Technician holding a white window handle with a screwdriver in a children's room
from 750 ₸ per linear metre of sealThe technician will adjust the compression, lubricate the mechanisms and check the drainage, and you pay after the work is done.Calculate

Window Maintenance in Kostanay

Cam adjustment · Season

Winter mode

Before the cold weather we increase the sash compression so the wind doesn't blow through the gap. Seasonal adjustment — from 3 000 ₸ per window.

A hand turns the sash eccentric with a hex key, switching the window to winter mode
GoogleYandex MapsZoon

5,097 reviews on review sites

What window maintenance in Kostanay includes

Preventive care that keeps sashes tightly compressed, handles moving freely, and the rubber seal surviving frost without cracks.

What it consists of

The technician checks every sash: how it hangs on the hinges, where the compression is weaker, whether the handle is loose. Then they switch the cams to the right seasonal mode and tighten anything that has come loose.

The second part is care: we clean the hardware of dust and old grease, apply fresh lubricant, treat the seal with silicone and clear the drainage holes at the bottom of the frame so water drains outside.

A technician wiping the window frame by the handle in a kitchen
from 3 000 ₸

seasonal adjustment of one window

from 6 600 ₸

servicing of all windows in an apartment

1 year

warranty on work and replaced parts

Work
AdjustmentLubricationSealDrainageHandles

How seasonal window care is performed in Kostanay

Four reasons why people in Kostanay most often call a technician before winter and after it.

Serviced window in a study, one handle on the sash
  • 01The window is still in summer mode

    We set the cams to the reinforced pressure position, and the cold wind stops blowing across the windowsill.

  • 02Hardware left without lubrication for years

    We clean dirt from the locking plates, lubricate the mechanisms, and the handle turns without squeaking.

  • 03Time to go through all the windows

    In one visit we inspect every sash in the apartment and do everything needed according to a single list.

  • 04The rubber seal has hardened

    We clean and treat the seal with silicone; if it is torn, we offer a replacement at a separate price.

Types of window care work in Kostanay

You can order a single operation or put together a set for your windows: the technician will say what is really needed and what can wait.

Seasonal mode

per window

Technician holds an L-shaped steel hex key used to adjust the window hinge

We switch the cams to winter or summer mode and check the pressure around the entire perimeter of the sash.

from 3 000 ₸

Hardware lubrication

per sash

A technician holds a small brush with silicone lubricant for cleaning the handle and hinge

We clean the mechanism from dust and old grease, apply new lubricant, and the movement becomes smooth.

from 1 250 ₸

Rubber seal care

per linear metre

Hands lubricate the window's rubber seal with silicone using a cloth

We wipe and treat the seal with silicone to keep it elastic.

from 750 ₸

Against draughts

per sash

A hand checks with a strip of paper whether air blows from under the window sash

We find where the cold is coming in and adjust the sash so that the gap disappears.

from 3 500 ₸

New handle

per piece

A technician holds a new white handle for a plastic window

We replace a loose or broken handle with a new one, matching it to your profile.

from 2 750 ₸

Window maintenance prices in Kostanay

The total depends on the number of sashes and the selected works; the technician gives the sum before starting.

Type of workPrice
Seasonal maintenance (winter/summer)switching the cams to the right modefrom 3 000₸ per window
Basic sash adjustment during servicinghinges and compressionfrom 3 000₸ per sash
Cleaning and lubricating the hardwaredust and old greasefrom 1 250₸ per sash
Cleaning and lubricating the sealsilicone carefrom 750₸ per linear metre
Eliminating draughtsfinding the gap and adjustingfrom 3 500₸ per sash
Balcony door adjustmentsagging, rubbing against the thresholdfrom 6 000₸ per item
Window handle replacementloose or broken mechanismfrom 2 750₸ per item
Winter (slotted) vent installationmicro-ventilationfrom 7 600₸ per item
Comprehensive window servicingall components in one visitfrom 10 000₸ per window
Apartment window servicinginspection and care for all windowsfrom 6 600₸ per apartment
Thermal imaging window checkfinding cold spotsfrom 9 000₸ per job
Call-out and inspection by a technician (without ordering a repair)diagnostics without repairfrom 3 600₸ per job

The price is fixed in the order after measurementMeasurement and consultation are freePayment after work: cash, card, Kaspi

Book a technician

Why customers order window care from us in Kostanay

Briefly about what you can count on when you invite us to your windows.

Repair warranty1 year

for the completed works and the components we replaced

Reply in WhatsApp5 minutes

that is how long you usually wait for a reply to a photo of the window and a question

Paymentafter

the work, when you have checked the sashes: cash, card or Kaspi

Pricein the order

we fix the sum after measurement, and it does not grow during the work

Profilesany

we replace seals in KBE, Rehau, VEKA, Provedal and other windows

Scheduleno days off

we come on both Saturday and Sunday

Experiencesince 2012

we work across Kazakhstan

Screensour own

we can also install or remove a mosquito screen at the same time

How window maintenance is carried out in Kostanay

From a message to checking the sashes together with you.

  1. A hand holds a smartphone with a dark screen next to a white PVC window
    01reply in 5 minutes

    You write to us

    You send a photo of the window via WhatsApp and a few words about what is bothering you: draught, squeaking, not closing.

  2. A tape measure measures the window opening, a hand holds the measuring tape by a white window
    02at a convenient time

    Inspection

    The technician checks the sashes, hinges, handles and rubber seal and gives a list of works with prices before starting.

  3. Hex keys and lubricant on a table
    03in one visit

    Works

    Adjusts the pressure, lubricates the hardware, treats the seal and clears the drainage according to the agreed list.

  4. A serviced white window in a dining room, a table in the foreground
    04in your presence

    Check

    You open and close each sash yourself, and only after that you pay for the work in a convenient way.

Good to know

Window Maintenance in Kostanay with a Free Measuring Visit

We handle window maintenance in Kostanay with our own fitters, not through an agency. We repair and adjust plastic windows, replace seals and glass units, insulate frames and fit restrictors, locks and grilles. A free measuring visit comes first, the price is fixed in the order after it, and you pay only once the work is done.

What Window Maintenance Covers and How to Pick the Right Service

Window maintenance in Kostanay is not one service but a set of jobs, and which ones your unit needs depends on the symptom you see, not on a fixed package. Below is what a visit can include.

The Five Jobs a Maintenance Visit Can Cover

  • Adjustment: re-setting a sash on its axes so it closes evenly without dragging or leaving a gap.
  • Hardware repair: replacing worn handles, hinges, tilt-sliders and locking points, or fitting new fasteners.
  • Seal replacement: swapping a compressed or torn gasket so the sash holds air again and stops whistling.
  • Glass unit replacement: fitting a new sealed unit when the glass has fogged, cracked or lost its inner seal.
  • Insulation: closing the gaps around the frame so the whole unit holds heat, not just the pane.

Adjustment, Repair or Replacement and How to Choose

Adjustment fixes a sash that still seals, repair replaces a worn part, and replacement only makes sense when the frame or glass unit itself has failed. A sash that rubs against the frame but still presses evenly on the gasket is an adjustment job — the fitter re-sets it on its axes and the sash closes cleanly again. A handle that turns loosely or a gasket flattened to a thin strip is a repair: the part comes out and a new one goes in. Replacement enters only when the frame has twisted out of square, the profile is cracked, or the pane has fogged between the layers. We adjust sashes on their axes and replace hardware and seals as separate jobs. A window that is still square and holds a seal is almost never worth replacing; the money usually goes further on hardware and seals.

How Often a Unit Needs a Maintenance Visit

A window that is adjusted and sealed properly usually needs a check once a year, and the best moment is just before the heating season starts. In that single visit a fitter re-sets the sashes on their axes, checks the gasket along the whole perimeter and closes the gaps around the frame, so the frame holds heat through the coldest weeks. A unit that has never been adjusted since installation often needs two visits the first time — one to correct what has drifted and one a season later to confirm it held. The visit is worth timing to the season rather than to a calendar reminder: a sash set tight for winter needs a lighter setting again in spring, and leaving it on the winter setting through summer presses the seal flat faster than any other single cause.

Reading the Symptoms Before You Call Anyone for Window Maintenance

Most complaints about draughts and sticking sashes point to a specific cause, and naming it before anyone visits saves time and money. Here are the two patterns we hear about most and what each one usually means.

Why a Closed Window Still Lets in Cold Air

A draught on a closed unit almost always comes from a compressed seal, a dropped alignment or a lock that no longer pulls the leaf tight against the frame. Old rubber flattens and loses its spring, so the gap widens by a millimetre or two — enough for cold air to pass along the whole perimeter. A lock that has lost tension leaves one side loose even when the handle is down. We replace seals on units of any make, including KBE, Rehau, VEKA and Provedal profiles, so the fix rarely depends on the original brand. Test with a sheet of paper trapped in the closed leaf: if it slides out with no resistance at one spot, the problem is local and cheap to fix.

A Sash That Sags, Catches or Will Not Close

A leaf that catches the frame has usually dropped on its hinges, and our fitter corrects it by adjusting the sash on both axes rather than forcing the handle. Hinges carry the full weight of the moving part, and over years the lower side sinks until it scrapes the sill or the surround. Turning the adjustment screws on the hinge plate lifts that side back and restores the gap on all four edges. Forcing the handle instead bends the locking pins, and then the whole hardware set needs replacing. After adjustment the handle should turn with light pressure and the leaf should sit evenly on all four sides — check that before the fitter leaves, and ask him to show you the two screws he turned so you can repeat it yourself next season.

Seals and Hardware Matched to Your Profile for Window Maintenance

A seal or a hinge is chosen to fit a specific frame profile, not picked off a shelf by eye. Profiles differ in groove depth and width, so no single universal strip works everywhere.

Which Seal Fits KBE, Rehau, VEKA and Provedal

Gasket selection points by frame profile
ProfileWhat the fitter checks before choosing a gasket
KBEGroove depth and the width of the sash rebate
RehauSeat geometry and corner joint tightness
VEKAFrame groove shape and the gap at the sash edge
ProvedalAluminium profile width and drain channel position

When a Seal Is Worn and How Often to Replace It

  • No rebound: press the strip with a finger and it stays dented instead of returning to shape.
  • Hard ribbon: the rubber has gone stiff and cracks when you bend it.
  • Lifted corners: the strip has separated from the frame where the sash meets the sill.
  • Draft at the edge: cold air reaches your hand along the sash line even when the handle is locked.

How a Visit Runs from First Message to Final Check

The route from your first message to a checked, sealed result is short: a free measuring call, a locked-in quote, the job itself and a final tightness test before we leave.

Free Measuring, Fixed Price and Payment After the Work

The measurer arrives at a time that suits you, takes the sizes and helps choose the parts, and the figure is fixed in the order once that call is done — you settle up when the job is finished, by cash, card or Kaspi. We answer on WhatsApp within five minutes and stay open seven days a week, so a weekend request works the same as a weekday one. The specialist checks the profile, the floor level and the existing fixings, then offers the mesh and fasteners that fit — Z-brackets, plungers or magnets. Because the amount is locked after measuring, a fitter who finds a second worn hinge on site cannot quietly add it to the bill without agreeing it with you first.

Timing, Same-Day Glass Units and the Warranty You Get

A standard repair or adjustment is done during the call, an urgent glass unit can be made and fitted within one day at a surcharge, and every repair carries a one-year warranty on labour and replaced parts. Fitting a framed screen made to your size takes 10–15 minutes, while a pleated screen runs 40–60 minutes. A glass unit replacement carries a three-year warranty, which is longer than the repair cover because the unit itself is a sealed factory part rather than a fitted component. Installation, when a job turns into a full project, is covered for five years. We confirm the slot in the same WhatsApp thread, and the fitter runs a tightness check on the seals and hardware before signing the work off.

Winter Prep and Window Safety for Families

Winter in this region tests both the seal and the hardware, while households with small children and pets need a separate layer of protection on top of routine upkeep.

Getting the Units Ready for a Kostanay Winter

Winter prep means checking the seals, adjusting the sash so it presses evenly against the frame and insulating where the frame meets the wall, and this work can be done in cold weather without removing the unit. We start with the gasket, because a flattened seal lets cold air through long before the glass itself is at fault, then move to the hardware and reset the moving panel. Insulating the perimeter joint matters as much as the seal on older blocks, where foam and plaster have settled over the years. Setting the panel tighter for winter and looser for summer is normal practice, not a sign of a faulty unit — the hardware has a seasonal setting for exactly this. On our visits we mark the summer position, so the household can switch back in spring without guessing.

Restrictors, Locks and Grilles for Children and Pets

  • Opening restrictor: limits the moving panel to a ventilation gap and mounts on the surround or the hinge arm.
  • Window lock: holds the handle fixed with a key, useful on ground-floor and balcony units.
  • Protective grille: a fixed barrier for openings onto a courtyard or above a low sill.
  • Fixing set: Z-brackets, pins or magnets, matched to the profile and the floor by the fitter.
  • Ventilation stop: the practical middle ground between a locked unit and one open wide enough for a child to pass.

Window maintenance for seasonal tasks

A visit works best when you arrive prepared: clear symptoms, a few measurements and the right questions about materials and hardware save time for everyone involved.

  • Describe the fault precisely: note which sash sticks, where cold air enters and whether the handle turns loosely — a specific symptom shortens diagnosis on site.
  • Measure the opening yourself: width and height of the frame, not the glass, in millimetres; the measurer confirms the figures and picks the fixings for your profile and floor.
  • List the units and doors in one message: plastic, wooden or aluminium units, loggia and balcony openings, and any insect screens you want repaired or refitted.
  • Ask what the visit includes: free measuring, a fixed price set in the order afterwards and payment once the work is finished.
  • Keep the old parts: worn seals, handles and fasteners show the technician what failed and help match replacements to your profile.

Questions about window maintenance in Kostanay

Adjustment, seal, airtightness, warranty, seasonality

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can a technician adjust the sash and replace the seal in one visit?

Yes, a technician can do several jobs in one visit: tighten the sash, replace the seal and lubricate the mechanisms. The exact list depends on the window's condition and is agreed on site.

02Can the seal be replaced on a KBE or Rehau window in Kostanay?

Yes, we install new seals on windows of various brands, including KBE, Rehau, VEKA and Provedal. The technician arrives with samples, selects the right profile and replaces it around the sash perimeter.

03How can I check myself that the window closes tightly after servicing?

Close the sash and try to slip a sheet of paper between it and the frame around the perimeter — it should be gripped with resistance. Another sign: no draught at the handle or corners, and no whistling in the wind.

04What if during window servicing the technician finds a crack in the double glazing?

They will show it to you and offer to replace the double glazing — if urgent, this is done within a day. If the crack is inside the chamber, repairing the sealant won't help; replacement is needed.

05Is window servicing done in winter or should I wait for warmer weather?

It is done in winter too: adjustment, lubrication and seal replacement are possible at sub-zero temperatures if the window is not frozen. The technician works carefully to avoid damaging the profile in the cold.

06Why does the window close more tightly than before after servicing?

Most likely the sash was overtightened or the new seal hasn't settled yet. Tell the technician — the pressure is adjusted to the seal's density, and the movement becomes smoother.

07What is included in window servicing if the windows are still under the developer's warranty?

Servicing does not void the developer's warranty: we perform adjustment, lubrication and cleaning without interfering with the structure. If a defect is recognized as warranty-related, it's better to contact the developer first, while maintenance can be done in parallel.

Reviews of window maintenance in Kostanay

5,0based on 97 reviews on platforms
All reviews