Technician holding a white window handle with a screwdriver on a warm loggia
from 750 ₸ per linear metre of sealWe prepare windows for wind and frost, clean mechanisms from dust, payment after inspection.Calculate

Window Maintenance in Temirtau

Frost · Pressure

Winter mode

We move the pins to tight pressure, and cold wind no longer passes along the edge of the sash. From 3 000 ₸ per window.

A hand turns the sash eccentric with a hex key, switching the window to winter mode
GoogleYandex MapsZoon

5,097 reviews on review sites

What window maintenance in Temirtau is

Wind from the reservoir, frost and fine dust — three reasons why windows here need regular care.

Why

In winter, windows take a beating from wind and frost, while fine dust in the air settles in mechanisms all year round. Grease thickens, pins wear out, rubber hardens, and the sash starts letting in cold.

The master switches windows to winter mode, cleans and lubricates the hardware, treats the seal with silicone and cleans the drainage. After the visit, the window closes tightly and does not freeze along the edge.

A technician wiping the window frame by the handle in a kitchen
from 3 000 ₸

switching a window to winter mode

from 1 250 ₸

cleaning and lubrication of the sash mechanism

1 year

warranty on work and parts

In progress
PressureLubricationRubberDrainageHandles

How window care after winter is performed

Four tasks that most often need solving in Temirtau.

Serviced window in a study, one handle on the sash
  • 01Windows not switched to winter

    We set winter pressure, and frost and cold along the edge of the sash disappear.

  • 02Hardware not lubricated

    We remove dust and old thick grease, apply new grease, and the handle moves easily.

  • 03Going through all windows

    We go through every window in the apartment or office and do everything needed in one visit.

  • 04Seal has hardened

    We treat the rubber with silicone, and if the seal is torn, we offer to replace it.

Types of window care work for Temirtau flats

Choose what you need or ask a technician to inspect your windows and make a list of works.

Winter pressure adjustment

per window

A hand turns the sash eccentric with a hex key, switching the window to winter mode

We reposition the eccentrics and check that the sash is pressed tight all around.

from 3 000 ₸

Dust cleaning

per sash

A technician holds a small brush with silicone lubricant for cleaning the handle and hinge

We clean fine dust out of the mechanism and lubricate the moving parts.

from 1 250 ₸

Rubber seal care

per linear metre

Hands lubricate the window's rubber seal with silicone using a cloth

We treat the seal with silicone so it does not crack in freezing weather.

from 750 ₸

Draught-proofing

per sash

A hand checks with a strip of paper whether air blows from under the window sash

We find where the draught comes from and adjust the sash so the gap is gone.

from 3 500 ₸

Thermal imaging

per inspection

A technician holds a thermal imager to find drafts near the window

We show you on the image where the window loses heat, before any work starts.

from 9 000 ₸

Window maintenance prices in Temirtau

The cost depends on the number of sashes and works and is fixed before we start.

Type of workPrice
Seasonal maintenance (winter/summer)winter pressurefrom 3 000₸ per window
Cleaning and lubrication of hardwarefine dust in the mechanismfrom 1 250₸ per sash
Cleaning and lubrication of sealrubber carefrom 750₸ per linear metre
Comprehensive window servicewith drainage cleaningfrom 10 000₸ per window
Window service for an apartmentwhole apartmentfrom 6 600₸ per apartment
Elimination of draughtswind at the sashfrom 3 500₸ per sash
Simple sash adjustment during servicinghinges and pressurefrom 3 000₸ per sash
Balcony door adjustmentbalcony doorfrom 6 000₸ per item
Window handle replacementnew handlefrom 2 750₸ per item
Installation of winter (slot) ventilationwinter ventilationfrom 7 600₸ per item
Thermal imaging inspection of windowscold spotsfrom 9 000₸ per job
Master's visit and inspection (without repair order)window inspection onlyfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after the work: cash, card, Kaspi

Book a technician

Why customers order window care from us in Temirtau

What applies on every technician visit.

Repair warranty1 year

for the work and for the parts we replaced

Amountin the order

fixed after measuring and not changed along the way

Paymentafter

you have checked the windows: cash, card, Kaspi

WhatsApp5 minutes

usual response time to a message

Scheduleno days off

the technician will come on weekdays and at weekends

Brandsany

seal for KBE, Rehau, VEKA, Provedal and other profiles

Windowsall types

plastic, wooden and aluminium

Screenswe will remove

take off mosquito screens for winter and put them back in spring

How window maintenance is carried out in Temirtau

Four steps from a message to warm windows.

  1. A hand holds a smartphone with a dark screen next to a white PVC window
    01reply in 5 minutes

    Request

    You write on WhatsApp where the draught is, what squeaks or does not close, and how many windows you have.

  2. A tape measure measures the window opening, a hand holds the measuring tape by a white window
    02on a convenient day

    Inspection

    The technician checks the pressure, mechanisms, rubber seal and drainage and gives the price for each job in advance.

  3. Hex keys and lubricant on a table
    03in one visit

    Servicing

    Switches the windows to winter mode, cleans and lubricates the fittings, treats the seal and cleans the grooves.

  4. A serviced white window in a dining room, a table in the foreground
    04before payment

    Check

    You close the windows yourself and check that there is no draught at the edge, and then you pay.

Good to know

Window Maintenance in Temirtau with a Free Measuring Visit

We handle window maintenance in Temirtau with our own fitters, not through an agency. We diagnose the fault first, then adjust the sash, replace the seal matched to your profile, or swap a glass unit, with a free measuring visit, payment after the work and a 1-year warranty on repair labour and replaced parts.

How window maintenance tells what your window needs before anyone arrives

A draught, a sash that catches, and fog between the panes are three different problems with three different fixes. Working out which one you have before a fitter arrives points the job in the right direction.

Three Symptoms and What Each One Usually Means

  • Draught along the edge: a cold stream at the perimeter usually means the gasket has lost its grip or the panel has dropped out of square.
  • Sash catching or scraping: the frame is rarely at fault — the hardware has shifted, and the leaf needs realigning on its hinges and cams.
  • Fog between the panes: mist trapped inside the unit is a sealed-cavity failure that no realignment will clear.
  • Paper test: press a sheet into the gap with the sash shut; if it slides out easily, the gasket is worn, if the leaf sits unevenly, alignment is the cause.

When Adjustment Is Enough and When a Part Has to Be Replaced

We adjust the sash on its hinges and cams first, because most draughts and scraping edges are a matter of alignment rather than a broken part, and replace cams, hinges or handles only when the metal is worn or cracked. Adjustment restores the seal's grip without new components, while a worn cam or a hairline crack keeps failing however often it is tightened. On window repair we give a one-year warranty on labour and replaced parts, so the distinction matters for what is covered. A leaf adjusted repeatedly in the same direction is a sign the hinge is bending, and by then a new one outlasts another round of tightening.

What a Window Maintenance Visit Covers Step by Step

A maintenance visit is not a single operation but a sequence: inspection, adjustment, replacement of whatever failed, then a check that the sash closes tight. The list depends on what the fitter finds.

From the First Message to the Final Check

We reply on WhatsApp within 5 minutes, agree a convenient time for the free measuring visit, and the fitter arrives with the seals, locking hardware and fasteners needed for the profile he expects to find. Consultation happens on the spot: sizes, the condition of the seal line, and whether the frame is worth adjusting or part of it has to be replaced. The price is fixed in the order after measuring, so any extra part found on the day is agreed with you before it goes on rather than added to the bill afterwards. We are open seven days a week, and payment follows installation — cash, card or Kaspi. This is how a window maintenance visit in Temirtau is organised from the first message to the final check.

What the Fitter Checks on the Sash Itself

  • Seal line: a sheet of paper runs around the perimeter to find gaps where air passes.
  • Locking points: each is tested for even pressure and adjusted if it pulls.
  • Handles: loose or stiff ones are tightened or replaced, since wear stops the mechanism turning.
  • Drainage slots: the channels under the moving leaf are cleared so water leaves instead of standing.
  • Glass unit: checked for fog between the panes and for loose glazing beads.
  • Final test: the paper test is repeated and the unit opened and closed several times, because a leaf that seals on one side and leaks on the other has not been fixed.

Seals matched to the profile you already have for window maintenance

The seal is the part we replace most often, yet a new strip only works when it matches the profile groove it sits in. A unit fitted by another company is no obstacle to that.

Why the Seal Has to Match the Profile

We replace the seal on units of any manufacturer, including KBE, Rehau, VEKA and Provedal, because the strip is matched to the groove width and profile depth rather than to the company that installed it. The channel on a Rehau sash is not the same as on a VEKA frame, and a standard roll pressed into the wrong one leaves gaps at the corners. Our fitter measures the channel, the sash depth and the closing pressure before cutting anything, then seats the rubber so the sash closes on an even line all round. A strip that is close but not exact will compress unevenly, so the unit can start draughting again within a season even though the rubber itself is new.

How Often a Seal Really Needs Changing

  • Hardness: press the rubber with a fingernail — if it no longer springs back, it has aged and stopped sealing.
  • Flat spots: compressed bands along the closing line, usually at the handle side and corners where the sash presses hardest.
  • Pulled edges: a strip lifting out of its channel at the corner lets air through even when the rest looks fine.
  • Draught or whistle: a cold stream or high-pitched sound at the corner appears long before the rubber visibly crumbles.

Glass units fogging and same-day window maintenance replacement

Moisture trapped inside a sealed glazing panel is a separate problem from condensation on the room-side surface, and it is solved by replacement rather than repair. Here is how to tell the two apart and what a swap involves.

Fog Inside the Unit Is Not the Same as Fog on the Glass

Moisture trapped between the panes means the sealed unit has lost its grip and cannot be repaired, only replaced, while condensation on the room-side glass is a ventilation and humidity issue. Such a panel is built from two or three sheets held apart by a spacer, with a sealed air or gas chamber inside; once that perimeter seal fails, room air enters and drops its moisture on the cold outer sheet. Streaks, a white haze or droplets that never clear are the signature. Condensation on the inner surface, by contrast, wipes away and returns when cooking, drying laundry or cold nights push indoor humidity up. A failed panel still insulates reasonably at first, so the practical trigger for a swap is the point where the mist becomes permanent rather than seasonal.

What We Replace and How Fast

matching visible symptoms to the likely cause
What you seeWhat it means
Mist or droplets between panesSeal failed, panel needs replacing
White haze or streaks insideCoating or desiccant spent, replace
Fog on the room-side glass onlyHumidity and ventilation, not the panel
Fog that clears in mild weatherEarly seal failure, plan a swap

Getting Windows Ready for Winter and Keeping Children Safe

Autumn is the practical moment to look at seals, hardware and glazing before the cold arrives. The same visit that prepares a window for winter can also make it safer for children.

A Short Autumn Check Before the Cold Sets In

  • Seal line: run a hand along the rubber and look for flattened spots, corner gaps and hardening.
  • Closing pressure: confirm the moving panel presses evenly all round, with no draught at either side.
  • Drainage slots: clear the channels under the leaf so meltwater drains outside instead of pooling.
  • Glass units: check the glazing is still clear, with no haze trapped between the panes.

Restrictors, Locks and Screens on the Same Visit

We fit restrictors, locks and grilles that hold the sash in a safe position, and the fitter checks that the mosquito screen and its fasteners still sit clear of the restrictor. A restrictor limits how far the leaf opens, a lock keeps the handle fixed, and a grille adds a physical barrier on lower floors where a child can reach the opening. The fitter measures the mesh frame, the brackets and the restrictor travel together, because a fitting that fouls the screen pushes it out of line every time the sash closes. A restrictor that catches the screen frame is the most common reason a mesh gets bent, so the two are measured on one visit rather than fitted separately.

Warranty, Payment and Working with a Direct Contractor

A guarantee and a clear payment sequence are what separate a direct contractor from a bare advert, and both are agreed before any work starts, not afterwards.

What the Warranty Covers and for How Long

warranty periods by type of work
WorkCover
Window repair, labour and replaced parts1 year
Glass unit replacement3 years
Window installation5 years

When You Pay and Why It Matters

You pay only once the job is finished, by cash, card or Kaspi, and the price is locked in the document drawn up after the free measuring visit, so nothing is added once the fitter is on site. The measurer arrives at a time that suits you, takes the sizes and helps pick the design, mesh and fixings, and that signed sheet is what the invoice follows. A fitter paid at completion has a reason to run the paper test and the open-and-close check before leaving, which is exactly the step a prepaid job tends to skip. That final check catches the small misses that turn into draughts by midwinter.

Deciding on servicing without extra costs

A window rarely fails all at once. One part gives way first, and the whole flat starts to feel it. The short list below sums up the order in which most faults are found and fixed.

  • Start from the symptom: a draught suggests the gasket, a sash that catches suggests alignment, and fog between the panes suggests the glass unit.
  • Match the part to the profile: a gasket cut for a different profile seats badly and lets air through within a season.
  • Book the check before the cold: adjustment and a fresh gasket in autumn save a full repair in spring.
  • Ask what the warranty covers: labour and replaced parts are separate items, and the terms differ between repair and replacement.
  • Fix the hinges and handles too: worn hardware undoes a good gasket faster than any other single fault.

Questions about window maintenance in Temirtau

Maintenance, adjustment and protection of windows

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01What does the maintenance service for uPVC windows include?

Standard care includes lubricating the hardware and seal, adjusting the sashes and the pressure, and checking that the locks and handles work. If needed, the technician replaces worn parts and gives advice on care.

02How often should uPVC windows be serviced?

It is enough to carry out preventive maintenance once or twice a year, preferably before the heating season and after winter. If the windows are opened frequently or are in the kitchen, the technician may recommend more frequent care.

03Why have the windows started to let in draughts and how can this be fixed?

Most often the draught is caused by loose sash pressure or a hardened seal. Adjusting the pressure and replacing the seal solve the problem without replacing the window.

04Can a window be adjusted if the sash catches on the frame?

Yes, this is one of the most common reasons for calling a technician. Adjusting the hinges returns the sash to the correct position and it stops catching on the frame.

05How is window maintenance carried out and how many visits are needed?

Usually the technician comes once and performs all the work on site: lubrication, adjustment, checking. A second visit is needed only if a part or a double glazing unit has to be ordered to size.

06How can windows in Temirtau be protected if there is a small child in the home?

Opening limiters and blockers are installed on the sashes, and the handle is replaced with a lockable model. Such devices prevent the child from opening the window wide but still allow ventilation.

Reviews of window maintenance in Temirtau

5,0based on 97 reviews on platforms
All reviews