Craftsman by a plastic window with double-glazed units in the living room
from 1 300 ₸We remove the damaged glass together with the old unit, while keeping the frame, handle and reveals.Calculate

Double Glazing Replacement in Temirtau

Children's room

Laminated

Film-bonded glass produces no shards on impact. A simpler option is security film on standard glass from 8 000 ₸ per m².

White PVC window in a children's room with a wooden bed
GoogleYandex MapsZoon

5,097 reviews on review sites

What is double glazing replacement in Temirtau

Only the glass is damaged, so the whole window doesn't need replacing. The new unit fits into the same sash.

About the work

Scratches, chips and cracks can't be repaired, but the unit is easy to remove from the sash. The technician takes off the glazing beads, removes the old unit, installs a new one to the surveyor's measurements on spacers and puts the beads back.

Winters in Temirtau are windy, and industrial dust scratches glass over time. When replacing, you can immediately install a double-chamber unit for warmth, laminated glass for a children's room or frosted glass for a window facing neighbours.

Empty PVC window sash against the wall and removed glazing beads on the floor next to a balcony door
from 19 500 ₸

new unit per square metre

3 years

warranty on unit and work

free

measuring and glass selection on site

Glass types
LaminatedFrostedTintedCoatedStandard

How glass replacement in Temirtau is performed

Four common reasons for calls from Temirtau.

A craftsman inserts a white glazing bead into the sash with a rubber mallet
  • 01Safety concerns

    In children's rooms we install laminated glass that cracks on impact but stays in the frame.

  • 02Scratched glass

    Dust, abrasives and harsh sponges leave scratches that can't be polished out, so we replace the unit.

  • 03Chip after renovation

    The window was hit during finishing and a crack spread from the chip, so we install a new unit without removing the frame.

  • 04Crack on the balcony

    On a cold balcony glass cracks from frost and wind, so we replace it in the same frame.

Types of glass for a new unit in Temirtau

Five options: warmth for winter, safety for children and privacy for windows facing neighbours.

Double-chamber

living rooms

White PVC window in winter, a snowy courtyard outside, a floor lamp and a small table beside it

Three panes retain heat in windy frosts, so it's not cold by the windowsill.

from 20 000 ₸/m²

Coated

corner apartments

White PVC window in a home office, a desk with a laptop and a lamp in the foreground

Energy-saving glass reflects radiator heat back into the room.

from 15 200 ₸/m²

Single-chamber

country house, balcony

White PVC window in a dining room, with an oak table and chairs next to it

A lightweight two-pane unit for unheated spaces.

from 12 600 ₸/m²

Security film

children's room

Hands apply a clear protective film to a window glass with a squeegee

Transparent film holds shards together if the glass is broken.

from 8 000 ₸/m²

Tinting

windows facing neighbours

A plastic window with tinted glass, houses and mountains visible through the glass

The film hides the room from prying eyes and softens bright sunlight.

from 5 500 ₸/m²

Double glazing replacement prices in Temirtau

The final price depends on the glass size and unit type; we fix the amount after the measuring visit.

Type of workPrice
Double glazing replacement, per m²unit made to sash measurementsfrom 19 500₸ per m²
Double-chamber double glazingwarmer in windy wintersfrom 20 000₸ per m²
Single-chamber double glazingcountry house, balconyfrom 12 600₸ per m²
Energy-saving double glazingcoated glassfrom 15 200₸ per m²
Glass in PVC balcony doorwith hinge adjustmentfrom 22 000₸ per m²
Broken glass replacementif the second pane is intactfrom 8 000₸ per m²
Security film applicationchildren's roomfrom 8 000₸ per m²
Tinting filmprivacyfrom 5 500₸ per m²
Glazing bead installationreplacing cracked onesfrom 1 300₸ per item
Sash adjustment with removalfor laminated glass weightfrom 4 000₸ per sash
Call-out and inspectionwithout repairfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after fitting: cash, card, Kaspi

Book a measuring visit

Why customers order a new unit in Temirtau from us

Order terms in Temirtau.

Warranty3 years

on the new unit and fitting

Pricein the order

fixed after measuring and never changed

Measuringfree

we come at a convenient time and help choose the glass

Paymentafter

fitting: cash, card or Kaspi

Urgent1 day

for broken glass, with a surcharge on the unit price

Response5 minutes

on WhatsApp to a photo of the damaged window

We workevery day

we take requests daily

Experiencesince 2012

we work across Kazakhstan

How double glazing replacement is carried out in Temirtau

Four steps from a message to new glass.

  1. A hand holds a phone with a dark screen by a plastic window for measuring
    01reply in 5 minutes

    You message us

    Send a photo of the glass on WhatsApp and tell us what you need: safety, privacy or just an intact window.

  2. A tape measure measures the sash opening of a white plastic window, only hands are visible
    02free

    Measuring

    The surveyor measures the glass, checks the profile and glazing beads and shows you glass options.

  3. Hands assemble a glass unit from glass panes and an aluminum frame on a workbench
    03urgent — one day

    Manufacturing

    The unit is made to measure; if the glass is broken, we make and fit it within a day with a surcharge.

  4. A new glass unit is installed in a white plastic window sash, clean glass
    04payment after

    Fitting

    The technician replaces the unit, refits the glazing beads, adjusts the sash, and then you check the window and pay.

Good to know

Double Glazing Replacement in Temirtau

We handle double glazing replacement in Temirtau with our own fitters, a free measuring visit and a 3-year warranty on every new sealed unit. We replace only the glass unit and keep your existing frame, fit plastic, wooden and aluminium windows, and can make and fit a unit within one day when you need it urgently.

How to Tell a Failed Sealed Unit from Condensation or a Worn Seal in Double Glazing Replacement

Most calls start with a sweating window or a draught. First, work out whether the sealed unit has failed or the seal and hardware around it are worn.

Fog between the panes or fog on the room side

Moisture trapped between the panes means the sealed unit has lost its seal and cannot be repaired, while fog on the room side is ordinary condensation from humid indoor air meeting a cold surface. When the edge fails, damp air slips past the spacer bar, the desiccant saturates within weeks, and the cavity clouds from the bottom corner upward. Room-side mist appears on humid days, runs down the pane and clears once you ventilate, while a failed assembly keeps its haze in dry weather too. Wiping the inner surface tells you nothing, so check the spacer bar for a milky or corroded look before ordering a glazing replacement.

When draughts come from the seal or the hardware

  • Worn gasket: a hardened or shrunk strip lets cold air slip past the frame along the whole edge.
  • Loose hardware: handles needing a second push or sagging hinges leave the sash slightly open.
  • Failed pressure: an out-of-alignment sash makes locking points miss their keeps, widening the far corner gap.
  • What we do: we replace seals in windows of any make, including KBE, Rehau, VEKA and Provedal, without touching the glass.

A quick check before you book a visit

  • Fog that never clears: haze sealed between panes in dry weather means spent desiccant and a failed edge.
  • A cracked pane: any break lets moisture into the cavity, so the assembly fails faster than a patch holds.
  • Corroded spacer bar: a white, powdery or blistered edge shows the seal has been breaking down.
  • Fog returning after a repair: mist within days means the panel was patched, not resealed.

Choosing a Glass Unit for Double Glazing Replacement That Fits Your Room and Your Window

Choosing comes down to three things: how many chambers the glazing has, which pane goes inside and what the space needs most for a bedroom, child's room or street-facing window.

Single-chamber, double-chamber and energy-saving glass

  • Single-chamber: two panes and one air gap, light for slim sashes and mild spaces.
  • Double-chamber: three panes and two gaps, holding warmth better through a Temirtau winter and cutting outside noise.
  • Energy-saving glass: a low-emissive coating reflects warmth back inside instead of letting it escape.
  • Weight check: each extra chamber adds kilograms, so a wide sash on older hardware may need a lighter formula.
  • Best fit: the two-chamber version with an energy coating covers most flats, while a single-chamber one suits glazed balconies and interior partitions.

Matching the unit to the room

Which glazing suits which space
Room or windowWhat matters mostSuggested glazing
Child's roomWarmth and safetyDouble-chamber with energy-saving glass
Street-facing windowQuietDouble-chamber with a thicker outer pane
Shaded flatDaylightSingle or double-chamber with clear glass
Balcony doorStrengthDouble-chamber, toughened lower pane

Frames we fit new units into

We fit replacement glazing into plastic, wooden and aluminium frames, and in most cases the frame stays exactly where it is. On plastic systems the old glazing bead usually clicks out cleanly and goes back over the new panel; on aluminium profiles the bead is often held by a rubber gasket that we renew at the same time. Wooden frames behave differently, since the bead is nailed or pinned and on an older sash it often splits when prised off. That is why during measuring we inspect the rebate and the bead, then bring a matching replacement rather than leave the panel sitting loose.

How the Double Glazing Replacement Runs from Measuring to Handover

A double glazing replacement runs in a few clear steps, and the opening is almost always closed before fitters leave. Below is how measuring, making and fitting go, including the urgent option.

The free measuring visit

  • Free measuring and advice: the measurer arrives when convenient and helps pick glass and fixings.
  • Sizes from the frame rebate: we read the opening from the rebate, not old glass, so the panel isn't cut too tight.
  • What gets checked: sill level, frame square and rebate depth, so beads seat without gaps.
  • Fixings chosen on site: the measurer picks the fastening for your profile and floor: Z-brackets, pins or magnets.
  • No obligation: the visit costs nothing, and the price is fixed only after measuring.

Making and fitting the new unit

  • Standard schedule: the sealed unit is made to measured size and fitted on a normal lead time.
  • Urgent replacement: a double glazing replacement in Temirtau can be made and fitted within one day for a surcharge.
  • Old panel removal: the failed one comes out, the rebate is cleaned, and the new one goes in during the same visit.
  • Sealed the same day: the opening is closed before the team leaves, so the flat is never left open overnight.
  • Beads and sash: the glazing beads are pressed back and the sash is opened and closed to confirm it runs clean.

Checking the finished job

  • Flush fit: the new panel sits flush in the rebate, with no step against the frame.
  • Beads seated: every glazing bead is pressed home and level, with no fingernail gap.
  • Draught test: the closed sash is checked at the seal line for air movement.
  • Sealant left to set: leave a freshly fitted panel for a day before cleaning, so sealant cures undisturbed.
  • Handover walk-through: fitters show how the sash opens and how to air the room without straining the fresh seal.

Replacing the Unit or the Whole Window

Homeowners often ask whether the entire window must come out. Usually it does not: if the frame and sash are sound, only the sealed unit is swapped.

Keeping the frame and changing only the glass

We replace just the sealed unit and keep the frame and sash, which is faster and less disruptive than a full window swap. The old glazing beads come off, the new panel goes in, and the beads are refitted with fresh seals along the perimeter. Because the surround stays anchored in the wall, there is no re-plastering of the reveal, no repainting of slopes and no re-tiling around the sill — one visit instead of two. Our fitters work on plastic, timber and aluminium surrounds alike. The sash stays hung on its hinges throughout, so the opening is never left without glass for longer than the swap itself takes.

When the whole window makes more sense

  • Warped profile: a surround twisted out of square stresses fresh glass, and seals fail early.
  • Rotten or soft corners: crumbling timber or soft PVC at welds cannot hold a new pane securely.
  • Leaking joints: water at corner welds points to the surround, not the glass.
  • Failed hardware: sashes that no longer close flush mean the assembly is past saving.
  • Draughts from the frame line: cold air there, not at the glass edge, signals the whole assembly has had it.

Warranty, Payment and What Happens After the Fitters Leave

Most people check warranty and payment terms before booking. Below is what our warranty covers, how you pay, and how to look after the fitted pane once fitters leave.

What the 3-year warranty covers

  • Glass unit replacement: every new sealed unit carries a 3-year warranty; window installation carries 5 years.
  • Window repair: repair work is covered for 1 year on labour and replaced parts.
  • What the unit warranty covers: fogging, seal failure and defects inside the sealed unit, not accidental glass breakage.
  • Keep the paperwork: the order and measuring sheet record the exact size and formula fitted, so store them with the flat.
  • Who to contact: message our team on WhatsApp; we reply within 5 minutes during opening hours, seven days a week.

Payment and winter fitting

  • Payment after installation: pay by cash, card or Kaspi once the job is finished and checked.
  • Fixed price: locked in the order after measuring, so the agreed figure is what you pay.
  • Winter work: units are replaced in cold weather if the opening is closed again the same visit.
  • Scheduling: winter jobs are planned so new glass goes straight back in and the room is never left open to frost.
  • Same-day option: urgent broken pane replacement is possible within one day for an extra charge.

Caring for the new unit

  • Ventilate daily: open sashes briefly morning and evening so humid air escapes rather than settling on glass.
  • Wipe with a soft cloth: microfibre and plain water keep surfaces clear; abrasive pads scratch.
  • Check the seal: run a finger along the gasket twice yearly; report hardening or gaps before draughts.
  • Keep vents clear: furniture and heavy curtains against the frame block airflow and cause room-side fog.
  • Airflow beats cleaning products: trapped humid air, not dirt, fogs a healthy pane on the room side.

What to check before double glazing replacement in freezing weather

Replacing a sealed pane is a decision you can narrow down before anyone knocks on your door. Five checks cover most of the ground.

  • Fog between the panes: moisture inside the glazing means the seal failed and replacement is due; room-side fog is usually condensation.
  • A draught on its own: air past the sash points to the seal or hardware first; check glass after.
  • Usage before thickness: match glazing to how the space is lived in, not the deepest option.
  • Sound frame, fresh glazing: keep a straight, dry frame and change only the sealed glass.
  • Terms before the visit: read warranty coverage and payment order ahead, so handover holds no surprises.

Questions about double glazing replacement in Temirtau

Double glazing replacement, diagnostics, timelines, frost

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can I replace just one double glazing unit in a sash instead of all at once?

Yes, you can replace one double glazing unit without touching the others. The technician will measure that specific sash and make a new unit to fit it. The other windows will stay as they are.

02How can I tell if the problem is in the double glazing unit and not in the seal or hardware?

If there is moisture inside the unit or it fogs up between the panes, the issue is with the unit itself. When there is a draft around the perimeter or the sash doesn't close properly, the seal or hardware is likely worn out. The surveyor will determine the exact cause during inspection.

03What should I do if the double glazing unit is cracked or broken, and can a single pane be inserted?

If cracked or broken, the entire double glazing unit is replaced because the seal is compromised. A single pane cannot be inserted: the unit would lose its seal and stop retaining heat. We manufacture a new unit to your dimensions.

04How long does it take to replace a double glazing unit if I am at home with a child?

The replacement of one double glazing unit takes about half an hour, but the exact time depends on the window. The technician will carefully remove the old unit and install the new one in your presence without making excessive noise. The child can stay in another room.

05Can I order double glazing replacement in Temirtau if it is freezing outside?

Yes, we replace double glazing units in Temirtau during the cold season as well. We work carefully to avoid cooling the room: removal and installation take little time. The warranty on double glazing replacement is 3 years.

06Which double glazing unit is best for a frosty winter?

For a frosty winter, a double-chamber double glazing unit with energy-efficient glass is usually chosen. It retains heat better and reduces the risk of fogging. A single-chamber unit is suitable for less cold spaces, such as a balcony.

Reviews of double glazing replacement in Temirtau

5,0based on 97 reviews on platforms
All reviews