Sash
Rubber and hinge adjustment remove the gap around the sash perimeter. From 1 000 ₸ per linear m.


After the work there's no draught by the window, the glass is dry, and there are no stains on the reveal. All without replacing the window.
The master finds where the window loses heat and closes these spots: replaces rubber, adjusts hinges and pressure, seals the seam around the frame, insulates the reveal and window sill. The window stays yours, only its tightness changes.
The wind from the foothills of Zhetysu and frosty nights in Taldykorgan quickly cool apartments through gaps. After insulation the radiators cope, and the heater by the window can be removed.

window in one visit: rubber, pressure, seams
warranty on repair and parts
payment when you've checked the window
What apartment and house owners see.

On a windy night the sash whistles — the rubber doesn't press.
The foam by the frame darkens, the wall nearby is cold.
A cold reveal collects moisture, mold stains appear.
Cold comes from under the window sill to the floor.
Usually two or three are needed, the exact list will be given by the master.
whistling and draught

Fresh rubber plus tightened hinges and cams.
dark foam

Liquid plastic on the room side protects the seam.
stains on reveal

The insulation layer hides under the finishing.
icy floor

We fill the void under the board, seal the joint.
street side

Sealant outside keeps rain and snow out of the foam.
The amount depends on the set of works, the master will name it during the inspection.
| Type of work | Price |
|---|---|
| Window in one visitmain package | from 3 800₸ per window |
| Sealrubber replacement | from 1 000₸ per linear m |
| Draught from sashwe fix | from 3 500₸ per sash |
| Liquid plasticseam inside | from 1 500₸ per linear m |
| Sealant outsidefacade seam | from 2 000₸ per linear m |
| Revealwarm, with finishing | from 19 900₸ per linear m |
| Window sillfoam and seam | from 15 000₸ per job |
| Wooden windowsSwedish technology | from 4 200₸ per linear m |
| Micro-liftextra pressure | from 1 700₸ per pc |
| Between framesone more contour | from 2 800₸ per window |
| Thermal cameraleak detection | from 9 000₸ per job |
| Balconyinside | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Book a technicianWhat sets us apart.
we stand behind our repairs and parts
we match seals to KBE, Rehau, VEKA, Provedal
after the inspection the price is written into the order
cash, card or Kaspi — your choice
our average response time
we work without days off
this is when we take requests
we work across Kazakhstan
Four steps.

Tell us what's wrong with the window: whistling, a damp seam, stains on the reveal or cold from the floor, and send a photo.

The technician checks the sashes, seams, reveals and windowsill and gives you a price.

We replace the seals, adjust the hinges and closing pressure, seal the seams and foam the windowsill.

