Technician holding a new white PVC window handle in a bedroom
from 3 000 ₸ per sashSash adjustment takes up to an hour, we will arrange the technician's visit at a time that suits youCalculate

Window Repair in Kokshetau

Draught from under the sash · compression

Sash adjustment

Simple adjustment without removing the sash — from 3 000 ₸ per sash. The technician will check the compression around the perimeter and the eccentrics.

A craftsman holds an L-shaped steel hex key for adjusting hinges
GoogleYandex MapsZoon

5,097 reviews on review sites

What window repair in Kokshetau is and when it is needed

Repair restores the window's working properties: compression, sash movement and contour tightness, without replacing the whole unit.

How the service works

Repair covers work with hardware, hinges, handles, seals and double glazing. The technician adjusts mechanisms, replaces worn parts and restores the sash compression against the frame.

Before starting work, the technician inspects the window: checks compression around the perimeter, the condition of hinges and handle, the integrity of the seal, sash movement and absence of catching, and also assesses the double glazing for fogging and cracks.

Technician in a dark blue T-shirt with a hex key at an open white PVC window sash
1 year

Warranty on window repair: work and replaced components

3 years

Warranty on double glazing replacement after installation

5 years

Warranty on window installation if the unit was replaced

6 services
AdjustmentSealHingesHandlesDouble glazing

How window restoration is performed on site

Six common reasons why a window loses its seal, catches the frame or lets air in. For each, the technician identifies the unit and the way to fix it.

Close-up of an L-shaped hex key in the trunnion on the edge of an open white PVC window sash
  • 01Draught in one corner of the sash

    The cause is wear of the sealing contour: it hardens or loses elasticity. The technician will assess the condition of the seal and the pressure in this area.

  • 02The window won't close

    The hardware has shifted or worn out. The mechanism needs adjustment, sometimes parts replacement.

  • 03The sash has sagged

    The hinges have worn, and the sash catches the frame in the lower corner. Adjustment or hinge replacement helps.

  • 04The handle is broken

    The handle doesn't turn or spins. We replace it with a new one — from 2 750 ₸ per piece.

  • 05Condensation on the reveal

    Moisture and mould appear when the seal is broken and the reveal freezes. Adjustment, seal replacement and insulation are needed.

  • 06The double glazing has cracked

    Fogging from inside or a crack in the glass requires replacement. We replace the double glazing — from 19 500 ₸ per m².

Types of window repair work and technician tasks

Price list items with unit prices: from sash adjustment to double glazing replacement and mosquito screen repair.

Hinges

upper or lower

A craftsman holds an L-shaped steel hex key for adjusting hinges

Replacement of the hinge when the sash sags and catches the frame.

from 4 750 ₸/pc.

Hardware

repair or set

A craftsman holds a new white plastic window handle for replacement

Repair of the mechanism or complete replacement of the set on the sash.

from 7 800 ₸/job

Seal

KBE, Rehau, VEKA, Provedal

Technician holds a roll of grey rubber seal, showing it for replacement

We replace the contour seal on windows of any manufacturer.

from 1 000 ₸/linear m

Mosquito screen

mesh and fixings

A craftsman holds a roll of gray mosquito netting for repair

Repair of torn mesh and replacement of fixings on the screen.

from 2 500 ₸/pc.

Double glazing

by size and formula

A craftsman holds a small square double-glazed unit sample for replacement

Replacement of fogged or broken double glazing and glass.

from 19 500 ₸/m²

Window repair prices in Kokshetau

The price is fixed in the order after measuring, payment — after installation.

