Craftsman adjusting a plastic window handle with a screwdriver in the living room
from 3,000 ₸ per sashSash adjustment takes minutes; technician visit and inspection are priced per the list belowCalculate

Window Repair in Temirtau

Sash pressure and position

Sash adjustment

Simple adjustment of sash pressure and position — from 3,000 ₸ per sash; complex adjustment with sash removal — from 4,000 ₸

A craftsman holds an L-shaped steel hex key for adjusting hinges
GoogleYandex MapsZoon

5,097 reviews on review sites

What window servicing in Temirtau includes

We check hardware, seals, glass units, sills and drip caps — fixing the cause, not the symptom.

How the service works

Window repair covers work on sash and frame components: adjusting sash pressure and position, replacing handles, hinges, seals, glass units, as well as replacing sills and drip caps, and sealing joints. The technician identifies the faulty component and restores it.

Warranty on window repair — 1 year for work and replaced components. We give 3 years for glass unit replacement and 5 years for window installation.

Technician in a dark blue T-shirt with a hex key at an open white PVC window sash
1 year

warranty on window repair and replaced parts

3 years

warranty on glass unit replacement

5 years

warranty on window installation

Works
AdjustmentHandle replacementHinge replacementSealGlass unit

How sash restoration is performed in Temirtau

Four common sash faults and what the technician does about them.

Close-up of an L-shaped hex key in the trunnion on the edge of an open white PVC window sash
  • 01Glass unit fogs up inside

    The sealant is broken, moisture between the panes; the technician confirms the diagnosis and suggests glass unit replacement.

  • 02Window won't close

    The sash does not engage with the strike plates because the hardware is misaligned. Adjusting the hardware restores the sash movement and handle operation.

  • 03Sagging sash

    The sash catches on the frame because the hinges have sagged. Adjusting the hinges lifts the sash and evens out the gaps around the perimeter.

  • 04Broken handle

    The handle won't turn or spins freely. The technician replaces the handle, removing the old one; hardware repair from 7,800 ₸.

Types of windows and structures we service

PVC windows from any manufacturer, wooden and aluminium, balcony doors and loggias.

PVC windows

KBE, Rehau, VEKA, Provedal

Technician holds a roll of grey rubber seal, showing it for replacement

Sash adjustment, replacement of handles, hinges and seals on windows from any manufacturer.

from 1 000 ₸ per linear metre

Wooden windows

Adjustment and repair

A craftsman holds an L-shaped steel hex key for adjusting hinges

We restore the seal pressure and sash movement on wooden windows, replace the seal.

from 1 000 ₸ per linear metre

Aluminium windows

Loggias and balconies

A craftsman holds a new white plastic window handle for replacement

Hardware repair and seal replacement on aluminium loggia structures.

from 1 000 ₸ per linear metre

Balcony doors

Adjustment and hinges

A craftsman holds a small square double-glazed unit sample for replacement

We eliminate door rubbing against the threshold, adjust and replace hinges on balcony doors.

from 3 000 ₸ per sash

Reveals and condensation

Reveal insulation

A craftsman holds a roll of gray mosquito netting for repair

For condensation and mould on the reveal, we adjust the seal pressure, replace the seal and insulate the reveal.

from 1 000 ₸ per linear metre

Window repair prices in Temirtau

Price list for window repair with units and timelines.

Type of workPrice
Technician visit and inspectionwithout ordering repairfrom 3 600₸ per job
Simple sash adjustmentsash pressure and positionfrom 3 000₸ per sash
Complex adjustment with sash removalwith removal and rehangingfrom 4 000₸ per sash
Window handle replacementwith old handle removalfrom 2 750₸ per pc
Hinge replacementupper or lower hingefrom 4 750₸ per pc
Hardware repairmechanism restorationfrom 7 800₸ per job
Sash hardware replacementset for one sashfrom 10 000₸ per sash
Seal replacementalong sash and frame contourfrom 1 000₸ per linear m
Glass unit replacementto fit the openingfrom 19 500₸ per m²
Broken glass replacementwith removal of remnantsfrom 8 000₸ per m²
PVC sill installationreplacing a cracked onefrom 5 500₸ per linear m
Drip cap installationwith joint sealingfrom 3 250₸ per linear m
Mosquito net repairmesh and fastenersfrom 2 500₸ per pc
Air inlet valve installationfor air supplyfrom 6 000₸ per pc

The price is fixed in the order after measuring.Measuring and consultation are free.Payment after installation: cash, card or Kaspi.

Calculate repair

Why customers order window fixing from us in Temirtau

Experience, warranties and production — facts you can verify.

Repair warranty1 year

Ask which specific work is covered by the warranty and for how long — in writing in the order

Double glazing warranty3 years

for double glazing replacement

Installation warranty5 years

for window installation

Experiencesince 2012

we work across Kazakhstan

Measuring0 ₸

measuring and consultation are free

Scheduleno days off

we work without days off

WhatsApp response5 minutes

we reply within 5 minutes

Coverage17 cities

you can order in 17 cities of Kazakhstan

How window restoration at your home in Temirtau is carried out

Four steps from request to checking the work.

  1. A hand holds a smartphone with a dark screen near a white PVC window
    01by appointment

    Request and consultation

    Describe the problem in WhatsApp — we will reply within 5 minutes and agree on a convenient visit time.

  2. A tape measure measures the lower edge of the window opening of a white PVC window
    02on site

    Measuring and diagnostics

    The technician inspects the sash, hardware and seal, and identifies the cause of the fault.

  3. A removed white window sash on a workbench next to a coil of new black seal
    03on site

    Work

    Adjusts the seal pressure, replaces the handle, hinges, seal or double glazing — depending on the diagnosis.

  4. A finished white PVC window with a new seal and handle, the sash closed evenly
    04after work

    Check and acceptance

    We check the sash movement, seal pressure around the perimeter and handle operation, and show you the result.

Good to know

Window Repair in Temirtau and Our Own Crews

For window repair in Temirtau, our team sends its own crews rather than subcontractors. We adjust sashes, replace seals in windows of any profile, swap fogged or cracked glass units and insulate frames, with a 1-year warranty on repair labour and replaced parts. Measuring and consultation are free, and we reply on WhatsApp within 5 minutes.

How to Tell What Your Window Needs Before You Call for Window Repair

A window rarely fails all at once. It signals first: a draught along the sash, condensation trapped between the panes, a sash that drags. Knowing which symptom is yours saves time, since each points to a different part.

Draughts, Condensation and a Sagging Sash and What Each One Points To

A draught usually means a worn seal or misaligned hardware, condensation inside the glass means the unit has lost its seal, and a sash that catches on the frame points to sagging hinges. The gasket flattens along the closing line where the leaf presses hardest, so the gap appears first at the handle side and the corners. Hardware misalignment shows up as a handle that needs a push to latch, or a leaf sitting unevenly in the opening. Fogging between the panes differs from surface mist: the moisture sits inside the sealed cavity, where wiping never reaches it. A leaf that scrapes the sill has dropped on its hinges, and the lower corner is where the wear starts. Read the symptoms together: a draught plus a fogged unit on the same opening usually means the glass is the root cause, not the rubber.

Repair or Replace and Where the Line Actually Sits

We repair the unit whenever the frame and profile are sound and the fault sits in the seal, hardware or glass unit, and we only recommend replacement when the frame itself is warped, cracked or rotten through. A sash that still closes square and holds its geometry is doing its job, whatever its age. On those, the work is a new glass unit, a fresh gasket run, or an adjustment of the hinges and locking points. Replacement enters the picture when the profile loses its shape, when a corner pulls apart, or when moisture reaches the timber or plastic and the material goes soft under the paint. A frame that is still square almost never needs replacing. The money usually goes into new glazing and a gasket, which is a fraction of the job.

A Quick Check You Can Do Yourself in Two Minutes

Run a sheet of paper around the closed sash. If it pulls out easily at any point, the seal or the adjustment is off there. Start at the handle side, work along the top edge, then down the hinge side and across the sill, keeping the same pull the whole way round. A sheet that slides out with no resistance marks a gap; one that tears or jams marks a spot where the leaf presses too hard, which is just as much a sign of misalignment. Note where it happens before you call, because that detail tells a technician which corner to look at first. Do this check on a cold morning, since seals and frames behave differently at low temperature, and a gap that seems fine in summer shows up clearly in the cold.

The Window Repair Jobs We Take On and What Each One Fixes

The set of jobs depends on what has actually failed. Below is what we do at the window and which component each job restores, so you know what you are paying for.

Adjustment, Seals and Hardware and What Each Job Restores

We adjust sashes, replace gaskets in units of any manufacturer including KBE, Rehau, VEKA and Provedal, and repair or swap hinges, handles and locking points when they no longer hold the sash tight. A leaf that drags on its surround usually sits off the hinges rather than being broken, so a correct adjustment brings it back square and the weatherstrip starts pressing evenly again. Those strips harden and flatten over time, which is why a draught often appears at the hinge side first. Worn hardware rarely needs a full swap — cleaning and re-greasing the locking points first tells you whether the mechanism is dry or actually broken, and that saves the cost of parts. This is the kind of window repair Temirtau residents most often need, and it is usually the quickest to put right.

Glass Units, Fogged Panes and a Same-Day Swap

A fogged or cracked glass unit is replaced on its own without touching the frame, and we can make and fit an urgent one within one day for a surcharge on that part. The outer structure, sashes and hardware stay in place, so the room is not opened up to the weather and the work is far smaller than a full glazing change. Mist trapped between the panes means the desiccant inside has given up, so wiping the surface will never clear it — the sealed panel has to come out, and the surround stays exactly where it is. If the mist sits on the room side instead, the glazing is fine and the problem is ventilation or the gasket.

Wooden, Aluminium and Plastic Units and How the Job Differs

How the window material changes the repair scope
Window typeWhat we restoreWhat to expect
PlasticSeals, hardware, glazed panelsStraightforward swap of worn parts
WoodenSeals, hinges, glazed panelsTimber often stays sound
AluminiumSeals, locking points, glazed panelsSlim profiles need matched parts

Why Windows in Temirtau Wear Faster and How Window Repair Slows It Down

Windows here live in harder conditions than most of the country: industrial dust, sharp temperature swings and condensation wear seals and hardware down faster, and that shapes which jobs a flat actually needs and how often.

Dust, Temperature Swings and What They Do to Seals and Hardware

Industrial dust settles into the seal groove and the hardware, and repeated freeze-thaw cycles harden the rubber, so seals in Temirtau tend to lose their spring sooner than in cleaner, milder places. The grit works like a slow abrasive on hinge pins and tilt mechanisms, while condensation that forms on cold mornings runs into the same grooves and carries dust deeper. A sash that closes with a heavier push than last season is usually showing this wear rather than a fault in the profile itself. A seal that looks intact can already be stiff and flat on the contact edge — pressing it with a finger shows whether it springs back or stays compressed, and that is the real test, not the surface look.

Getting the Window Ready Before the Cold Sets In

We adjust the sash, check and replace the seal where it has gone flat, and insulate the frame before the cold, so the unit holds heat through the winter instead of leaking it. Adjustment brings the sash back to even pressure across the whole perimeter, which matters more than any single seal, because one loose corner lets cold air through the rest of the frame. We change the seal on units from KBE, Rehau, VEKA and Provedal profiles, so the rubber matches the groove rather than being trimmed to fit. Book the check in early autumn rather than at the first hard frost — once the cold arrives, seals are stiff and adjustment is harder to judge.

Keeping Dust Out with the Right Screen Cloth

For dusty air we fit the Anti-Dust and Anti-Pollen (Poll-Tex) cloths, and the Poll-Tex anti-pollen mesh has a fine 0.25×1 mm cell that holds back fine dust and pollen that a standard mesh lets through. The difference shows on a street-facing unit: a coarser fibreglass cloth stops insects but passes the grey film that settles on sills by midsummer. A finer cell also cuts airflow, so on a sash you keep open for ventilation all summer the standard or Ultravue cloth often feels better — Ultravue passes 25% more light and air than other meshes — while the fine cloth suits bedrooms and rooms facing the road. Frame colour and fixings we match to your unit at the free measuring visit.

How a Window Repair Visit Runs from First Message to Final Check

The work runs from your first message to a check of the result on site. Below is how the appointment is arranged, what the free measuring covers and how long an adjustment takes, so you know the timing in advance.

From Your First Message to a Scheduled Visit

You message us on WhatsApp and we reply within 5 minutes, we agree a convenient time for the measurer, and we are open seven days a week so the appointment can land on a day that suits you. The measurer arrives at the hour you pick, takes the sizes and helps choose the design, mesh and fixings. The price is fixed in the order after measuring, so nothing shifts once the work is agreed. For repair work in Temirtau, we agree the visit for the earliest convenient day. Send a photo of the unit with your first message — it helps us bring the right parts straight away instead of coming back for them.

What the Free Measuring Visit Covers

Measuring and consultation are free, the measurer comes at a time that suits you, takes the sizes and helps choose the design, mesh and fixings, and the price is fixed in the order after measuring. The appointment covers the full unit, not just the part you noticed: the sash, the seal line and the hardware are all checked while the specialist is there. That person also picks the fastening for your profile and floor — Z-brackets, pins or magnets — because the right fixing depends on the frame and the height, not on the screen alone. Ask for the fixing to be written into the order, so the crew arrives with the correct brackets rather than improvising on site.

How Long the Work Takes and When It Is Done in One Visit

Job types against working time and number of trips
JobHow long it takesOne visit or more
Adjustment of a sashUnder an hourOne
Seal replacementUnder an hourOne
Framed screen, made to size10–15 minutesOne
Pleated screen, made to size40–60 minutesOne
Urgent glass unitWithin one dayOne

Mosquito Screens Made to Size and Window Repair Done on the Spot

A screen is not one product but a line of cloths and frame types, each built for a different job. Below we set out which cloths we fit and when a screen is worth repairing rather than replacing.

Five Cloths and What Each One Is For

cloth types side by side by function
ClothWhat it doesBest for
Standard (Fiberglass)Standard weave, resists heat and temperature swingsEveryday windows and doors
Ultravue (Ultravue)25% more light and air than other meshesRooms you ventilate often
Anti-Cat (Pet Screen)Vinyl threads hold a small animal's weightHomes with cats
Anti-DustDenser weave traps fine dustStreet-facing windows
Anti-Pollen (Poll-Tex)0.25×1 mm cell blocks pollenAllergy season
Metal / KryloRigid metal and reinforced clothDoors and high-wear spots

Repair or a New Screen and How to Decide

We repair screens and replace the fastenings when the frame and cloth are still sound, and we make a new screen when the cloth is torn across or the frame is bent, with a framed screen made to size in 10–15 minutes. A pleated screen takes 40–60 minutes because the folding stack has to be set to the opening. Our 1-year warranty covers both the labour and the parts we swap, whether that is a fresh cloth, new clips or a re-strung frame. A small tear near the edge is often a fastening problem rather than a cloth problem — if the screen keeps popping out of its clips, the fix is the fastening, not a new cloth.

Frame Colour, Door Profiles and Fixings for Your Window

We paint the screen frame any colour to match your windows, fit screens on plastic, wooden and aluminium windows, and door screens come with Economy 32×10 mm or Prestige 42×17 mm profiles. The measurer picks the fastening for your window profile and floor — Z-brackets, plunger pins or magnets — so the frame sits flush instead of rattling in the wind. A framed screen lifts out from inside in a minute, so it is worth taking it off for the winter — stored flat and dry, the cloth and frame last far longer than one left out through the cold. Ultravue suits a room you air daily; Pet Screen trades some airflow for strength where a cat leans on the mesh.

Window Safety, Winter Prep and Who Stands Behind the Work

Beyond the repair itself, two things matter most: that the unit is safe around children, and that whoever does the work is the one who answers for it. Below is how we handle protection and who stands behind each task.

Locks, Restrictors and Grilles as One System

We fit locks, restrictors and grilles as one system, so a child cannot open the sash wide while the unit still opens for ventilation and cleaning. A restrictor is a small limiter screwed to the frame that lets the sash swing only to a set point, enough for air but not enough to climb through. The handle lock is the second half: it stops a child from releasing the restrictor and pushing the pane past that point. On ground-floor and upper-floor units alike, the pair works together, and a grille adds a fixed barrier where the opening faces a drop. Our fitter sets the restrictor position to the profile and the room, not to a single default. A restrictor alone stops the sash opening past a set point, but a lock on the handle is what stops a child from releasing it.

Why a Direct Contractor Changes the Warranty

We are a direct contractor with our own crews, not an aggregator, so the people who do the work are the people who answer for it, and we give a 1-year warranty on repair covering labour and replaced parts. That distinction matters more than it sounds. When a task is passed to a middleman, the crew that arrives may never have seen your unit before, and the guarantee travels through two hands. If a sash starts catching again, it is unclear who returns to fix it. With our own fitters, the same team that adjusted the sash and changed the seal comes back to look at it. That is the difference between a promise on paper and a crew that remembers the work, which is what the guarantee is actually worth.

Payment, Timing and the Warranties on Each Job

Coverage terms and payment timing by service type
JobWarrantyPayment
Window repair1 year, labour and partsAfter installation
Glass unit replacement3 yearsAfter installation
Window installation5 yearsAfter installation
Mosquito screen1 yearAfter installation

What to consider before window repair

A window problem is easier to solve once you know which part is failing. These closing points pull the whole picture together before you book a visit.

  • Symptom points to the part: a draught usually means seals or hardware, fogged glass means the unit itself, and a sticking sash means adjustment or hinges.
  • Repair or replace follows the frame: if the profile is sound and only a component has failed, repair stays the sensible route; a warped frame changes the calculation.
  • Winter prep runs ahead of the cold: seals and hardware hold up better when checked and adjusted before the first hard frost, not after.
  • A screen is a range, not one item: match the cloth to the job — Ultravue for light, Pet Screen for animals, Poll-Tex against pollen.
  • Warranty and a direct contractor decide: confirm who performs the work and what covers labour and parts, since that is what you rely on later.

Questions about window repair in Temirtau

Double glazing, hardware, seals, wooden windows

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can the double glazing be replaced separately without changing the whole window?

Yes, the double glazing is replaced separately: the frame and sash stay in place, and the technician removes the glazing beads and installs a new unit. This is possible without a full window replacement if the profile and hardware are in good condition.

02How can you tell when a window can be adjusted and when the hardware needs replacing?

If the sash catches on the frame, doesn't close tightly, or the handle turns stiffly, adjusting the hinges and the closing pressure is usually enough. Replacement is needed when the mechanism is jammed, loose, or parts are worn out — the technician determines this on site.

03What should you do if the sash starts catching on the frame again after window repair?

First check whether the closing pressure has loosened or the sash has sagged again — under the window repair warranty, the technician will inspect the hinges and pressure. If the window has warped due to the opening's geometry, a more thorough rebuild may be required.

04Do you repair wooden windows in old buildings in Temirtau, or is it better to install plastic windows right away?

We take on wooden windows in Temirtau: we rebuild the sashes, replace the seal, and adjust the hardware. If the frame and sashes are intact, repair is possible without switching to plastic.

05Which seal is best for windows in a sharply continental climate?

EPDM is suitable for this climate: it is elastic and resistant to frost and heat. TPE loses its properties faster, and silicone is more suited for indoor work.

06Can a window in a panel building be repaired without removing the frame?

Yes, in most cases repair is done without removing the frame: the sashes are adjusted, and the seal and double glazing are replaced. Removal may only be needed for serious profile damage.

Reviews of window repair in Temirtau

5,0based on 97 reviews on platforms
All reviews