We check the window for draughts together with you, then you pay.
Good to know
We handle window insulation in Taldykorgan with our own fitters, not through middlemen. We start with a free measuring visit, find where the draught actually enters, then replace the seal, adjust the sash or fit a new glass unit as the window needs. Payment comes after the work.
A closed window that still feels cold shows the weak point. Before ordering anything, we trace the draught to its source instead of guessing.
Our fitter checks the gasket, leaf pressure, glass edges and perimeter in that order, so the fix matches the real cause. We press the rubber at several points to see whether it still springs back, then test how firmly the locking cams pull the leaf against the profile. Next comes the glass unit, inspected for fogging between the panes and for a chill edge on the inner surface. The perimeter is last, because foam and sealant failures show up as a cold line along the slopes rather than at the opening. Measuring and consultation are free, and the measurer arrives at a convenient time with sizes, mesh and fixings in mind.
The seal is the cheapest window part and the first to fail. We match a new one to your existing sash, regardless of brand.
We replace the gasket in units of any manufacturer, including KBE, Rehau, VEKA and Provedal, using a strip cut to your own sash rather than a universal cord. The rubber has to sit in the groove the frame was milled for, so we note the model name and the channel depth before cutting anything. On Rehau or VEKA sashes that channel is narrow and deep; on Provedal aluminium units the geometry is flatter, and a soft universal cord simply rolls out of it after a few weeks. A strip that is too thick stops the sash closing flush and can crack the corner over a season.
Not every cold window needs the same work. The symptom you feel decides whether adjustment, a new seal or a glass unit is the honest answer.
| What you notice | Likely cause | Work that fixes it |
|---|---|---|
| Draught along the opening edge | Worn seal | Seal replacement |
| Sash loose or hard to close | Sash pressure | Adjustment |
| Cold across the whole pane | Glass unit | Glass unit replacement |
| Cold strip around the frame | Mounting joint | Perimeter and slope work |
If the pane mists between the layers or stays cold across its whole surface, we replace the glass unit, and an urgent one can be made and fitted within a day. An even chill across the whole surface means the sealed chamber has lost its gas fill. We measure the unit on site, order it to the exact millimetre and swap it without touching your frame or slopes. Replacement glass units carry a three-year warranty, and urgent production is available for a surcharge on the unit itself. A glass unit swap keeps your existing frame and slopes untouched, so it is often the faster route to a warm room.
Autumn is the right moment to check your windows while the cold is mild and a fitter can work without rushing; a short checklist covers most winter needs.
Winter adjustment pulls the leaf tighter against its frame, so the seal presses evenly and the draught along the opening edge stops. We set the eccentrics, check the hinges for play, test the handle travel and run a hand along the closing edge on the windward side. Proper window insulation in Taldykorgan starts with this even compression, so the sash holds its fit through the coldest weeks. The aim is even compression around the whole perimeter, not a single hard-clamped corner. Over-tightening wears the mechanism out faster, so pressure is set to the seal, not the screw's maximum. A leaf set this way keeps its fit until spring.
Plastic units get most of the attention, but timber and aluminium lose heat in their own way. The perimeter matters just as much as the sash itself.
We work on plastic, wooden and aluminium frames, and a timber unit can often be sealed and adjusted without being torn out. On wood we plane a warped casement, replace worn brush or rubber seals along the rebate, and refit the hardware so the leaf closes tight. On aluminium the weak points are the thermal break and the glazing gasket: a hardened gasket pulls away from the glass. Both materials take new glass units and fresh perimeter sealing, so the frame keeps its character while the draught goes. Timber moves with the seasons, so a seal set in a dry spell can open a gap again in the damp.
A cold strip around the whole opening points to the seam behind the slopes, not to the seal or the glass. That seam sits between the frame and the wall, where foam, vapour barrier and plaster meet. Foam alone does not stop a perimeter draught; the gap needs a vapour-tight layer and a finished slope to keep the chill out. When the slope pulls away, the edge opens, rain gets behind it, and the foam soaks up water and stops insulating. Residents of Taldykorgan feel this first on the north wall, where the seam stays coldest longest. Re-sealing it and refitting the slopes fixes the actual path heat takes.
The process itself is short and predictable. A free visit sets the plan, the fitters do the job, and you pay once it is finished.
Measuring and consultation are free, and the measurer comes at a time that suits you, takes the sizes and helps choose the seal, the fixings and the scope of the job. Insulation in Taldykorgan begins with that appointment rather than a phone guess: the fitter checks the profile, the sash and the mounting joint, then writes down the plan for the flat. The price is fixed in the order after measuring, so the figure you agree on the spot is the one you pay, with no add-ons later. Ask the measurer to show where the draught enters — that decides whether you need a seal, an adjustment or new glazing.
The order of work matters more than the amount of material used, because each weak point needs its own fix. A short checklist keeps the visit focused and the result predictable.
Signs, sealing, comprehensive insulation, warranty
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionIf cold air comes in around the sash perimeter, replacing the seal and adjusting the window is often enough. If the double glazing fogs up from the inside or the frame is cracked, that's already repair or replacement, and a technician decides after inspection.
You shouldn't apply sealant to the frame and sash themselves: it interferes with the hardware and profile ventilation. If the draft comes from the sash, you need a new seal or pressure adjustment, and gaps in the installation seam are sealed from the outside with special materials.
Typically it includes replacing the seal around the sash perimeter, sealing the installation seam from the outside, treating the glazing beads, and insulating the reveals if needed. The technician selects the set of works after inspection, because the cause of cold differs for each window.
Yes, if freezing occurs along the edge of the double glazing or through the glazing bead, replacing these elements eliminates the cold bridge. But the decision is made after inspection: sometimes it's enough to insulate the glazing bead and replace the seal, without touching the double glazing.
Yes, wooden windows are insulated the same way: the seal is replaced, seams are sealed, and if necessary the reveals and windowsill are treated. If the sashes have dried out or sagged, the technician will first say whether insulation will help or the frame is better replaced.
Yes, for window repair we provide a 1-year warranty on work and replaced components. If the window drafts again after insulation, the technician will look into the cause and advise what to do next.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp