Swedish method
We cut a groove in the wooden frame and fit a rubber seal, so draughts disappear. From 4 200 ₸ per linear metre.


Swedish method
We cut a groove in the wooden frame and fit a rubber seal, so draughts disappear. From 4 200 ₸ per linear metre.

Sill
We seal the joint under the sill where wind and snow blow in. From 2 000 ₸ per linear metre.


Double-chamber unit
We replace single glass with double-chamber units — price after measuring the window.

Reveal
We insulate the reveal where moisture collects in winter. From 19 900 ₸ per linear metre.

5,097 reviews on review sites
In offices, child's rooms, kitchens and country houses: wherever it is cold by the window, draughty or mould grows.
Cold gets in through old wooden frames, the joint under the sill, loose balcony sashes and thin glass. The technician finds these spots, seals them and adjusts the sashes, and replaces the double glazing if needed.
Temirtau stands in the open steppe: winters bring strong winds and frost, and unprotected windows quickly lose heat. We work in flats, private houses, country houses and offices.

per linear metre of Swedish method
warranty on work and parts
warranty on double glazing replacement
Four common requests.

The wooden window has dried out and the sash no longer fits the frame.
There is a gap outside under the sill where wind and snow blow in.
The loggia sashes close with a gap, and cold air comes into the kitchen.
A single-chamber unit gets frosty at the edge in freezing weather.
We choose by window type and task.
wood

Groove and rubber seal along the whole sash.
outside

Sealant under the sill against wind and snow.
inside

Insulation of loggia walls and floor.
windy side

Third rubber seal.
diagnostics

Image of cold spots on the window.
The total depends on the window and the work; the technician will give it during the visit.
| Type of work | Price |
|---|---|
| Full windowall required work | from 3 800₸ per window |
| Sash sealnew seal | from 1 000₸ per linear metre |
| Draught-proofinggap sealing | from 3 500₸ per sash |
| Indoor jointliquid plastic | from 1 500₸ per linear metre |
| Facade joint and sillsealant | from 2 000₸ per linear metre |
| Insulated revealready for finishing | from 19 900₸ per linear metre |
| Window sillno voids | from 15 000₸ per job |
| Swedish methodwood | from 4 200₸ per linear metre |
| Extra pressureor micro-lift | from 1 700₸ per item |
| Between framesthird seal | from 2 800₸ per window |
| Thermal cameracold spot detection | from 9 000₸ per job |
| Balcony insidewalls, floor | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Call a technicianWhat you should know.
on repairs and parts
warranty on double glazing replacement
we work with any
after inspection, no extra charges
cash, card, Kaspi
on WhatsApp
09:00–19:00 every day
we have been working with windows
The technician's workflow.

Message us on WhatsApp where it's cold: frame, sill, balcony or glass, and send a photo.

The technician checks the window and quotes the cost of the necessary work.

We install rubber seals in wood, seal sills and joints, and adjust balcony sashes.

We check the window together with you and only then take payment.
Good to know
We handle window insulation in Temirtau as a direct contractor with our own team, not through middlemen. We start with a free measuring visit, find where the cold actually gets in, then replace weatherstripping, adjust sashes or fit a new glass unit as needed. You pay after the work is done.
A shut sash does not mean a sealed window. Before any work we trace where the cold enters, because the fix for a worn seal is not the fix for a cold glass unit.
We check the seal first, because a draught along the frame edge and condensation in the middle of the pane are two different symptoms. Run your hand around the perimeter on a frosty day: moving air at the rebate means the weatherstripping has lost its compression, and a careful adjustment of the hardware often restores the fit without new parts. Condensation that beads on the pane and freezes in frost is a different story, and it usually means the sealed unit has failed. On our calls across the city, we see both faults in the same flat more often than either alone. Proper window insulation in Temirtau starts with telling these two faults apart, so the repair targets the real source of the cold. Damp film on the pane points to a failed unit, while a draught at the frame edge is almost always the weatherstripping.
Most cold windows do not need a new window. The real choice is between adjusting what is there, resealing it, or replacing the glazing, and the right answer depends on what the diagnosis found.
| Option | What it fixes | When we recommend it |
|---|---|---|
| Adjustment | Leaf sitting loose, draught at the edge | Frame is sound, sash has dropped |
| Resealing | Worn weatherstripping along the frame | Seal is flattened, cracked or hard |
| Replacement | Failed glazing, condensation inside | Mist or frost forms between the panes |
We fit an energy-saving glass unit when the old one has failed and you want to cut heat loss through the glazing itself, not just stop a draught. The coating on the inner pane reflects warmth back into the room, and the argon fill slows the transfer that a standard pane allows. For insulation in Temirtau, that matters most in north-facing rooms and on upper floors, where wind load and exposure run higher than on a sheltered ground-floor wall. A new pane only pays off if the frame and seal are already sound, so we fix the perimeter first and treat the glazing as the second step. In our practice, swapping it before the weatherstripping is renewed leaves the same cold edge along the sash — start at the perimeter, then decide on the glass.
The weatherstripping is the cheapest part of the window and the one that fails first. Choosing the right material for a Temirtau winter matters more than the brand on the frame.
We replace the weatherstripping on sashes of any manufacturer, including KBE, Rehau, VEKA and Provedal profiles. The strip runs along the whole perimeter of the sash, and the corners and the hinge side compress first. In our practice, the groove width differs between profile systems, so the seal is matched to the groove in your profile — the profile has to be identified before the visit. A replacement takes well under an hour per sash, and the old strip comes out with a flat screwdriver without removing the sash. Ask the fitter to check the drainage slots too: a new seal over a blocked slot still lets water in. A seal that hardens in frost stops pressing against the sash, so the draught returns within a season even though the strip still looks intact.
The same draught has a different cause depending on what the frame is made of. Wood, plastic and aluminium each fail in their own way, and the insulation work follows that.
We insulate timber units without replacing them with plastic, working on the weatherstripping, the sash fit and the gaps around the casing. Old felt or worn rubber is pulled out and replaced with a profile that compresses evenly along the rebate. The moving parts are then adjusted so they close square, because timber that has dropped by a few millimetres leaves a slit along the hinge side that no gasket will close. Where the casing meets the wall, loose mortar and cracked putty are raked out and refilled. Adjustment on timber takes longer than on PVC, since there are no hidden cams to turn. Old wooden units move with the seasons, so a tight autumn fit can open a gap by deep winter, and the work has to allow for that movement.
On plastic and aluminium frames we work on the sash, the gasket and the slopes, since heat also escapes where the frame meets the wall. A PVC leaf is adjusted with an Allen key at the hinge cams: a quarter turn lifts a sagging corner back into contact. Aluminium behaves differently, because the metal conducts cold straight through, so the gasket and the slope connection carry most of the insulation. Slopes matter for noise as well: a foam-filled one with a sealed edge takes the edge off street traffic, while a hollow one passes sound through. In older blocks one room often runs colder than the rest, and the cause is usually a single open seam rather than the glass. A well-sealed leaf still feels cold if that seam is open, so the perimeter is checked on the same visit as the unit itself.
The process begins with a measurement, not with a sales pitch. The measurer finds the fault, proposes the work and fixes the price before anything is ordered.
The measurer arrives at a time that suits you, takes the sizes, examines the weatherstripping and the sash fit, and helps you choose the parts. Measuring and consultation cost nothing, and the same appointment covers the whole job: the specialist looks at the gaps along the frame, tests how the leaf sits in the rebate and notes the profile type before recommending a gasket or a repair. Parts are picked on the spot for the profile and the storey, since a top-level flat and a ground-level property load the frame differently. Because the price is fixed in the order after measuring, the figure you agree on during the appointment is the figure you pay, and nothing is added once the work starts.
We give a 12-month guarantee on repair work covering labour and replaced parts, three years on a glass unit swap and five years on installation. If a sealed pane has failed and the flat is losing heat fast, urgent manufacture and replacement can be done within a day at a surcharge on the pane itself. Payment is taken after installation by cash, card or Kaspi, so the guarantee and the payment both sit at the end of the job rather than the start. Ask for the terms in writing on the order — it is the document you rely on if a gasket starts leaking again in the first cold snap.
Heat loss in a Temirtau flat usually comes from a handful of predictable spots, and each one has a sensible fix that costs less than a full window swap.
Draughts, condensation, seal, freezing
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionMost often the cause is a worn seal, loose hardware pressure, or a gap along the frame perimeter. During the inspection, the technician finds the source and decides whether insulation is enough or adjustment is needed.
It will help if moisture and frost appear along the edge of the glass and on the frame due to draughts. If condensation collects inside the double glazing between the panes, insulation will not help and the double glazing unit needs replacing.
Check for drops and frost inside the double glazing between the panes: if present, insulation will not help. Clean glass with a cold frame and draughts means the window only needs insulation and adjustment.
Replacing the seal restores airtightness at the rebate but does not address seams, reveals, or hardware. Insulation is a set of works: they check the pressure, draughts along the contour, add extra pressure if needed, and insulate problem areas.
A wooden window is insulated if the frame and sashes are intact: the seal is replaced, the rebate is tightened, reveals and seams are insulated. If the frame geometry is compromised, insulation gives little — then replacement is discussed.
Freezing along the edge of the glass usually indicates a problem with the double glazing or spacer bar, not draughts. Insulation will eliminate draughts, but if the cold comes from the double glazing, its replacement is discussed.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp