Technician holding a new seal for a wooden window in a living room
from 8 100 ₸ per windowOne-coat painting; master's visit and inspection — 3 600 ₸Calculate

Wooden Window Repair in Kokshetau

Sanding and painting · m²

Restoration

Sanding and painting the frame — from 18 000 ₸ per m². Restores wood protection and the window's appearance.

Wooden window after restoration with fresh varnish on the frames
GoogleYandex MapsZoon

5,097 reviews on review sites

What wooden window repair includes in Kokshetau

On-site restoration of the frame, sash and glass: from sanding and painting to glazing bead replacement and perimeter insulation.

How it works

A wooden window consists of a frame, sash, glazing bead, glass and hardware. Repair restores these elements to working condition: wood is protected from moisture, the sash is fitted to the opening, and glass and glazing bead are replaced if damaged.

Work is carried out at your home: the master takes measurements, identifies the cause — gaps, misalignment, rot or cracked glass — and chooses the restoration method. Warranty on window repair — 1 year for work and replaced components.

Honey-coloured wooden window with two sashes: frame, glass, hinges and a handle
from 16 000 ₸

wooden window frame repair per job

from 8 100 ₸

wooden window painting in one coat

1 year

warranty on window repair and components

6 types of work
PaintingInsulationGlassGlazing beadHardware

How wooden window restoration is done at home

The master works on site: from sanding the frame to replacing the glazing bead. Below are four stages that address common wooden window damage.

Technician applies varnish to a wooden window frame with a brush
  • 01Sanding and painting

    Old coating is removed, the wood is sanded and painted in one or several coats — from 8 100 ₸ per window.

  • 02Sash fitting

    The swollen sash is removed, edges are aligned and fitted to the opening so the window closes without effort.

  • 03Perimeter insulation

    Draughts along seams and rebates are eliminated: joints of the frame and sash are sealed so cold does not get inside.

  • 04Glazing bead replacement

    Fallen or rotten glazing bead is replaced with new so the glass stays in the frame and does not let draughts through.

Types of sash restoration work

Five works most often needed for a wooden window. Price is per unit — per window, per meter or per piece.

Painting

One coat · per window

A craftsman holds a can of white wood paint in his hand, fresh and smooth

Refreshing the protective coating of the frame and sash. Price — from 8 100 ₸ per window.

from 8 100 ₸

Insulation

Swedish technology · linear meter

Technician holds a roll of soft, flexible grey rubber seal

Sealing the frame perimeter. Price from 4 200 ₸ per linear metre.

from 4 200 ₸

Seal

Between frames · per window

Hands inserting a new seal into the groove of a wooden window sash

Protection against draughts around the sash perimeter. Price from 2 800 ₸ per window.

from 2 800 ₸

Hardware

Handles, hinges, latches

A craftsman holds a new metal window handle in his hand, shiny and sturdy

Replacement of worn parts. Price from 1 150 ₸ per item.

from 1 150 ₸

Glass

Glass and labour · m²

A craftsman holds a small clean pane of glass in his hand, whole and transparent

Replacement of broken glass with glazing bead fixing. Price from 8 000 ₸ per m².

from 8 000 ₸

Wooden window repair prices in Kokshetau

Prices for wooden window work; the exact cost is fixed by the technician in the order after measuring.

Type of workPrice
Wooden window restorationsanding and paintingfrom 18 000₸ per m²
Wooden window paintingone coatfrom 8 100₸ per window
Wooden window frame repairfixing misalignments and gapsfrom 16 000₸ per job
Wooden window repair and insulationSwedish insulation technologyfrom 28 000₸ per window
Wooden balcony block repairfull scope of workfrom 53 500₸ per unit
Wooden window hardware replacementhandles, hinges, latchesfrom 1 150₸ per unit
Wooden window insulation using Swedish technologysealing the perimeterfrom 4 200₸ per linear meter
Installation of inter-frame sealprotection from draughtsfrom 2 800₸ per window
Broken glass replacementglass and labourfrom 8 000₸ per m²
Master's visit and inspectionwithout ordering a repairfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card or Kaspi

Book a measuring visit

Why customers order wooden window restoration from us in Kokshetau

Facts about the company that matter when ordering wooden window repair.

Experiencesince 2012

we work across Kazakhstan

Repair warranty1 year

for work and replaced components

Scheduleno days off

we work every day

Coverage17 cities

you can order in 17 cities of Kazakhstan

Technician visit3 600 ₸

inspection without a repair order

Contact5 minutes

reply in WhatsApp within 5 minutes

Paymentafter installation

cash, card or Kaspi

Price fixationin the order

the price is fixed after measuring

How wooden window repair is carried out in Kokshetau

Four steps from request to acceptance of the work.

  1. Hand holding smartphone by wooden window, ceramic vase on windowsill nearby
    015 minutes

    Request

    You write in WhatsApp — we reply within 5 minutes and confirm the address.

  2. Tape measure stretched along wooden window sash during measurement before repair
    02free

    Measuring

    The technician arrives, inspects the window and takes measurements. Measuring and consultation are free.

  3. A workbench with tools, sandpaper, paint and sealant for window repair
    03on site

    Scope approval

    The technician specifies which work this particular window needs and records it in the order.

  4. Repaired wooden window with fresh white paint: one pane per sash, brass hinges
    04after work

    Acceptance

    You check the result and pay by cash, card or Kaspi. The price is fixed in the order.

Good to know

Wooden Window Repair in Kokshetau from Our Own Crew

Wooden window repair in Kokshetau by us means our own crew, not a middleman. We diagnose the frame and sash, restore the geometry, replace the seal, glass or glass unit, and repaint the wood. Measuring and consultation are free, and every repair carries a 1-year warranty on labour and replaced parts.

Restore the Old Frame or Fit a New Window

An old window often looks worse than it really is. The decision rests on the condition of the timber itself, not on how many decades the unit has stood in the wall.

How to Tell Whether the Wood Itself Is Still Sound

We check the frame for rot, deep cracks and soft spots before recommending anything, because sound timber can almost always be saved. The first pass is a probe with an awl at the sill, the lower corners of the sash and the joints where water collects — healthy fibre resists the point and shows pale and dry underneath. Dark, crumbly material that gives way under light pressure has already lost its structure, and no amount of filler will bring it back. Shallow cracks and flaking paint are cosmetic and get patched with filler before finishing. A sash that sticks or lets in a draught is usually a hardware or seal problem, not a sign the material is finished, so a full replacement is often unnecessary. When the timber is sound, wooden window repair in Kokshetau costs far less than a new unit and keeps the original frame in place.

What Restoration Gives You That a New Window Does Not

Restoration keeps the original frame, the window opening and the look of the facade, and a well-restored unit serves for years with normal care. We strip the old finish, treat the bare timber, replace damaged glazing beads and renew the paint layer so the surface is protected again from rain and frost. In older Kokshetau houses the frame is often built into the wall, so replacing it means reworking the opening and the finish around it, which restoration avoids entirely. Swapping the whole unit also resets the question of fitting and sealing against the wall, while restoring reuses an opening that has already settled. On a historic facade, the original proportions and profile are part of the building, and a new unit rarely matches them.

What a Wooden Window Repair Covers Step by Step

A window repair is a sequence of stages that touches the frame, the sash, the seal, the glass and the hardware, and the order matters as much as the work itself.

The Work We Do on the Frame, Sash and Glass

Repair stages and the materials each one uses
StageWhat we doMaterial or part
FrameFill cracks, sand, primeWood filler, primer
SashRestore geometry, tighten jointsHardware, wedges
SealRemove old seal, cut new grooveEPDM, TPE or silicone
GlassRe-glaze or swap the unitGlass, glass unit, glazing bead
FinishPaint or varnish the woodPaint, lacquer

Why a Sash Sags, Sticks or Squeaks and How We Fix It

A sagging or squeaking sash is almost always a hinge and alignment problem, and we reset the geometry and adjust the hardware rather than replace the window. On older frames the hinges wear unevenly, the screws loosen in the wood, and the leaf drops a few millimetres until its lower edge starts to catch. We rehang it, plane the binding edge where the wood has swollen, and set the locking points so the handle turns without force. A window that drags on the sill wears the seal flat within a season, so fixing the alignment early saves the seal as well.

Caring for the Wood After the Repair

  • Paint: refresh the coat every few years before cracks reach the bare wood.
  • Seal: wipe it clean and check for flattening once a year.
  • Hardware: lubricate hinges and locking points to stop squeaks.
  • Ventilation: air the room briefly each day to keep moisture down.
  • Small cracks: fill them early so water cannot sit in the frame.

Draughts, Insulation and Getting the Window Ready for Winter

Kokshetau's sharply continental climate brings hard frosts and sudden temperature swings that quickly expose every weak point in a timber window. Here is where the cold actually gets in and how we close it off.

Where the Draught Actually Comes From

Most draughts come from a flattened rubber strip, a loose casement or gaps at the glazing bead, and each of these is fixed without touching the timber. A compressed gasket stops springing back after several seasons and lets air slip along the whole casement line, while a leaf that has dropped on its hinges leaves a wedge-shaped gap at the top corner. We replace the sealing strip in windows from any manufacturer, including KBE, Rehau, VEKA and Provedal profiles, and rehang a sagging leaf rather than planing the wood. Sealing a draught from the room side only hides it, because cold air still enters at the outer edge and condenses inside the joint.

Winterproofing a Wooden Window in Kokshetau

We insulate the sealing line, the glazing bead and the joints, and most of this work can be done in cold weather because it does not depend on paint drying. A fresh gasket runs around the casement perimeter, the bead is re-seated with a new bed of compound, and the gaps between timber and wall are packed where the old filling has crumbled away. Hardware gets adjusted at the same time so the leaf pulls tight against the strip instead of resting loose. Paint and filler need above-zero conditions, so a full repaint is best planned for the warm season while gasket and hardware work can go ahead in winter. If the wood itself is sound, this is often the whole job.

A Glass Unit in an Old Wooden Frame

Replacing only the glass or fitting a unit into an old frame is one of the most common questions we hear. Below is what is actually possible and how the options differ.

Swapping the Glass Without Touching the Frame

We can replace a cracked or misted pane in the existing frame by removing the glazing bead, setting new glass and refitting the bead. The sash stays in place, the wood is left untouched and the work is usually done in a single visit. A thin pane of the same thickness drops straight back into the rebate; if the old pane was thicker or thinner, we match the new one to the rebate depth rather than forcing it. On older windows the bead itself is often the weak point, split or softened by years of sun and paint. If the old putty or bead is brittle, replacing the bead at the same time is what keeps the new pane sealed for years rather than months.

Fitting a Glass Unit Into a Wooden Sash

A slim unit can go into a timber sash if the rebate is deep enough, and we check that depth at the measuring visit before promising it. A unit of two panes with a sealed cavity needs more room than a single sheet, so the rebate has to be routed out or the sash rebuilt around it. On the plus side, the unit cuts heat loss and condensation on the inner pane noticeably. A heavier unit loads the hinges more, so the hardware is checked and adjusted at the same time to keep the sash from sagging. We give a 3-year warranty on glass unit replacement, and urgent units are made within one day at a surcharge.

The Measuring Visit, Timing and the Warranty

Before you book anything, it helps to know what happens on the measuring call, how long the job takes and what the warranty actually covers.

What the Measurer Checks and How Long the Work Takes

The measurer comes free at a convenient time, checks the frame, sash, seal and glass, and the repair itself is usually done in a single trip. We look at how the movable panel sits in the rebate, whether the timber has soft spots near the sill, how the gasket has flattened and whether the pane sits square. On older frames the fault is often one hinge or a dried-out strip rather than the whole unit, and that changes the plan. Small tasks are finished the same day; a panel that needs rehanging or a gasket swap takes longer. The measuring call is also where the price is fixed in the order, so nothing on the invoice changes once the crew starts. Ask the measurer to show you the worn part before it comes off — it tells you more than any estimate.

What the Warranty Covers and How to Choose a Crew

  • Warranty: 1 year on labour and replaced parts of the repair.
  • Payment: taken after completion, by cash, card or Kaspi.
  • Response: a WhatsApp reply within 5 minutes.
  • Schedule: open seven days a week.
  • Crew: our own masters, with no middleman between you and the job.

What to look at when restoring wooden windows

The decision on any old window comes down to a few clear checks: the state of the wood, the order of the work, and the terms you get in writing before anyone starts.

  • Sound timber is worth saving: rot and soft spots decide the question, not the age of the window.
  • Repair is a sequence: frame, sash, seal, glass and finish each need their own step, and skipping one shows up within a season.
  • Draughts have a source: a flattened seal or a loose sash is fixed without touching the frame.
  • Glass can be swapped: a pane or a slim unit fits the old sash when the rebate depth allows it.
  • Check the terms: a written warranty and a price fixed after measuring are the real test of a crew.

Questions about wooden window repair in Kokshetau

Restoration, double glazing, fittings, on-site repair

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can wooden windows in an apartment be restored without taking the frames outside?

Yes, restoration is usually done right in the apartment without removing the frames. The technician sands and paints the sashes on site, and only removes the window if there is serious damage — this is decided after inspection.

02What should be done if a wooden window sash has dried out and won't close?

First, the technician inspects the sash: if the wood is dried out, it is sanded, reinforced and refitted to the opening. Sometimes it's enough to replace the glazing bead and adjust the hinges, but the exact scope of work is determined on site.

03Can the double glazing in an old wooden window be replaced?

Yes, a modern double glazing unit can be installed in a wooden frame instead of ordinary glass. The frame and sash must be intact — the technician checks this during the free measuring visit, otherwise the replacement may not make sense.

04How can the fittings on a wooden European-style window be adjusted if the sash sticks?

Usually the hinges and locking mechanisms are adjusted: the fixings are tightened, the moving parts are lubricated and the sash is aligned. If the fittings are worn out, they are replaced with new ones — the technician does this after inspection.

05What is the difference between repairing a wooden window and a plastic one?

Wood requires more manual work: sanding, filling and painting, as well as taking the condition of the wood into account. Plastic more often only needs replacement of components and adjustment, so wood repair is usually more complex.

06Does a wooden window need to be removed for repair, or is everything done on site?

In most cases, repair is done on site without removing the window. Removal may only be needed for serious damage to the frame or sash — the technician determines this after inspection.

Reviews of wooden window repair in Kokshetau

5,0based on 97 reviews on platforms
All reviews