Type of workPrice
Visit and inspection by a technicianwithout ordering a repairfrom 3 600₸ per job
Simple sash adjustmentwithout removing the sashfrom 3 000₸ per sash
Complex adjustment with sash removalwith removal and rehangingfrom 4 000₸ per sash
Window handle replacementwith a new handlefrom 2 750₸ per item
Hinge replacementtop or bottom hingefrom 4 750₸ per item
Hardware repairwithout replacing the setfrom 7 800₸ per job
Sash hardware replacementfull setfrom 10 000₸ per sash
Seal replacementalong the sash perimeterfrom 1 000₸ per linear metre
Double glazing replacementby size and specificationfrom 19 500₸ per m²
Broken glass replacementglass without framefrom 8 000₸ per m²
PVC window sill installationwith on-site cuttingfrom 5 500₸ per linear metre
Window reveal installationexternal revealfrom 3 250₸ per linear metre
Mosquito screen repairmesh and fixingsfrom 2 500₸ per item
Air valve installationfor air supplyfrom 6 000₸ per item

The price is fixed in the order after measuringMeasuring and consultation — freePayment after installation: cash, card or Kaspi

Check repair cost

Why customers order window restoration from us in Kokshetau

Guarantees, timelines and service geography — facts we confirm with a contract and order.

Repair warranty1 year

For work and replaced components

Double glazing warranty3 years

For double glazing replacement after installation

Installation warranty5 years

For window installation if the unit was replaced

Urgent double glazing1 day

Manufacture and replacement with a surcharge

Sealany brand

KBE, Rehau, VEKA, Provedal and others

Free measuringwith visit

The measurer will come at a convenient time and advise

Coverage17 cities

You can order in 17 cities of Kazakhstan

Experiencesince 2012

We work across Kazakhstan

How window repair is carried out in Kokshetau

Four steps from request to sash check

  1. A hand holds a smartphone with a dark screen near a white PVC window
    01within 5 minutes

    Request

    You write on WhatsApp — we reply within 5 minutes. We agree on a convenient time and clarify what is bothering you.

  2. A tape measure measures the lower edge of the window opening of a white PVC window
    02on site

    Inspection

    The technician checks the seal, hinges, handle and seal. Determines the cause and names the way to fix it.

  3. A removed white window sash on a workbench next to a coil of new black seal
    03by scope

    Work

    Adjustment, replacement of parts or seals are done on site. The price is fixed in the order after measuring.

  4. A finished white PVC window with a new seal and handle, the sash closed evenly
    04together with the owner

    Check

    We check the sash movement and the seal around the perimeter together with you.

Good to know

Window Repair in Kokshetau with Our Own Crews

We handle window repair in Kokshetau with our own crews, not through middlemen. We fix plastic, wooden and aluminium windows, replace seals and glass units, and adjust hardware that has dropped or stopped sealing. Measuring and consultation are free, we work seven days a week, and every repair carries a one-year warranty on labour and replaced parts.

What Your Window Repair Is Telling You and What It Usually Means

A window rarely fails all at once; it signals first through a draught, condensation or a sash that drags. We read each symptom for what it points to and the repair that follows.

A Draught from a Closed Window and Where It Comes From

A draught from a shut window almost always traces to one of three points — a hardened seal, a loose sash clamp, or hardware that no longer pulls the panel tight against the frame. Rubber is the usual suspect: it loses its spring over years of frost and temperature swings, flattens and lets cold air slip past. The clamp wears where the handle drives the locking cams, so the panel sits a fraction off even when the handle turns fully. Run a hand along the gasket on a cold day; if it feels stiff rather than springy, it has aged out and no amount of handle-turning will close the gap. We replace the rubber and adjust the clamp together, because a fresh gasket over worn hardware only half-solves the problem. When a window repair in Kokshetau is needed, we trace the draught to its source before touching the seal.

Why Windows Sweat and Frost Up in Northern Kazakhstan

Condensation on the glass is normal in a sharp continental climate, but water pooling on the frame or ice forming at the edges points to a broken gasket or a clamp that no longer presses the panel home. Kokshetau winters swing hard between −30 °C nights and warmer daytime air, and that spread drives moisture onto the coldest surface in the room. A sound glass unit handles the swing; a failed perimeter seal lets warm indoor air reach the cold edge, where it condenses and then freezes. The fix is rarely the glass itself — restoring the clamp and rubber usually stops the sweating, while replacing a sound unit only hides the cause. Check the bottom corners first, where water collects before it reaches the sill.

A Dropped Sash That Catches on the Frame

When a sash drops and scrapes the frame, the cause is worn or misaligned hardware, and in most cases we bring the geometry back with adjustment rather than a new panel. Hinges carry the full weight of the moving part for years, and the lower corner slowly sags until it rubs on closing. The handle and locking mechanism add to it: a cam that no longer seats evenly pulls one side tighter and racks the panel out of square. Adjustment restores the geometry by re-setting the hinges and re-tuning the clamp, and the panel closes cleanly again. Catching sashes wear the gasket and the hinge points faster the longer they are left, so a slight rub today becomes a hardware replacement if ignored through a season. We check the whole mechanism, not just the rub point.

Window Repair or Replace and How to Draw the Line

A full swap costs more and takes longer than a repair, so the decision should rest on the parts that actually failed. Below is how a master reads the signs and where the line between the two routes usually falls.

When a Window Is Still Worth Repairing

A unit is worth repairing when the frame and the glass unit are sound and the fault sits in the seal, the clamp or the hardware — the parts we replace and adjust on a normal visit. We regulate the hinges, handles and locking mechanism, swap worn seals and re-set the sash clamp so the leaf pulls tight against the profile again. A frame that is still square and a sealed unit that is not fogged inside are the two signs that repair will hold; if either is gone, adjustment buys time but not a fix. On most calls the whole job stays within one visit, and our one-year repair warranty covers both the labour and the parts we fit.

The Signs That Point to Replacement

Replacement makes sense when the frame itself is warped, the glazing has fogged between the panes, or the profile has cracked — faults that no adjustment or seal swap can reverse. A sealed unit is two or more panes sealed around a gas-filled chamber, so once moisture gets inside that chamber it stays there. That is the clearest single signal, because cleaning or resealing the surround will not clear the haze between the panes. A sash that has lost its geometry also resists repair: it will keep catching or dragging even after new hardware goes in. When several of these faults stack on the same opening, the money is better spent on a fresh unit than on repeat visits.

Comparing Repair and Replacement Side by Side

what each route touches and leaves behind
What changesRepairReplacement
FrameStaysNew
Glass unitSwapped if foggedNew
Seal and hardwareReplaced or adjustedNew
Time on siteOne visitFull install
Warranty1 year on repair5 years on install

The Window Types and Jobs We Take On

Units around the city are not all alike — panel blocks, private houses, loggias and old timber frames each ask for different work. Here is what we repair on each type and which jobs fit into a single visit.

Plastic, Wooden and Aluminium Units We Repair

We repair plastic, wooden and aluminium frames, and the job changes with the material — plastic takes adjustment and gasket swaps, wood takes refinishing and hardware work, aluminium takes hinge and locking-point attention. On PVC units the usual tasks are resetting a dropped leaf, replacing the rubber strip and re-tensioning the locking points. Timber frames from older houses get sanding, fresh paint and new putty around the glass, plus hinge and latch repair. Aluminium systems in loggias and offices mostly need hinge replacement, pressure adjustment and re-sealing at the joints. Old timber frames in private houses here are often worth saving because the wood is thicker than modern profiles, so refinishing and re-sealing can outlast a cheap replacement.

Seals, Hardware and Glass Units in One Visit

A single visit can cover a gasket swap, hardware adjustment and a glass unit replacement, and we change the rubber strip in units of any make, including KBE, Rehau, VEKA and Provedal profiles. This strip is the cheapest part of the job and the first to fail — it hardens, shrinks and stops pressing against the frame. Hardware work means new hinges, a fresh handle or a re-set locking bar, and the double-glazed panel is swapped when the sealed chamber has fogged or cracked. Replacing only the rubber strip is often enough when the frame and the clamp are sound, but a new gasket on a mechanism that no longer presses will not stop the draught.

Balconies, Loggias and Cold Rooms

Glazing on balconies and loggias takes the same repair as indoor ones, but the colder, damper conditions there wear gaskets faster, so we check the clamp and rubber seal with extra care. Units on an unheated loggia work in a wider temperature swing than a living-room one, and the gasket on such frames stiffens sooner. Cold rooms and summer verandahs in private houses get the same treatment, with attention to the lower hinge, which collects moisture. A balcony unit that sweats heavily is often telling you the room behind it is under-ventilated, so fixing the seal without improving airflow just moves the moisture to the wall.

How a Visit Runs and How to Check the Result

A good repair is not a case of tightening a screw and driving off. It is a clear sequence of steps and a check you can see for yourself on site.

From First Message to the Master at Your Door

You message us on WhatsApp, we reply within five minutes, and the measurer comes at a time that suits you, takes sizes and helps choose the fix before any work starts. Measuring and consultation are free, so the first visit costs you nothing but the half hour it takes. The measurer inspects the profile, the fittings and the gasket, then writes down what the job needs. Sending a photo of the unit with the first message usually saves a second trip, because the technician can load the right part on the first visit. In our practice, a clear photo of the handle and the hinge side is worth more than a long description — it tells the crew which fitting to bring.

What the Master Actually Does on Site

On site the technician tests the clamp, the gasket and the hardware, adjusts or replaces what has failed, and finishes by confirming that the sash closes tight and the handle turns without force. A sash that catches, a draught along the hinge side and condensation on the rubber all point to the same small set of parts: the clamp, the gasket and the moving hardware. A proper adjustment is measured, not guessed — the gap between sash and frame is checked at several points, because a clamp that is tight at the handle can still leak at the far corner. Swapping a worn gasket takes minutes and restores the barrier that keeps cold air and street noise out.

How to Check the Work Before the Master Leaves

  • Paper test: trap a sheet at the handle side, the hinge side and the corners; resistance should feel the same everywhere.
  • Handle check: it should turn smoothly and lock without a hard push at the end.
  • Gasket check: run a finger along the rubber; it should feel springy, not hard or flattened.
  • Frame check: look for daylight or a visible gap between sash and frame when the unit is shut.
  • Draught check: on a cold day, hold a hand near the hinges and the sill corners where leaks hide.

Timing, Payment and How to Book a Master

Timing and payment terms often decide whether a repair is booked now or postponed again. Here is how long a swap takes, how the price is fixed, and when you actually pay.

How Fast a Glass Unit Can Be Swapped

We can make and fit a replacement unit within a single day when the job is urgent, with a surcharge on the price; a standard swap is scheduled on a normal visit. The urgent route exists because a broken pane in a heated room drains warmth fast, and waiting a week for a slot is not always realistic. A fogged panel that still holds its seal is a different case — the glazing is failing inside but the room stays warm, so a scheduled call works fine. On the day itself the old assembly comes out and the new one goes in during the same appointment, with the frame cleaned and the seals checked before the master packs up. A same-day swap is worth asking for when a pane is cracked and heat is escaping, but a fogged unit that still seals can wait for a scheduled visit without harm.

How the Price Is Fixed and When You Pay

The price is fixed in the order after measuring, and you pay after the work is done — by cash, card or Kaspi — so nothing is settled before you have seen the result. The survey step is where the number is set: the specialist records the frame dimensions, the profile type and the glazing build, and that figure goes into the order as final. Payment follows the finished job, which means the master leaves with the glazing working and the invoice matching what was agreed. Fixing the price after the survey protects both sides, because the master has seen the actual unit and the customer is not quoted on a guess that changes on site.

Booking a Visit Any Day of the Week

We are open seven days a week, so a visit can be booked for a weekday or a weekend, and the measurer comes at a time that fits your schedule. That flexibility matters when both adults in a household work daytime hours and the only free slot is Saturday morning. Booking the survey early in the week leaves room to schedule the actual repair before the weekend, which matters most when a pane is letting in cold air. A quick message is enough to start — we reply on WhatsApp within five minutes during working hours. The site visit and consultation are free, and the specialist brings the sizes back so the order can be confirmed without a second trip.

Warranty and What Stands Behind the Work

A warranty is what separates a proper repair from a one-off patch job. Here is what our cover includes, how long each part is protected, and why a direct contractor answers for the work differently than a middleman.

What Our One-Year Repair Warranty Covers

Every window repair carries a one-year guarantee on both the labour and the parts we replace, so if the same fault returns within twelve months, we come back and put it right. That single term covers the seal we swap, the hardware we adjust and the hands that fitted them: a sash that starts catching again, a handle that works loose, a draught that reappears along the same edge. The cover is written into the order, not agreed over the phone. Naming both labour and parts matters, because a fault can come from the fitting or from the component itself, and protection covering only one leaves the other on you. Ask any contractor to state both in writing before the master starts.

Longer Cover on Glass Units and Installation

A replaced glass unit carries a three-year guarantee, and a full installation carries five years, so the cover matches how long each part is expected to last. A sealed unit either holds its seal or fails early, which is why three years is a fair test of the factory edge and the spacer inside it. Installation gets the longest term because the frame, the anchoring and the foam line are fixed once and should not move for years. The repair term, by contrast, covers moving parts that wear with use. Keep the order document — it is the only thing you need to make a claim.

Why a Direct Contractor Answers Differently

We work with our own crews rather than passing the job to a middleman, so the master who measures is the same person carrying out the repair and the same one answering if something needs a second look. There is no handover between a call centre and a subcontractor who may have moved on by the time you ring back. With a middleman the guarantee is only as good as the subcontractor still being available, while a direct contractor has its own crews to send back, which is what makes a written promise worth having. When you compare offers around Kokshetau, ask which party will actually return — the company name on the paper or a stranger. A repair is only as solid as the people standing behind it.

Getting windows ready for the cold: the key points

Five points worth keeping in mind before you call anyone about your windows, drawn from the sections above and reduced to what actually decides the outcome.

  • Read the symptom first: a draught, condensation or a catching sash each points to a specific part, and the fix follows from that cause rather than from guesswork.
  • Repair usually wins while the frame and glass unit are sound: a warped frame or a fogged unit is where replacement starts to make sense instead.
  • Plastic, wooden and aluminium units all take repair: the material decides what the job involves, from seal type to hardware and fixings.
  • Check the result before the master leaves: the paper test around the sash shows whether the clamp is set right and the seal actually closes.
  • A written warranty naming both labour and parts is the clearest sign a contractor expects to be called back — and has no reason to fear it.

Questions about window repair in Kokshetau

Repair or replacement, seal, double glazing, winter repair

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can a plastic window be repaired or is it easier to install a new one?

In most cases the window is repaired: replacing the seal, adjusting the sash and repairing the hardware restore its functionality. Replacement is needed when the profile is damaged or the frame has lost its geometry, and this is visible during inspection.

02What signs show that the seal needs replacing instead of adjusting the window?

If the rubber has become hard, cracked or does not spring back when pressed, it is replaced. When the seal is elastic but there is a draft at the corners of the sash, adjusting the pressure and hinges is usually enough — the technician will determine this on site.

03Is it possible to replace only the double glazing unit without touching the frame?

Yes, the double glazing unit is replaced separately: the frame and sash remain in place if they are intact. This is also done when the unit has fogged up from the inside — the seal is already broken, and restoring it makes no sense.

04Is it realistic to repair a wooden window or is it better to install plastic?

A wooden window is repaired if the frame and sashes are sturdy: the seal is replaced, hardware is adjusted, and drafts are eliminated. Replacement with plastic is justified when the wood is rotting and the frame is warped, as shown by inspection.

05What is the difference between window repair and replacement when it freezes in winter?

Repair eliminates the cause: replaces the seal, adjusts the pressure, insulates the reveals, and the window stops freezing. Replacement is needed if the profile itself or the double glazing unit is damaged and restoration will not help.

06Can a window in Kokshetau be repaired in winter without waiting for warm weather?

Yes, most work is done right at home even in freezing weather, and the window is not removed. If a new double glazing unit is needed, it is replaced carefully without cooling down the apartment.

Reviews of window repair in Kokshetau

5,0based on 97 reviews on platforms
All reviews