EPDM seal
A basic option for most windows: the sash fits tightly again and keeps warmth through a long winter. From 1 000 ₸ per linear m.


EPDM seal
A basic option for most windows: the sash fits tightly again and keeps warmth through a long winter. From 1 000 ₸ per linear m.

German seal
Doesn't stiffen in the cold or swell from the humid air off the lakes, so the sash freezes less. From 1 200 ₸ per linear m.

Door seal
Heat escapes fastest through an old balcony door seal. We replace the whole contour from 5 000 ₸ per item.

Brush contour
A worn brush on a sliding frame lets in draughts and snow. A new one — from 1 150 ₸ per linear m.

Inter-frame seal
A third contour protects the window from cold from below and makes the room quieter. From 2 800 ₸ per window.

5,097 reviews on review sites
Even a good window loses heat if its seal is worn out. A new contour solves this without replacing the frame or glass.
A seal is a thin rubber tube in the grooves of the sash and frame. When compressed, it blocks the path of air and moisture. Old rubber shrinks, cracks, peels at the corners, and the window starts to freeze, fog up and let in cold.
The long winter and humid air from the lakes around Kokshetau test the seal's durability. A technician will match a seal to your window brand, remove the old one and install a new one, then adjust the sash pressure.

per linear metre of seal and technician's work
warranty on repair and replaced parts
payment when you have checked the window
Most often people contact us with these four problems.

In the morning the window won't open — there's ice along the contour because warm air escapes through a loose seal.
Drops on the frame and windowsill in winter are a common companion of an old seal and weak pressure.
If it's draughty right by the glass, the double glazing seal is worn, not just the sash seal.
The balcony door is opened most often, and its seal gives out first.
For a children's room and bedroom we recommend German seal, for a balcony door — a wear-resistant contour, for office sliding windows — a brush.
apartment windows

Flexible rubber for most PVC profiles, holds its shape in both frost and heat.
children's room, bedroom

Stays soft longer and reacts less to humidity and severe cold.
balcony and loggia

Dense rubber for a sash that is constantly opened and closed.
office sliding windows

New dense pile on the aluminium frame keeps out draughts and snow.
windows facing the wind

An extra layer between the frame and the sash removes cold at the bottom of the window.
The price depends on the length of the contours and the type of seal; the technician will give you a quote before starting work.
| Type of work | Price |
|---|---|
| EPDM seal for sashstandard option | from 1 000₸ per linear m |
| German sealwithstands frost and moisture | from 1 200₸ per linear m |
| Whole windowall contours at once | from 3 500₸ per window |
| Balcony doorseal around the perimeter | from 5 000₸ per item |
| Brush for aluminium sashessliding windows | from 1 150₸ per linear m |
| Seal maintenancecleaning and lubrication | from 750₸ per linear m |
| Inter-frame sealadditional contour | from 2 800₸ per window |
| Eliminate draughtsgaps along the contour | from 3 500₸ per sash |
| Winter adjustmenttight fit | from 3 000₸ per sash |
| Liquid plastic for seamsframe joints | from 1 500₸ per linear m |
| Wooden windows, insulationSwedish technology | from 4 200₸ per linear m |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Leave a requestWhat we guarantee to every customer.
on work and parts we replaced
KBE, Rehau, VEKA, Provedal and other window brands
fixed after inspection, no extra charges along the way
checking: cash, card or Kaspi
on WhatsApp to a photo of your window
we book you for a convenient day of the week
we take requests daily
we work across Kazakhstan
What happens after your request.

Describe the problem in WhatsApp: the window freezes, fogs up, or there is a draught from the door. A photo will help the technician prepare.

The technician checks all contours, hinges and the clamp, identifies the profile and gives you a price for the work.

We remove the old seal, clean the grooves, lay the new seal in one piece, and trim the corners neatly.

We set the sashes to winter clamping, check the window for draughts, and then you pay.
Good to know
We handle window seal replacement in Kokshetau with our own fitters, not through a middleman. A free measuring visit comes at a time that suits you, the fitter matches the seal to your window profile, and the work carries a 1-year warranty on labour and replaced parts. You pay after installation.
A draught along a closed window is usually blamed on the whole unit, but the seal is the first part to fail. Here is how to separate a tired gasket from a hinge fault.
If the sash sags or scrapes the frame, a new seal alone will not stop the draught because the moving part no longer sits square. Hinge hardware carries the weight of the leaf, and over years the lower corner drops by a few millimetres — enough to open a gap at the top edge that no fresh gasket can close. A worn hinge also lets the handle turn loosely and the panel drift when you push it. Check whether the gap between the leaf and the frame is even all round; an uneven gap means adjustment comes first. Tightening the hinge is cheaper and often removes the draught entirely, so order the two jobs correctly rather than replacing rubber that was never the cause.
The right seal is the one cut for your profile and your climate, not the cheapest roll on the shelf. This section covers what the fitter looks at and why.
We fit two seals on most units, a contour strip around the sash edge and a rebate gasket where the leaf meets the frame, and each wears at its own rate. The contour runs along the perimeter and guards the gap that opens when you turn the handle. The rebate sits deeper, in the recess between sash and frame, and closes the joint that the locking hardware pulls tight. On a standard PVC unit the outer contour is thinner and often flattens first at the corners, where the sash rubs most. That inner gasket takes the compression every time the sash closes, so it usually fails first and is the part to inspect on a draughty unit.
| Seal type | Where it works best |
|---|---|
| EPDM rubber | Cold winters, PVC and aluminium frames |
| Silicone | High heat, doors and sunny sides |
| TPE blend | Budget sashes, minor draughts |
| Brush strip | Sliding frames and loggia rails |
The visit runs in a fixed order so nothing is missed. Here is what happens from the initial message to the final check, and how long each part runs.
We re-seal balcony doors and loggia sashes as readily as room units, and a standard flat needs a single visit because the work goes sash by sash. Each one is handled at a time, so a room stays usable while the rest of the home waits its turn. Balcony doors get the same treatment, including the threshold line where draughts start. Window seal replacement in Kokshetau follows the same order, so the timing above holds for any unit. Doing it yourself looks simple until the channel has to be cleaned to bare plastic and the gasket pressed in evenly along the whole perimeter — a strip set at an angle leaks at the corners within weeks. A fresh seal settles over the coming days, so a unit that feels slightly tight now is normal and eases with use.
Not every draughty window needs a new one. This section sets out when a seal and an adjustment are enough and when the glass unit or the frame itself is the real problem.
If the frame and the glazing are sound and only the seal has gone, we replace it and adjust the hardware in the same visit, which costs far less than a full swap. Before blaming the seal, we check the sash for square, the panes for fogging between the layers, and the hinges for play. Hardware that drags or drops is corrected at the same time, because a fresh strip pressed against a misaligned sash wears out within months. Our repair warranty covers labour and replaced parts for a year. A unit that still closes flush and holds its shape is worth re-sealing; swapping it early throws away a structure with years left in it.
The terms are simple and set before any work starts. Here is what the warranty covers, how payment works and how to book.
Repair work carries a 1-year warranty that covers both the labour and the parts we replace, including the new seal. If a fitted seal starts letting draught through within that period, we come back and put it right at no charge. The same cover applies whether we changed the contour seal on a plastic sash, the rebate seal on a wooden frame or the seal on a loggia door. Larger jobs sit alongside it: installation carries a 5-year warranty and glass unit replacement a 3-year one, so a single order can cover several parts of the flat. Keep the order sheet from the measuring visit; it records the seal type fitted, which makes any later claim quick to check.
A seal lasts longer when it is looked after and the work is timed right. This section covers winter timing and simple care between visits.
We replace seals through the winter, and it is often the best time to do it because a failed seal shows up most clearly in the cold. When the rubber loses its elasticity, the rebate lets chill air through along the whole sash, and the draught is easy to feel by hand at minus fifteen. Kokshetau winters are long and sharp, so a stiff contour seal turns a warm flat into a cold one within a single season. Our fitters work indoors with the sash closed where possible, warming the profile before the new strip goes in. Book before the first hard frost if you can; a gasket that is already stiff lets in more chill once temperatures drop, and the fix is quicker to arrange ahead of the rush.
A worn seal is a small part with an outsized effect on warmth, quiet and draughts, and the decision usually comes down to a few clear checks rather than guesswork.
Signs of wear, scope of work, timelines, compatibility
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionIf the seal feels hard, has cracks, or does not spring back when pressed, it is time to replace it. When the seal is intact and soft but the sash does not press tightly, the issue is likely the hardware and adjustment is needed.
You can replace the seal on only one sash if the others are still elastic and maintain pressure. However, seals wear out at about the same rate, so on windows of the same age they are usually replaced all at once.
One sash takes about fifteen minutes; the exact time depends on the window and the condition of the profile. The technician will estimate the time for an apartment with several windows after inspection.
In most cases the sash is not removed: the old seal is pulled out of the groove and a new one is installed in place. The sash is only removed in complex cases when hardware interferes or the profile is deformed.
Yes, after installing a new seal the pressure becomes tighter, and the sash often needs adjustment. The technician checks the sash movement and adjusts the hardware so the window closes easily and without extra effort.
A universal seal may fit into the groove, but it will hold and press worse than a profile-specific one. For KBE, Rehau, and VEKA, a seal is selected for the specific profile so it fits precisely into the groove and lasts longer.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp