Craftsman holding a roll of brown window seal in the kitchen
from 1 000 ₸ per linear mWe don't remove the window, just replace the seal: in one visit, with adjustment and a 1-year warranty.Calculate

Window Seal Replacement in Temirtau

PVC windows · Flat

EPDM seal

A tight new contour keeps out both the steppe wind and street grime. From 1 000 ₸ per linear m.

Technician holds a coil of black rubber window seal
GoogleYandex MapsZoon

5,097 reviews on review sites

What window seal replacement in Temirtau gives you

The rubber in the grooves wears out before the frame. By replacing it, you get a warm and clean window without big expense.

Why replace

The seal is laid along the grooves of the frame and sash and closes the gap when the window is closed. Worn rubber hardens and cracks, and through the loose contour frosty air, street grime and moisture get into the flat.

Temirtau has cold windy winters, and the air near the industrial city carries fine dust, so a tight contour is especially important here. The technician will fit the seal to your profile and set the pressure for winter.

Hand fits a new black seal into the groove of a white sash
from 1 000 ₸

linear metre of seal including labour

1 year

warranty on repair and components

any

window brands: KBE, Rehau, VEKA, Provedal

Profiles
KBERehauVEKAProvedalOthers

How seal replacement in Temirtau is performed

Four problems people write to us about.

A palm at the edge of a closed sash checks where the draft comes from
  • 01Cold from the balcony

    The balcony door seal has worn out, and cold air blows across the floor.

  • 02Paint on rubber

    The seal painted over during repairs has hardened and no longer holds the sash.

  • 03Sash freezes

    Ice on the contour means warm air is escaping through gaps.

  • 04Dark grime

    Soot on the windowsill with the window closed is a sign of a loose seal.

Types of seal contours for Temirtau windows

For north-facing and windy windows — frost-resistant rubber, for the loggia — brush or door contour, for the bedroom — an inter-frame layer.

EPDM

PVC windows in a flat

Technician holds a coil of black rubber window seal

The standard rubber fits almost any profile and doesn't crumble in the cold.

from 1 000 ₸/linear m

Frost-resistant

north, windy side

A craftsman holds a coil of grey rubber window seal in his hand

Rubber from Germany stays soft in the severe cold of a steppe winter.

from 1 200 ₸/linear m

Door

balcony exit

A craftsman holds a strip of brush window seal with bristles in his hand

A thick wear-resistant contour for a sash that works every day.

from 5 000 ₸/unit

Brush

aluminium loggia

A length of black self-adhesive window seal on a master's palm, white backing paper peeled back at the end

Dense bristles on the runners keep snow and dust from getting inside.

from 1 150 ₸/linear m

Inter-frame

bedroom, children's room

A craftsman holds a thin strip of double-glazed window seal in his hand

Another line of rubber between frame and sash keeps warmth in better.

from 2 800 ₸/window

Window seal replacement prices in Temirtau

The price depends on the length of the contour and the type of seal; the technician will give you the exact quote after inspection.

Type of workPrice
EPDM window sealmain contourfrom 1 000₸ per linear m
German frost-resistantfor cold wintersfrom 1 200₸ per linear m
Full window resealframe and sashfrom 3 500₸ per window
Balcony doorfull contourfrom 5 000₸ per unit
Brush sealaluminium framesfrom 1 150₸ per linear m
Cleaning and lubricationsoft rubberfrom 750₸ per linear m
Inter-frame contourtighter windowfrom 2 800₸ per window
Draught proofingsealing gapsfrom 3 500₸ per sash
Winter adjustmentsash pressurefrom 3 000₸ per sash
Liquid plasticseams and jointsfrom 1 500₸ per linear m
Wooden frame insulationSwedish technologyfrom 4 200₸ per linear m

The price is fixed in the order after measurementMeasurement and consultation are freePayment after installation: cash, card, Kaspi

Call a technician

Why customers order seal replacement in Temirtau from us

What makes working with us convenient.

For a year1 year

we are responsible for the replacement and new seal under warranty

Sealmatched to brand

suitable for KBE, Rehau, VEKA and Provedal profiles

Priceno extra charges

we quote after inspection and put it in the order

Paymentat the end

when the window is checked, by a convenient method or Kaspi

WhatsApp5 minutes

average time we take to respond

Weekendswe work

Saturday and Sunday are also working days

Contact09:00–19:00

during this time we book a technician every day

Experiencesince 2012

we work across Kazakhstan

How window seal replacement is carried out in Temirtau

Four clear steps.

  1. A hand holds a phone with a dark screen near the edge of a white window
    015 minutes

    Request

    Describe in a message what is wrong with the window and take a photo of the sash or door — this will speed up seal selection.

  2. A tape measure lies along the bottom edge of the window opening, close-up view
    02at a convenient time

    Inspection

    We arrive, check the seal, hinges and locking pins, find out the profile brand and give you the price straight away.

  3. Hands holding a piece of new black window seal above a workbench with tools
    03one visit

    Replacement

    We remove the worn contour, wipe soot and dust from the grooves, and install a fresh seal without gaps.

  4. Finished white window in a bright room
    04in your presence

    Check

    We switch the pins to winter mode, check for draughts together with a hand and paper, and only then proceed to payment.

Good to know

Window Seal Replacement in Temirtau

We handle window seal replacement in Temirtau with our own fitters, not subcontractors. A free measuring visit comes first, the fitter matches the seal to your KBE, Rehau, VEKA or Provedal profile, and the work carries a 1-year warranty on labour and replaced parts. You pay after the job is done.

Draft or Worn Seal? Reading Symptoms Before You Order Window Seal Replacement

A closed window that still lets cold air in is the most common reason people call us. The first job is to work out whether the seal has aged or the sash has simply slipped out of adjustment.

Four Signs the Seal Has Aged, Not the Hinge

  • Even draught around the perimeter: cold air creeps in along the whole opening rather than from one corner, pointing to a gasket that lost its spring.
  • Condensation on the inner edge: moisture collects on the warm side overnight because the rubber no longer separates cold outside air from warm room air.
  • Stiff, slick surface: a hardened gasket feels firm and slippery to the touch instead of soft and slightly tacky.
  • Visible flattening or cracks: the profile stays compressed after opening and shows fine splits along the fold, so it no longer springs back.

When the Problem Is Adjustment, Not the Seal

We check the sash first, because a dropped or skewed leaf presses the rubber unevenly and mimics a worn gasket. A leaf that has slipped on its hinges leaves a gap at one corner while the rest of the rubber still sits tight, and the draught follows that single line rather than the perimeter. Our technician opens the unit, looks at how the gasket meets the profile on all four sides, and tests the handle and hinges for play. If the draught disappears after the leaf is re-hung and the rubber still looks intact, replacement is not needed yet — adjustment alone solves it. The same check tells us whether the gasket has genuinely flattened, so nobody pays for new rubber that the unit does not need.

Matching the New Window Seal Replacement to Your Window Profile

The seal has to fit the groove of your profile, not the other way round. This is where most DIY attempts fail, and where a measuring visit pays for itself.

Rubber or Silicone and Which Profile Takes Which

Which gasket type suits each common profile system
ProfileSeal typeWhat we check
KBERubber gasketGroove width and corner joints
RehauRubber or siliconeSash rebate depth
VEKASilicone gasketCompression along the closing line
ProvedalThin rubber cordAluminium channel fit

Plastic, Wood or Aluminium Frames

We service plastic, wooden and aluminium frames, so the material decides the seal and the fixing, not whether the job is possible. On PVC sashes the gasket sits in a factory groove, and our fitter matches its cross-section to the rebate depth of that specific system. Timber units from older blocks of Temirtau often carry a wider groove from decades of seasonal movement, and there a slightly thicker cord restores the compression that a standard one no longer gives. Aluminium frames, including cold Provedal glazing on balconies and verandas, take a narrow cord that will not bind when the metal expands in summer heat. In our practice the frame itself rarely limits the work — the right cross-section and a clean groove do most of it. Checking the groove before ordering saves a second visit.

How Window Seal Replacement Runs from Measuring to Final Check

The visit is short and does not require clearing the whole room. Here is the order of work, what the fitter brings, and how long each stage takes.

Step by Step Through the Visit

The fitter measures, removes the old gasket, sets the new seal around the moving sash and frame, then checks the sash closes evenly. Measuring and consultation are free, and the measurer comes at a time that suits you, takes the sizes and helps pick the seal and fixings. On the day itself he strips the worn rubber from the groove, cleans the channel, presses the new profile into place and runs a finger along the perimeter to confirm it sits flush. The last stage is a closing test on all four sides — the sash should pull in evenly without a gap at the corners. Clear the sill and the floor by the frame before the visit — the fitter needs room to swing it fully open and to test the seal on every edge.

One Sash or the Whole Unit

We replace the seal only where it has failed, but if the gasket has aged on a single sash it is usually near the end of its life on the others too. Rubber and silicone harden at roughly the same rate across a unit, so the sections that still feel soft are often months behind the part that already leaks. Our fitters handle window seal replacement in Temirtau on plastic, wood and aluminium frames, and they check every opening of the unit during the same call rather than just the drafty one. Replacing one movable part now and the rest in a few months costs more in repeat visits than doing the whole unit in one go. Ask the measurer to quote the full perimeter while he is on site — the decision is easier with the whole picture in front of you.

Seal Service Life, Care and What the Warranty Covers

A new seal is not a fit-and-forget part. A little care each season keeps it supple, and the warranty is there for the cases where something does go wrong.

How Long a Seal Lasts and How to Keep It Supple

A gasket that is cleaned and lightly lubricated once or twice a year keeps its elasticity far longer than one left to dry out. Rubber and silicone both harden from dust, sun and the constant pressure of the sash, so the surface loses its give and starts to let air through at the corners first. A damp cloth along the groove removes the grit that grinds the profile every time the sash closes, and a thin film of silicone grease restores the slide. Check the hinge side and the bottom sill channel too, since that is where water sits longest after rain and where mould takes hold. Wipe the seal with a damp cloth and apply a thin silicone grease, not oil — oil softens the rubber and shortens its life.

Warranty, Payment and Booking the Visit

We give a 1-year warranty on window repair, covering both the labour and the parts we replace, and you pay after the work is finished. That warranty applies to every seal we fit, whatever profile the frame carries — KBE, Rehau, VEKA or Provedal — so the age or make of your sash is not a barrier. Payment is cash, card or Kaspi once the job is done and you have checked the sash yourself. The price is fixed in the order after measuring, so the figure you agree at the visit is the figure you pay. We answer on WhatsApp within five minutes and work seven days a week, which means a failed seal on a Friday evening can usually be looked at over the weekend rather than left until Monday.

Repair the Seal or Fit a New Window

Not every draughty window needs replacing, and not every old unit is worth repairing. The frame and the glass unit decide which way to go.

When a New Seal Is Enough and When It Is Not

If the frame is sound and the glass is clear, a new seal plus adjustment restores the unit; if the profile is warped or the pane has failed, replacement is the honest answer. Run a finger along the gasket line and press the sash corner — movement there points to worn hinges, which tightening or new hardware can solve. Warped PVC profiles, rot in timber or a bent aluminium section cannot be sealed back into shape by rubber alone. We replace the glass unit within one day when the schedule requires it, at a surcharge on the pane itself, so a failed double-glazed panel does not force a full swap. Check for fogging between the panes — that is a failed unit, and no seal will fix it.

Getting the Windows Ready for Winter

  • Seal check: we run a hand along every gasket line and press the corners to catch gaps before they widen.
  • Adjustment: hinges and position are corrected so the fresh rubber presses evenly on all four sides.
  • Hardware lubrication: moving parts get new grease, keeping handles and tilt mechanisms free in the cold.
  • Slope and sill review: loose slopes and sills are noted, since cold bridges there undo good work.
  • Timing: book before the first hard frost, as rubber seats more easily in mild weather and follow-up is quicker to arrange.

How to decide on window seal replacement before the cold

A seal that fails evenly, a sash that still holds its shape and glazing that has not fogged are three signals worth checking before deciding what to do next.

  • Read the symptom first: draughts along the whole opening point to the seal, while a cold corner usually means the hardware needs adjusting.
  • Match the seal to the profile: the groove and the frame material decide which rubber or silicone strip fits, not the price tag.
  • Replace around the full perimeter: sealing the moving part and the fixed part together, then checking the closing line, prevents a repeat visit.
  • Keep the gasket supple: wiping it clean and treating it twice a season slows hardening and cracking.
  • Weigh the structure before the seal: a sound profile and clear glazing justify a fresh insert, while a warped leaf or fogged panes point elsewhere.

Questions about window seal replacement in Temirtau

Seal replacement, balcony, sashes, profiles, climate

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can the seal on a balcony door and a loggia be replaced?

Yes, the seal is replaced both on balcony doors and on loggia sashes — the contour is the same, but wear can be faster due to temperature changes. The technician will select the material for the profile and check the door's compression.

02Do I need to remove the sash to replace the seal?

In most cases, the sash does not need to be removed: the old seal is pulled out of the groove and a new one is installed right in place. Removal is only needed when hardware gets in the way or the profile makes it hard to reach the corners.

03Why does the window still let in drafts after the seal is replaced?

If the seal is new but there's still a draft, the cause is usually the sash compression, misalignment, or worn hardware — the seal is no longer the issue. In that case, adjustment or repair is needed, not another seal replacement.

04Can the seal be replaced on an old KBE or Rehau window?

Yes, we replace seals in windows from any manufacturer, including KBE, Rehau, VEKA, and Provedal. For older profiles, we select material based on the groove shape so it fits tightly and stays in place.

05Which seal is best for plastic windows in our climate?

For sharp temperature changes, frost-resistant EPDM is more reliable: it stiffens less and doesn't crack in the cold. TPE is also suitable, but it loses elasticity faster in freezing temperatures — the choice depends on the profile and the side of the window.

06Who replaces seals on plastic windows with a home visit?

We visit your home: the technician will inspect the window, select the seal, and replace it on site. Measuring and consultation are free, and we provide a one-year warranty on the work.

Reviews of window seal replacement in Temirtau

5,0based on 97 reviews on platforms
All reviews