Sash lifting
We adjust the hinges so the sash closes again without lifting by hand and no longer rubs the frame. From 3 000 ₸ per sash.


Sash lifting
We adjust the hinges so the sash closes again without lifting by hand and no longer rubs the frame. From 3 000 ₸ per sash.

Window handle
We tighten a loose handle and replace a cracked one with a new one from 2 750 ₸ per item.

Balcony door
We lift a door that catches the threshold and set the seal against the frame. From 6 000 ₸.

Draught at the window
We find the gap where the wind blows through and close it by adjusting the sash. From 3 500 ₸ per sash.

Mechanism cleaning
We remove dust from the strips and pins and lubricate the joints so the handle moves smoothly. From 1 250 ₸ per sash.

5,097 reviews on review sites
A small adjustment once a year saves you from draughts, stiff handles and expensive repairs later.
Sharp swings from summer heat to winter wind make the frame move, while the sash is opened and closed every day. After a couple of seasons the hinges sag, the handles work loose, and the sealant at the window sill cracks.
During a service visit, the technician catches this early: tightens and aligns the sashes, adjusts the balcony door, cleans and lubricates the mechanisms, treats the rubber and renews the seam. A window doesn't need repair if it is adjusted in time.

cleaning and lubrication of one sash mechanism
care for all windows in the flat
warranty on work and new parts
Four common situations people from Semey contact us about.

We set the winter seal, and on a cold windy day there is no longer a draught along the windowsill.
We clean out old dirt and apply fresh lubricant, so the handle turns without effort.
In one visit we go through all windows and the door so you don't have to call a technician every six months.
We treat the seal with silicone, show you any tears and replace them separately.
The technician will suggest only what your windows need and quote the price for each job.
per sash

We lift a sagging sash and even out the gaps around the whole perimeter.
per item

We replace a cracked or spinning handle with a new one to suit your profile.
per item

We adjust the door so it no longer catches the threshold and closes tightly.
per sash

We clean dust from the hardware and lubricate all moving parts of the sash.
per sash

We find where the draught comes from and adjust the sash so the gap closes.
The total depends on the number of sashes and the jobs chosen; we quote it before we start.
| Type of work | Price |
|---|---|
| Basic sash adjustment during servicingsagging on hinges | from 3 000₸ per sash |
| Window handle replacementold one cracked | from 2 750₸ per item |
| Balcony door adjustmentrubs against the frame | from 6 000₸ per item |
| Hardware cleaning and lubricationafter renovation | from 1 250₸ per sash |
| Draught eliminationdraught along the edge | from 3 500₸ per sash |
| Seasonal maintenance (winter/summer)seasonal mode setting | from 3 000₸ per window |
| Seal cleaning and lubricationrubber after winter | from 750₸ per linear metre |
| Comprehensive window servicewhole window | from 10 000₸ per window |
| Window service for the whole flatall rooms | from 6 600₸ per flat |
| Winter (slot) ventilation installationgentle air flow | from 7 600₸ per item |
| Thermal imaging window inspectionfinding cold spots | from 9 000₸ per job |
| Call-out and inspection (without repair order)advice without repair | from 3 600₸ per job |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after the work: cash, card, Kaspi
Book a technicianA quick look at how we work with windows in Semey.
on window repair: work and replaced parts
after you have checked the windows: cash, card, Kaspi
the usual wait for a reply on WhatsApp
after measuring, the amount is locked in the order
the technician will come on a weekday or at the weekend
we replace seals for KBE, Rehau, VEKA, Provedal and others
we make mosquito screens in Almaty and fit them in Semey too
we work across Kazakhstan
Step by step, from message to handover.

Describe what is wrong: a stiff handle, a draught, a door rubbing the threshold. A photo of the window helps the technician prepare.

The technician checks the hinges, handles, compression, rubber and seams and quotes the price for each job in advance.

Aligns the sashes and door, tightens or replaces handles, cleans the mechanisms and renews the sealant.

You open the windows in all modes yourself, close the door and only then pay.
Good to know
We handle window maintenance in Semey with our own fitters, not through middlemen. We repair and adjust plastic and wooden windows, replace seals on any profile and swap glass units, including same-day jobs. Measuring and consultation are free, the price is fixed in the order after measuring, and repair work carries a one-year warranty.
Almost any window that draughts, mists up or catches on the frame can be repaired rather than replaced. Below is how to tell a worn component from a case that genuinely calls for a new unit.
We check the seal first, because a flat or cracked gasket lets air and moisture past the sash and mimics a failing glass unit in most calls we take. The gasket runs the whole perimeter and takes the wear from every opening and closing, so it hardens and flattens long before the casing does. A simple test on a windy day is to run a hand slowly along the frame: if the draught follows the perimeter, the seal is the suspect, while a cold patch in the middle of the pane points to the glazing. Mist trapped inside the glass is a separate matter and always means the unit, not the frame. Reading the two apart saves an unnecessary swap, and window maintenance in Semey starts with that check.
A visit opens with a free measuring call and closes with every sash tested by hand. Below is what the fitter does step by step, where the job stops, and how long each stage takes at your home.
A maintenance visit covers adjustment, seal replacement, hardware checks and glass swaps, while full frame replacement or fresh glazing is quoted as a separate job after measuring. Seals are matched to KBE, Rehau, VEKA and Provedal profiles, and urgent pane work is completed within one day at a surcharge to the part itself. Our fitters handle the same upkeep in Semey that they measure, so nothing passes to a third party between the call and the handover. Frame replacement means a fresh opening, sashes and a full installation, so it is priced and scheduled apart from routine upkeep. Because we work with our own fitters rather than subcontractors, the person who measures is the person responsible for the result.
The seal is the part most often replaced when a window starts to whistle or let in cold air. Below is how long a gasket lasts and why the frame system decides which material goes in.
A window seal typically lasts several seasons before it flattens, hardens or pulls away at the corners, and the first sign is usually a draught or a whistle along the sash rather than visible damage. Rubber strips on modern plastic, wooden and aluminium frames sit compressed against the sash for years, so they lose elasticity gradually. Draughts near the handle, condensation on the inner edge and dust streaks along the rebate all point to the same worn strip. Press a fingernail into the rubber; if the mark stays instead of springing back, the material has lost its memory and will keep leaking air even after the sash is adjusted.
| Frame system | Seal fit | What we check |
|---|---|---|
| KBE | matched to groove | gasket depth and corner joints |
| Rehau | matched to groove | sash pressure and draught line |
| VEKA | matched to groove | seal memory and contact line |
| Provedal | matched to groove | sliding channel and brush wear |
A sealed glass unit is replaced separately from the frame, so a cracked or misted pane does not mean a new window. Below is how the swap runs and how fast it can happen.
We swap the glazing inside the existing opening, so the frame does not come out and the wall and slopes stay untouched during the job. The old pane is measured against the opening, not against its own dimensions, because a profile settles and shifts over the years. We lift out the beading, take the sealed glass clear, seat the new one on fresh setting blocks and refit the trim. The surround itself stays where it is, and no plastering or painting follows the visit. The opening is measured again before the new glazing is ordered, because a panel cut to the old size can sit loose in a sash that has shifted. Ask for the measurement to be taken with the sash closed and locked.
A cracked or misted panel can be made and fitted within one day on a rush order, which carries a surcharge on top of the standard glass unit price. The workshop cuts and seals the panel to the measured size, and the fitter returns the same day to set it in place. Standard replacement runs on the usual schedule; the rush slot exists for panes that have cracked through, lost their seal or started fogging between the sheets. A crack that runs from the edge spreads faster in cold weather, so a pane replaced before the first hard frost usually avoids a second call-out for the same opening. If the inner sheet is already hazy from condensation, the desiccant is spent and no amount of wiping clears it.
Adjustment and safety fittings solve two different jobs: one keeps the leaf tight against the frame, the other stops a child opening it too far. Below is what you can correct yourself and what our warranty covers.
A leaf that rubs lightly at the top can often be brought back with the adjustment screws on the hinges, but a dropped leaf or one that will not latch usually needs a fitter to reset the hardware. The screws sit on the lower and upper hinge arms: a quarter turn on the horizontal screw shifts the panel sideways, while the vertical screw lifts or lowers a corner. Work on one corner at a time and close the leaf after every turn. Turning the screws without checking level can pull the frame out of square. If the handle turns but the panel stays loose, the fault is in the locking points, not the hinges.
Repair work carries a one-year warranty on labour and replaced parts, glass unit replacement is covered for three years and installation for five, and you pay after the work is done by cash, card or Kaspi. That twelve-month term covers both the fitter's time and any new seal, hinge or handle fitted during the visit. The price is fixed in the order after measuring, so the figure agreed at the visit does not move if the job takes longer than expected. If a worn hinge or a tired seal turns up once the sash is opened, the fitter shows the part and adds it to the order before any work starts, so nothing appears on the bill unannounced.
A window rarely fails all at once. Most calls trace back to a single tired component, and reading the symptom correctly is what keeps a small fix from turning into a full replacement.
Diagnostics, adjustment, seal, double glazing
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionEven on a window that seems fine, the technician checks the seal pressure around the frame, how smoothly the sash moves, the condition of the lubricant in the mechanism and the elasticity of the seal. This catches small issues that turn into draughts after a season.
One visit a year is enough, preferably before the heating season. If the window is in the kitchen or opened often, the seal pressure is checked more frequently. The technician will suggest a precise schedule after inspecting your windows.
Over time the rubber dries out and loses its elasticity, and the mechanism gradually loosens from daily opening. Often adjusting the seal pressure and caring for the seal is enough, but cracked rubber is better replaced. An inspection will show what applies to your case.
If the sash closes but moves stiffly, lets in draughts around the frame or the handle sticks, adjustment and care are usually enough. Replacement is needed when the profile or the double glazing itself is damaged, and the technician will determine this during the inspection.
Minor seal pressure adjustment and lubricating the hardware can sometimes be done by hand if you have the tools and understand the design. But if the sash is skewed or the handle sticks, it's better to call a technician: a failed adjustment increases wear on the mechanism.
Yes, usually all of this is done in one visit: first the sash is adjusted, then the rubber around the frame is replaced and, if needed, new double glazing is fitted. The technician will confirm the exact scope after inspection, as it depends on the window.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp