Sash adjustment
We tighten the compression and hinges so draughts no longer come from under the sash. Simple adjustment — from 3 000 ₸ per sash.


Sash adjustment
We tighten the compression and hinges so draughts no longer come from under the sash. Simple adjustment — from 3 000 ₸ per sash.

Seal replacement
A new seal restores airtightness around the perimeter. Work — from 1 000 ₸ per linear metre.

Handle replacement
We fit a new handle in place of a broken or sticking one. Replacement — from 2 750 ₸ per item.

Double glazing replacement
We replace a cracked or internally misted double glazed unit. Work — from 19 500 ₸ per m².

Window insulation
We eliminate draughts and cold spots around the perimeter. Insulation — from 1 000 ₸ per job.

5,097 reviews on review sites
We restore the parts responsible for compression, sash movement and airtightness around the perimeter
Window repair covers the sash, hardware and compression seal. Replacing the window itself is needed when the profile or frame is damaged or deformed, while reveal finishing is a separate service not included in repair. If the problem is in the double glazed unit, it is replaced rather than repaired.
Work is divided into adjustment and part replacement. Adjustment restores correct sash movement, while part replacement removes wear: a new seal, handle, hinges or double glazed unit keeps the heat in and outside air out again.

seal per linear metre
simple sash adjustment
warranty on work and components
The work sequence from initial check to test opening of the sash

The technician opens and closes the sash, checks compression around the perimeter, handle movement and seal condition.
Tightens the compression, sets the hinges so the sash moves smoothly and does not catch the frame.
Replaces the handle, hinges, seal or double glazed unit if the old ones cannot be restored.
The old double glazed unit is removed, the new one is fitted into the frame and its alignment around the perimeter is checked.
Five types of work: from simple adjustment to double glazing replacement and perimeter insulation
Compression and hinges

Restores tight compression and smooth sash movement without replacing parts.
Perimeter contour

New seal stops draughts along the sash and frame.
Replacement when broken

We fit a new handle to replace a broken or jammed one.
Crack and condensation

We replace the whole double glazing unit if the glass is cracked or fogged inside.
Draughts and freezing

We eliminate draughts and freezing around the window perimeter.
Window repair price list: work, unit and completion time
| Type of work | Price |
|---|---|
| Call-out and inspection by a technicianwithout ordering a repair | from 3 600₸ per job |
| Simple sash adjustment | from 3 000₸ per sash |
| Complex adjustment with sash removal | from 4 000₸ per sash |
| Window handle replacement | from 2 750₸ per item |
| Hinge replacement | from 4 750₸ per item |
| Hardware repair | from 7 800₸ per job |
| Hardware replacement on sash | from 10 000₸ per sash |
| Seal replacement | from 1 000₸ per linear metre |
| Double glazing replacement | from 19 500₸ per m² |
| Broken glass replacement | from 8 000₸ per m² |
| PVC window sill installation | from 5 500₸ per linear metre |
| Window flashing installation | from 3 250₸ per linear metre |
| Mosquito screen repair | from 2 500₸ per item |
| Air inlet valve installation | from 6 000₸ per item |
Price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card or Kaspi
Book a repairFacts about the company that matter when ordering window repair
We work across Kazakhstan.
We give a 1-year warranty on work and replaced components.
5-year warranty on window installation.
3-year warranty on double glazing replacement.
The measurer will come at a convenient time and help you choose a solution.
You can order in 17 cities of Kazakhstan.
We reply on WhatsApp within 5 minutes.
We replace seals in windows of any manufacturer: KBE, Rehau, VEKA, Provedal and others.
Four steps from request to checking the work

Describe the problem on WhatsApp or by phone: draughts, sagging sash, cracked double glazing.

The master arrives, checks the hardware and perimeter, identifies the cause of the fault and the way to fix it.

Adjusts the sash or replaces worn parts — handle, hinges, seal, double glazing.

The master checks the condition of the hardware and seal with the resident to agree which parts need replacing and which can be adjusted.
Good to know
We handle window repair in Kostanay with our own crews, not through middlemen. We fix plastic, wooden and aluminium windows, replace seals and glass units, and adjust hardware. Measuring and consultation are free, the price is fixed in the order after measuring, and you pay after installation. Every repair carries a 1-year warranty on labour and replaced parts.
Repair almost always costs less than a new unit, but there is a line where patching stops paying off. Here is how a fitter draws that line, and why we never push a replacement you do not need.
We repair a window when the frame and sash are sound and the fault sits in hardware, seals or the glass unit. A handle that turns loosely, a sash that catches on the sill, a draught running along the rebate, mist inside a double-glazed unit — each of these is a part-level problem, not a death sentence for the whole structure. Replacement hardware, a fresh seal or a new glass unit restores the fitting without touching the frame. A sash that still closes flush against the frame after adjustment is the clearest signal the unit has years left in it. Ask the fitter to show you the frame after the sash is opened wide: if the profile is straight and the corners meet tight, the item is worth keeping.
Replacement wins when the frame itself is warped, rotten or cracked, because new parts will not sit true in a damaged base. A bowed profile twists the sash out of square, so hinges wear faster and seals never close evenly. Soft or crumbling timber around the corners, visible splits along a weld, a frame that has shifted after a wall settled — these faults live in the structure, and a repair on top of them buys a few months at best. Repeated repairs on the same corner usually point to a frame problem, not a hardware problem. If a fitter has already adjusted the same sash twice and the draught returns, put the money toward a new unit rather than a third visit.
We repair wooden windows when the timber is dry and solid, and we tell you honestly when a plastic replacement is the better spend. Old wooden sashes respond well to new seals, fresh hardware and a coat of paint, and the repair keeps the look of the building intact. The catch is moisture. Wood that has swollen from moisture often keeps moving after repair, so the decision hinges on how the frame behaves across seasons. Press a screwdriver into the timber at the bottom corner — if it sinks in, the wood is gone and no seal will hold. Dry, firm timber at the joints means the unit has another decade in it.
Every symptom points to a specific part, and reading it correctly saves you from paying for work your window does not need. Here are the most common complaints and what sits behind each one.
A draught at a closed window almost always means a worn seal or a sash that no longer presses evenly, and condensation on the glass follows the same cause. Cold air finds the gap where the rubber has flattened, and the inner pane drops below dew point, so moisture collects along the lower edge overnight. We replace the weatherstripping and check that the opening closes flush against the surround on all four sides. If the gasket looks intact but the draught persists, the fault is usually in the hardware pulling the movable part out of alignment. A five-minute check with a sheet of paper tells you a lot: trap it in the gap and pull — if it slides out without resistance, the closing pressure is failing, and that is the detail worth naming when you call a technician.
A sash that catches the surround or refuses to lock is a hardware alignment problem, and we correct it by adjusting the hinges and locking points rather than replacing parts. The movable panel sags on its hinges over time under its own weight, so the bottom corner drags while the top corner opens a gap. Turning the adjustment screws on the lower hinge lifts it back into square, and the handle then engages without force. After a cold winter the mechanism often needs a fresh adjustment, which is why a unit that worked in autumn can stick by spring. Forcing a stiff handle is the one thing to avoid: the locking cam bends, and a simple adjustment turns into a parts order.
Moisture trapped inside the glass unit means the seal between the panes has failed, and no amount of cleaning will clear it. The haze sits between the layers, not on the surface, and it usually starts as a milky patch in one corner before spreading across the pane. Double-glazed units carry a perimeter seal that ages under sun and temperature swings, and once the desiccant inside is saturated, the mist stays for good. A fogged unit is replaced as a whole, but the outer frame and the movable part usually stay, so the job is smaller than a full swap. Measured and fitted correctly, a new unit restores the thermal performance the assembly had when it was new.
Below are the jobs we carry out and the types of units we handle. The table helps you match your situation to the right kind of work.
| Job | What we check | When it is needed |
|---|---|---|
| Hardware adjustment | Hinge alignment, locking points | The leaf drags or will not close |
| Hardware replacement | Worn or broken mechanism | Handle turns loosely |
| Glass unit swap | Failed sealed cavity | Glass is fogged inside |
| Seal replacement | Gasket compression | Draughts run along the edge |
We replace the seal in units of any manufacturer, including KBE, Rehau, VEKA and Provedal, matching the profile rather than forcing a universal strip. The gasket sits in a groove shaped for a specific system, and its thickness, lip geometry and corner joints differ between lines. On a Rehau frame a strip cut for a VEKA system can seat unevenly, leaving a thin gap along the hinge side that shows up as condensation in cold weather. We take the profile name from the marking or measure the groove before ordering. A seal of the wrong shape can look fine on the roll yet fail within a season, so the match matters more than the brand name.
We repair plastic, wooden and aluminium units, including those on loggias, balconies, verandas and gazebos. Plastic systems take standard hardware and gasket work, timber ones often need the leaf rehung or the wood around the hinge reinforced before new fittings go in, and aluminium profiles on glazed balconies carry lighter mechanisms that wear faster under wind load. We also service small opening sections and the glazing of summer structures, where the frame may have shifted with the seasons. Aluminium on a loggia behaves differently from room units, so the fix is chosen for the frame rather than copied from an indoor job.
From your first message to the final check, a job moves through a few clear steps. Here is the sequence they come in, so you know what to expect and when money changes hands.
Measuring and consultation are free, the measurer comes at a time that suits you, and the price is fixed in the order after measuring. The visit is not a sales pitch: the measurer takes the sizes of each opening, checks the profile and the floor, and helps you choose the design, mesh and fixings that actually fit. Because the figure is locked at that appointment, the sum you agree to is the sum you pay once the work is done, with no renegotiation at the door. Ask for the written document before the crew starts, and keep it — it is the paper the final check is measured against. If you are planning window repair in Kostanay, the same visit sets the scope and the price before any work begins.
We can make and fit a replacement glass unit within a single day when the job is urgent, with a surcharge added to the unit price. A broken or fogged pane leaves the flat exposed, so the workshop treats these requests as priority work rather than slotting them into the normal queue. The swap itself is a short task once the new glazing is on site: the old one is taken out, the rebate is cleaned, and the replacement is set and sealed. Urgent work is worth asking about early in the morning, since the same-day slot depends on when the request reaches the workshop — a message that arrives before noon has the whole working day ahead of it. Send the opening sizes with your first note to save a round of questions.
You pay after installation by cash, card or Kaspi, and we reply on WhatsApp within five minutes, seven days a week. Nothing is due up front, so the sequence runs the other way round from most purchases: the work is finished, you inspect it, and only then does the payment happen. That timing matters, because the final check takes place before any money changes hands — walk the sashes, test the handle and the lock, and look at the seal line along the frame while the crew is still on site. Messages reach us any day of the week, including weekends, so a question about a sticking sash or a draught does not have to wait for Monday. Send a photo with your address and the fault is usually clear before anyone rings the bell.
A warranty is not a slogan on a leaflet but a set of fixed terms tied to specific tasks. Below we break down what is covered, for how long, and why a direct contractor answers differently than a middleman.
| Task | Warranty term | What is covered |
|---|---|---|
| Window repair | 1 year | Labour and replaced parts |
| Glass unit replacement | 3 years | The unit we supply and fit |
| Window installation | 5 years | The fitting carried out |
We work with our own crews rather than passing the job to a middleman, so the people doing the work are the ones answering for it. Every repair, glass swap and installation is logged against the team that handled it, which means a claim goes straight back to the fitter on site. With a middleman the warranty often travels through a third party, and that is exactly where claims tend to stall — the seller points to the installer, the installer points back, and weeks pass. On our side there is no handoff to argue about, and the parts we fit are the parts we source, so a fault traced to a replaced seal or hinge is handled under the same term as the task itself. Ask any contractor to name the crew that will sign off the job before you book.
Before signing off, open and close the sash, check the lock catches, and run a hand along the seal for draughts. Test the handle through a full turn and confirm the sash sits flush against the frame with no gap at the corners. Look at the seal line where the sash meets the frame — a strip that is pinched or sitting proud will let cold air through within weeks. A unit that closes smoothly on the day but needs force a week later usually signals an adjustment that was not finished, so note anything that feels stiff while the fitter is still there. Catching it on the spot is simpler than booking a second visit for the same fault.
While a technician is already on site, it makes sense to close related jobs in the same visit. Here is what we do with insect screens, window security and the extras that pair naturally with a repair.
We repair insect screens and replace their fixings, and when the frame is bent we make a fresh one to size, with a framed unit ready in 10 to 15 minutes. A pleated version takes 40 to 60 minutes, since the cord and tension are set by hand. Fasteners are chosen to match the window profile and the floor: Z-brackets, plungers or magnets, and we swap a worn set without touching the aluminium itself. Where the mesh is torn but the surround is sound, re-meshing costs less than a full replacement, and we paint the surround any colour to match your windows. A screen that keeps popping out usually needs replacement brackets rather than a whole frame — check the fasteners before ordering a spare unit.
We fit window locks, restrictors and protective grilles so a window opens only as far as you allow. On a tilt-and-turn sash, a cable or folding restrictor limits the gap to a set distance while still letting air through, and a key lock stops the handle turning at all. Grilles are measured to the reveal and fixed to the wall rather than the sash, so the window keeps its full swing. We check the surround before drilling: a loose fixing point will not hold a restrictor under load, and where the profile is thin we reinforce it first.
| Mesh | Best for | Feature |
|---|---|---|
| Standard fibreglass | General use | Fire-resistant, tolerates temperature swings |
| Ultravue | Small or shaded rooms | 25% more light and air |
| Pet Screen | Homes with cats and dogs | Vinyl threads resist a small animal's weight |
| Anti-dust | Street-facing windows | Finer weave holds back dust |
| Poll-Tex | Allergy season | 0.25×1 mm cell traps pollen |
The decisions above come down to a handful of checks: what the fault actually is, whether the frame is sound, and what the contractor puts in writing before work starts.
Window repair, adjustment, winter repairs, technician visits
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionIn cold, the seal contracts and loses elasticity, so gaps become noticeable. In summer the rubber is softer and fits tighter, so the issue is more often a worn seal than the sash itself.
Besides adjusting the sash, the technician lubricates the hardware, replaces a worn seal, and installs new handles or hinges if needed. The exact scope depends on the window's condition and is determined after inspection.
Yes, adjustment is possible even in freezing weather: the hardware is not afraid of cold, the main thing is not to leave the sash open for long. The technician will work carefully and check the seal immediately.
We work without days off, so you can leave a request any day. The technician will agree on a convenient visit time and come with tools and necessary parts.
Yes, we also visit private houses: we repair plastic, wooden, and aluminum windows on any floor. The technician arrives with tools and basic spare parts, and agrees on the scope of work on site.
No, most window repair work is done without removing the frame: adjusting sashes, replacing seal, handles, and double glazing. Removal is only needed for serious profile damage.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp