Technician holding a new seal for a wooden window on a warm loggia
from 8 100 ₸ per windowPainting, insulation and glass replacement. Master visit and measuring are free.Calculate

Wooden Window Repair in Temirtau

Draughts · Swedish technology

Window insulation

Insulation using Swedish technology — from 4 200 ₸ per linear m. We eliminate draughts from gaps and frame freezing.

Technician holds a roll of soft, flexible grey rubber seal
GoogleYandex MapsZoon

5,097 reviews on review sites

What a wooden window consists of

We explain what elements a wooden window consists of and which areas wear out first.

How it works

A wooden window consists of a frame, sash, glazing bead, glass and hardware. The frame holds the geometry of the opening, the sash opens, the glazing bead secures the glass, and the hardware is responsible for closing and pressing.

The bottom of the sash, glazing bead and hardware wear out first: wood absorbs moisture, paint cracks, fixings loosen. Repair restores the window's airtightness and sash operation without replacing the whole unit.

Honey-coloured wooden window with two sashes: frame, glass, hinges and a handle
1 year

warranty on window repair and replaced components

0 ₸

measuring and consultation — free

09:00–19:00

accepting requests in Temirtau, working without days off

6 services
InsulationPaintingGlassGlazing beadHardware

How window restoration is performed in Temirtau

Four stages of the master's work on site — from frame inspection to sash check.

Technician applies varnish to a wooden window frame with a brush
  • 01Frame and sash diagnostics

    The master inspects the wood, hardware and seal, notes areas of draughts and damage.

  • 02Surface preparation

    Removes peeling paint, cleans and sands areas for painting or repair.

  • 03Insulation and adjustment

    Insulates using Swedish technology, adjusts the sash, replaces a section of wood if rotten.

  • 04Work with hardware and fixings

    Lubricates mechanisms, tightens hinges, replaces the handle or locking mechanism if worn.

Types of wooden window work in Temirtau

Five types of work with an approximate price per unit — the exact cost is confirmed by the master after measuring.

Insulation

Swedish technology

Technician holds a roll of soft, flexible grey rubber seal

We eliminate draughts from gaps and frame freezing while preserving the wooden structure.

from 4 200 ₸/linear m

Painting

Sanding and coating

A craftsman holds a can of white wood paint in his hand, fresh and smooth

We remove the old coating, sand and paint the window to protect the wood from moisture.

from 8 100 ₸/window

Glass replacement

Glass and labour

A craftsman holds a small clean pane of glass in his hand, whole and transparent

We replace broken or cracked glass and restore the fixing in the glazing bead.

from 8 000 ₸/m²

Glazing bead replacement

Glass fixing

Hands fixing a wooden glazing bead back in place with a hammer, wooden window repair

We replace fallen out or damaged glazing beads so the glass stays in the sash.

from 16 000 ₸/job

Hardware replacement

Handles, hinges, compression

A craftsman holds a new metal window handle in his hand, shiny and sturdy

We replace worn hardware parts and restore the closing and compression of the sash.

from 1 150 ₸/pc.

Wooden window repair prices in Temirtau

Indicative price list for wooden window work in Temirtau.

Type of workPrice
Wooden window restoration (sanding, painting)includes preparation and paintingfrom 18 000₸ per m²
Wooden window paintingone windowfrom 8 100₸ per window
Wooden window frame repairmaterials not includedfrom 16 000₸ per job
Wooden window repair and insulationinsulation and draught-proofingfrom 28 000₸ per window
Wooden balcony block repairbalcony blockfrom 53 500₸ per unit
Wooden window hardware replacementper hardware itemfrom 1 150₸ per unit
Wooden window insulation using Swedish technologylinear metrefrom 4 200₸ per linear m
Inter-frame seal installationone windowfrom 2 800₸ per window
Broken glass replacementglass and labourfrom 8 000₸ per m²
Master visit and inspectionwithout ordering a repairfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card or Kaspi

Ask about repair cost

Why customers order window restoration from us in Temirtau

Facts about the company that matter when choosing a wooden window specialist.

Experiencesince 2012

we work across Kazakhstan

Repair warranty1 year

for work and replaced components

Measuring0 ₸

measuring and consultation are free

Paymentafter

payment after installation: cash, card or Kaspi

Scheduleno days off

we accept requests daily

Pricefixed

in the order after measuring

Coverage17 cities

you can order in 17 cities of Kazakhstan

Contact5 minutes

we reply on WhatsApp

How wooden window restoration is carried out in Temirtau

Four steps from request to work inspection.

  1. Hand holding smartphone by wooden window, ceramic vase on windowsill nearby
    015 minutes

    Request

    You write on WhatsApp — we reply within 5 minutes, clarify the problem and a convenient time.

  2. Tape measure stretched along wooden window sash during measurement before repair
    02at a convenient time

    Measuring

    The master arrives, inspects the window and agrees with you on the visit time and access to the window.

  3. A workbench with tools, sandpaper, paint and sealant for window repair
    03depending on scope

    Work

    Performs insulation, painting, glass replacement or sash adjustment on site.

  4. Repaired wooden window with fresh white paint: one pane per sash, brass hinges
    04after work

    Inspection

    Checks the sash movement and compression, shows the result and accepts payment after installation.

Good to know

Wooden Window Repair in Temirtau from Our Own Crew

Wooden window repair in Temirtau is done on site by our own crew, not through an agency. We diagnose the frame, fix sagging sashes, swap worn seals and insulate for the winter, with a 1-year warranty on the work and replaced parts. Measuring and consultation are free.

Can wooden window repair save your old window or is replacement needed

Repair is possible more often than owners expect. The call depends on the condition of the timber and the geometry of the sash, not on how old the window looks from the street.

Signs a Wooden Window Still Has Years Left

  • Sound timber: a screwdriver pressed into the lower rail meets solid material, not a soft, crumbling core.
  • Square sash: the leaf closes without rubbing and the gaps around it stay even.
  • Surface cracks only: hairline splits along the grain are cosmetic and close up with filler.
  • Working hardware: a stiff handle or a dropped hinge is a fitting problem, not a reason to pull the frame.
  • Dry but tight joints: mortise corners that still hold can be re-glued and wedged.

When Replacement Makes More Sense Than Repair

Replacement is the honest answer when the frame is rotten through or the leaf has lost its shape beyond what planing can fix. Soft material at the bottom edge, joints that open again after re-gluing, and a sash that will not sit flat after a full rehang all point the same way: the timber has given up, not the fittings. Old double-frame housing is the usual case, where the inner and outer leaves warp in opposite directions and no adjustment brings them back to a parallel gap. Planing buys a season at best, because the wood springs back once it dries further. A repaired unit that keeps its original frame usually outlasts a cheap swap, so the decision should follow the material, not the calendar. If you are weighing up wooden window repair in Temirtau, the condition of the timber is what settles the question.

What wooden window repair does for a window in our climate

The Swedish method is not a replacement window — it is a fresh groove cut around the sash and a continuous seal pressed into it. Here is what that changes when the frost drops hard.

How the Seal Groove Is Cut and Why It Beats Stuffing

We cut a fresh groove around the sash with a router and press a continuous seal into it, so the gap closes evenly instead of being packed by hand. The cutter runs along the perimeter of the leaf at a fixed depth, which keeps the channel the same width on every side — corners included, where hand-stuffed foam usually leaves a hollow. A single rubber cord then sits inside that channel under light compression. On older timber, where the rebate has dried and warped, the router also levels the seating surface before the cord goes in. A routed groove holds the gasket against the frame through freeze-thaw cycles, which is why it outlasts foam or glued strips in a sharply continental climate.

Choosing a Seal and Adjusting the Old Hardware

Seal materials matched to how each sash closes
Seal typeBest forHow it behaves in frost
EPDM rubberStandard hinged sashesStays elastic to about minus 40
SiliconeSashes that bind or swellKeeps flexibility at lower temperatures
TPELoose, worn rebatesSofter compression, easier on old timber

What a Wooden Window Repair Covers Step by Step

The work happens at your home: the window stays in the wall, and nothing is taken away to a workshop. Below is what our crew actually does on site and how much time one window takes.

On-Site Work From Diagnosis to Painting

  • Diagnosis: we check the leaf for warp, probe the timber for soft rot and test how it closes.
  • Fitting: the leaf is re-hung and the hinges adjusted so it sits square in the opening.
  • Seal replacement: the old gasket comes out, the groove is cleaned and a new seal set.
  • Hardware service: handles, stays and hinges are lubricated, tightened or swapped on the spot.
  • Touch-up paint: bare spots and repaired edges are primed and painted to match the frame.

How Long One Window Takes and How Often to Service It

A single timber window is usually finished within one visit, and we advise a light service check once a year before the heating season. Most of that hour goes on the seal and the moving parts rather than on the paint, because a leaf that no longer pulls tight lets cold air through long before the frame itself shows damage. Our crew carries the common hinge and stay sizes on the van, so a worn part is replaced on the spot instead of being ordered and fitted on a second trip. On older frames the first visit often runs longer, since softened wood near the sill needs cutting back and priming before any new coat goes on. Repainting every few years and re-tensioning annually is cheaper than letting a small gap grow into a warped leaf.

Wooden window repair and sealing before the Temirtau winter

A draught is a symptom, not a verdict. We look at where cold actually enters a timber window and what genuinely helps before the frosts arrive.

Finding Where the Cold Actually Gets In

  • The seal line: a flattened gasket under the sash stops springing back, so air slips past the whole perimeter.
  • The gap between sashes: sagging hinges let the casements drift apart, opening a slit along the meeting edge.
  • The junction with the sill: cracked putty and dried foam at the bottom rail let cold crawl up.
  • The wood itself: hairline splits along the grain widen in dry indoor heat and pass air straight through.

Insulating Without Replacing the Window

We insulate by renewing the seal line, closing sash gaps and treating the timber, so the window holds warmth without a full replacement. The old gasket comes out of its groove, the wood underneath is cleaned and primed, and a fresh strip goes in along all four sides. Sagging hinges get tightened or swapped so the casements meet evenly, and dried-out sections are fed with oil rather than covered with filler. Draught-proofing a timber window this way also slows the drying and cracking that timber suffers when cold air keeps washing over it. Insulation done before the first hard frost lets the new seal settle into place, while a mid-winter job risks trapping moisture inside — book the work while the nights are still mild.

A mosquito screen that fits a wooden window repair frame

A timber frame takes its own kind of fixing, and the wrong bracket either splits the wood or works loose by August. Below are the fabrics and fastenings that suit such units, and how the net comes off for winter.

Meshes and Fixings That Suit Timber

Which mosquito fabric suits which wooden opening
FabricWhat it is forNote
FibreglassEveryday insect protectionResists fire and temperature swings
UltravueRooms where light matters25% more light and air than other meshes
Pet ScreenHomes with a catVinyl threads hold a small animal's weight
Poll-TexAllergy season0.25×1 mm cell blocks pollen
Metal meshHigh-traffic openingsStiffer surface, less give

Making the Screen and Taking It Off for Winter

A framed screen made to your size takes 10 to 15 minutes, and a pleated one 40 to 60 minutes, with the frame painted any colour to match your windows. We fit these units to timber windows with Z-brackets, pins or magnets chosen for the profile and the floor the opening sits on. Soft wood needs a wider bearing point, so the fixing is picked on site rather than from a catalogue — a measurer confirms it during the free visit. A framed panel lifts out from inside in a minute, so taking it down for winter protects the mesh from snow load and ice.

Warranty, Booking and How the Price Is Set

Here is what stands behind the work, how a visit is arranged and at what point the figure becomes final, so nothing about the terms comes as a surprise later.

What the Warranty Covers and Who Does the Work

Our own crew does the work, and we give a 1-year warranty on window repair that covers both labour and replaced parts. The same team handles the Swedish seal groove, the hardware adjustment and the painting, so no stage passes to a third party. For a bigger job, window installation carries a 5-year warranty and glass unit replacement a 3-year one, which tells you how we separate a repair from a full swap. The 1-year term applies to the repair itself, whatever the age of the timber or the profile it sits in. A warranty tied to the crew that did the job means the same people come back if something needs redoing, with no handover between firms.

Booking a Free Measure and Paying After the Work

  • Free measuring: the measurer comes at a time that suits you, takes the sizes and helps choose the design, mesh and fixings.
  • Fixed price: the figure is written into the order after measuring, so the amount you agree is the amount you pay.
  • Fast replies: we answer on WhatsApp within 5 minutes, seven days a week, and confirm the visit slot there.
  • Payment after installation: you settle by cash, card or Kaspi once the work is finished and checked.
  • No surprise extras: hardware, seal and paint discussed at the measure are already inside the agreed order.

When wooden window repair is justified

A wooden window seldom fails all at once — it gives way at a single joint, seal or hinge. The points below help you judge your own frame before anyone visits.

  • Sash movement: open and close each leaf by hand; a leaf that drags or needs a shoulder to lift usually signals worn hinges, not a dead frame.
  • Seal condition: run a finger along the groove — caulking that crumbles or pulls away lets cold air through and gets replaced, not patched.
  • Wood soundness: press a screwdriver tip into the lower corners; soft, spongy timber means rot has gone past the surface.
  • Glass and putty: look for cracked panes, loose glazing beads and gaps where putty has dried and fallen away.
  • Draft test: hold a strip of paper at the meeting rail on a windy day — fluttering shows exactly where the leak sits.

Questions about wooden window repair in Temirtau

Repair or replacement, seal, sagging sash, insulation and painting

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can an old wooden window be repaired or is it easier to install a new one?

If the frame and sashes are intact, without rot or deep cracks, repair will restore warmth to the window without replacing it. Replacement is worth considering when the geometry is compromised and restoration is no longer practical.

02Can a modern seal be fitted into a wooden window and how long does it last?

Yes, a modern seal is installed in the wooden frame and the window stops letting in drafts. The service life depends on the sash and care, usually several years.

03What to do if the sash of a wooden window has sagged and does not close tightly?

The sagging sash is removed, the hinges and fixings are straightened, and if necessary tightened and adjusted. After fitting, the window closes tightly again without distortion.

04How to insulate a wooden window so it does not freeze in winter during severe frosts?

Replacing the seal, insulation using the Swedish method, and sealing gaps in the frame help. What exactly your window needs will be shown by a specialist's inspection.

05Can a mosquito screen be installed on a wooden window and how is it attached?

Yes, the screen is mounted on the wooden frame using Z-brackets, plungers or magnets, with fixings selected to match the profile. The wood is not damaged, and the screen is removed from the inside for the winter.

06Do wooden windows need painting and how often should this be done?

Yes, paint protects the wood from moisture and drying out, so the coating should be renewed as it wears, usually once every few years. The exact interval depends on the window and operating conditions.

Reviews of wooden window repair in Temirtau

5,0based on 97 reviews on platforms
All reviews