather, which drops indoor humidity and stops condensation forming.
  • Renew the gasket: we replace seals on windows of any maker, KBE, Rehau, VEKA or Provedal, because a hardened strip lets damp air reach the edge.
  • Watch the inside: moisture between the panes means the glazing has already failed, while a wet room-side surface is a humidity issue that ventilation usually solves.

What to look at when choosing a unit for double glazing replacement

A failed glass pack rarely means a failed window, and the decision comes down to reading the signs, matching the glazing to the frame and the climate, then letting a proper measuring visit fix the rest.

  • Failed glass, not a failed frame: fog between the panes, condensation or a cracked pane means the glass assembly is spent, while a sound frame usually only needs the glass swapped.
  • Match the glazing to the window: single, double or energy-efficient glass is chosen by profile depth, room and how hard the local winter bites, not by habit.
  • Free measuring sets the order: the measurer takes true sizes, picks the fittings and fixes the price before anything is made, so nothing is guesswork.
  • Urgent swaps run within a day: a rushed replacement is possible inside twenty-four hours at a surcharge, and payment follows installation, never before.
  • Three years of cover on the glass: the replacement glass carries a three-year warranty, and wiping the seals and keeping the room aired stops fogging from returning.

Questions about double glazing replacement in Semey

Signs of replacement, energy saving, sound insulation, measuring

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01How can I tell that a double glazing unit has lost its seal and needs replacing rather than window repair?

The main sign is condensation or moisture between the panes: the seal around the unit no longer keeps it airtight, and window repair will not help here. Unlike fogging on the outside or along the sash, this condition requires replacing the double glazing unit.

02What is the difference between an energy-saving double glazing unit and a standard one?

A low-emissivity coating is applied to one of the panes, reflecting heat back into the room and reducing cold penetration in winter. Visually, such a unit looks no different, but it keeps the apartment noticeably warmer than a standard one.

03Which double glazing unit best blocks street noise in Semey?

Units with different glass thicknesses and a sufficient air gap dampen noise better than those with simply more chambers. The exact configuration for your noise level will be selected during the measuring visit.

04Can a double glazing unit be replaced in winter at sub-zero temperatures?

Yes, replacement is carried out in cold weather too, provided there is no severe frost or precipitation. The unit is brought in carefully, installed quickly, and the fit is checked immediately so the window does not get cold.

05How is a double glazing unit measured by the frame or by the sash and who does it?

The measurer takes dimensions according to the inner dimensions of the sash or frame where the unit fits, taking the glazing bead into account. They visit for free and help choose the right option for your window.

06Is measuring for a double glazing unit free?

Yes, measuring and consultation for replacing a double glazing unit in Semey are free. The measurer will come at a convenient time, take dimensions, and help choose the right unit for your window.

Reviews of double glazing replacement in Semey

5,0based on 97 reviews on platforms
All reviews