Technician holding a new window sash with a double-glazed unit in a bedroom
from 1 300 ₸New glass to measure for your sash, without dismantling the frame and with payment after installation.Calculate

Double Glazing Replacement in Taldykorgan

Country house · Winter

Double-chamber

If the country house is heated in winter, it's better to replace the single-chamber unit with three panes, and the frost will disappear. From 20 000 ₸ per m².

White PVC window in winter, a snowy courtyard outside, a floor lamp and a small table beside it
GoogleYandex MapsZoon

5,097 reviews on review sites

What is double glazing replacement in Taldykorgan

Work for windows where only the glass is damaged. The frame and hardware remain, and you can immediately choose a unit better than the old one.

Key points

The unit is held in the sash by glazing beads and spacers; it can be removed without touching the frame, reveals or windowsill. The master installs a new unit of the same size, returns the glazing beads and adjusts the sash so it closes tightly.

Taldykorgan is surrounded by foothills; winters here can be windy and frosty, and summers are hot. Therefore, for country houses and apartments on the windy side, we recommend a double-chamber unit, and for sunny windows — glass with a coating.

Empty PVC window sash against the wall and removed glazing beads on the floor next to a balcony door
from 12 600 ₸

single-chamber unit per square metre

3 years

warranty on the installed unit

free

measuring and glass selection

Units
Double-chamberSoundproofCoatingSingle-chamberFrosted

How a new unit in the sash is performed in Taldykorgan

Four common reasons for requests from Taldykorgan.

A craftsman inserts a white glazing bead into the sash with a rubber mallet
  • 01Crack in the glass

    A crack from an impact or temperature difference grows over time; it's better to replace such a unit immediately.

  • 02Foggy between the panes

    If there is fog and streaks inside the unit, the sealant is letting moisture in, and the unit cannot be restored.

  • 03Glass is broken

    We will make and install the unit urgently, within one day; a surcharge will be added to the price of the double glazing.

  • 04Cold near the window

    We replace a single-chamber unit with frost on it with a double-chamber one, and the room becomes warmer.

Types of glazing units for Taldykorgan apartments

Five options to choose from during replacement, from simple for a loggia to soundproof.

Double-chamber

country house, bedroom

White PVC window in winter, a snowy courtyard outside, a floor lamp and a small table beside it

Three panes retain heat in a windy winter, and frost does not build up on the glass.

from 20 000 ₸/m²

Soundproof

windows facing the street

White PVC window high above a busy avenue, a bookcase beside it

Different glass thickness dampens street noise better than a standard unit.

from 19 500 ₸/m²

With coating

sunny side

White PVC window in a home office, a desk with a laptop and a lamp in the foreground

Energy-saving glass keeps out heat in summer and retains warmth in winter.

from 15 200 ₸/m²

Single-chamber

loggia, utility room

White PVC window in a dining room, with an oak table and chairs next to it

A lightweight double-glazed unit for unheated spaces.

from 12 600 ₸/m²

For doors

balcony door

Hands install a new glass pane into a balcony door sash

Glass for a PVC door of the required thickness, with hinge adjustment.

from 22 000 ₸/m²

Double glazing replacement prices in Taldykorgan

The final price depends on the glass area and the type of unit; we confirm it after the measuring visit.

Type of workPrice
Double glazing replacement, per m²new unit to measurefrom 19 500₸ per m²
Single-chamber unitloggia and utility roomfrom 12 600₸ per m²
Double-chamber unitcountry house and living roomsfrom 20 000₸ per m²
Energy-saving unitsunny windowsfrom 15 200₸ per m²
Broken glass replacementsingle pane of the unitfrom 8 000₸ per m²
Glass in a plastic doorbalcony exitfrom 22 000₸ per m²
Glass tintingwith filmfrom 5 500₸ per m²
Protective film on glasschildren's room, ground floorfrom 8 000₸ per m²
Additional glazing beadsecure fitfrom 1 300₸ per item
Sash adjustment with removalafter unit replacementfrom 4 000₸ per sash
Master's visit and inspectionwithout repair orderfrom 3 600₸ per job

The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi

Book a measuring visit

Why customers order a new unit in Taldykorgan from us

Order terms in Taldykorgan.

Warranty3 years

on the new unit and installation

Paymentafter

installation: cash, card or Kaspi

Urgent1 day

if the glass is broken, with a surcharge on the unit price

Measuringfree

at a convenient time, with unit selection

Pricein the order

the amount does not change after measuring

Response5 minutes

on WhatsApp to a message and window photo

Openseven days a week

we take requests all week

Experiencesince 2012

we work across Kazakhstan

How double glazing replacement is carried out in Taldykorgan

The process in four steps.

  1. A hand holds a phone with a dark screen by a plastic window for measuring
    01response in 5 minutes

    Message

    Send a photo of the window on WhatsApp and describe the issue: a crack, fog, cold or noise.

  2. A tape measure measures the sash opening of a white plastic window, only hands are visible
    02free

    Measuring

    The surveyor measures the glass, checks the profile and suggests a suitable unit.

  3. Hands assemble a glass unit from glass panes and an aluminum frame on a workbench
    03urgent — one day

    Manufacturing

    The unit is made to the size of your sash; if the window is broken, we will make and install it within a day with a surcharge.

  4. A new glass unit is installed in a white plastic window sash, clean glass
    04while you watch

    Installation

    The technician replaces the unit, fits the glazing beads, adjusts the sash, and we take payment after you check the work.

Good to know

Double Glazing Replacement in Taldykorgan

We handle double glazing replacement in Taldykorgan as a direct contractor with our own fitters. We measure for free, fix the price in the order after measuring, and you pay only after installation by cash, card or Kaspi. Every replacement unit carries a 3-year warranty, and urgent jobs can be made and fitted within one day.

Spotting a finished sealed unit and one with life left for double glazing replacement

Most calls start the same way — the window is fogging up. Behind that one symptom sit three different causes, and only one of them calls for a new sealed unit.

Fog between the panes and what it actually means

Condensation trapped between the panes means the sealed unit has lost its hermetic seal, and no amount of wiping will fix it. The glass itself is usually intact; what failed is the perimeter bond between the spacer and both panes, so moisture from the air migrates into the cavity and settles there. Once that happens, the assembly cannot be dried out or re-sealed on site — it is replaced as a whole, sized to the existing bead. Fog that appears on the room-side surface tells a different story: that is a ventilation and humidity issue, not a failure inside the panel. Before ordering new glass, check the gasket and hardware — a worn one lets warm air reach the cold pane and condenses there.

Three faults that look the same but need different work

Three complaints and the work each one needs
What you noticeLikely causeWhat we do
Fog or moisture between the panesBroken seal inside the unitReplace the sealed unit
Draught along the sash edgeWorn gasket or loose hardwareReplace the gasket or adjust the hardware
Cracked or chipped glassImpact damageUrgent unit replacement

Choosing a double glazing replacement unit for a Taldykorgan winter and your room

The city swings between a hot summer and a properly frosty winter, so the number of chambers and the type of glass decide whether your window stays clear or streams with water by February.

Single chamber or double chamber for a cold snap

A two-chamber unit holds heat noticeably better in a cold snap, while a single-chamber build is enough for a mild room or a balcony. The two-chamber build stacks three panes and two sealed air gaps, which slows heat loss through the whole surface instead of one thin barrier. A single-chamber unit carries two panes and one gap, so it suits a glazed loggia, a summer kitchen or a hallway that never drops far below freezing. The width of that gap matters as much as the count: a 16 mm spacer behaves differently from a 10 mm one at minus twenty. The wider the gap between panes, the more the unit relies on the frame and seal to keep that gain — a good unit in a tired frame still underperforms.

Where an energy-saving coating earns its place

We suggest an energy-saving coating for rooms that face the street or sit above a cold basement, where the inner pane is the first to fog. The low-emissive layer reflects warmth back into the room rather than letting it escape through the glass, which lifts the temperature of that inner surface by a couple of degrees and pushes condensation below the dew point. On the north wall of a flat or above an unheated garage, that difference shows up as a dry sill instead of a wet one. Our measurer checks exactly this during the free measuring and consultation, noting which rooms face the weather and which stay sheltered. The coating works on the room-side pane, so it pays off most on the coldest wall of the flat, not on every window at once.

How the double glazing replacement runs from measuring to handover

The job runs in four steps, and the frame with its profile stays where it is — only the sealed glass changes, plus the retaining strip and the seal if they need it.

The measuring visit and why the size is measured on the bead

Our measurer comes at a time that suits you, takes the size from the glazing bead rather than the outer frame, and the measuring visit costs nothing. He checks the profile, the depth of the rebate and the state of the seal, then helps you pick the glass and the strip that will sit back into that same opening. The bead is the narrow strip holding the pane in place, so the number he writes down is the one the workshop builds to. A replacement cut to the frame size instead of the bead will not seat properly and can crack on the first cold night. This is how the double glazing replacement taldykorgan customers order stays accurate from the first visit to the finished window.

What the fitting day looks like and what to clear away

  • Clear the sill: move plants, ornaments and curtains away from the window before the fitters arrive.
  • Old pane out: the fitters lift out the failed glass and check the strip and seal underneath.
  • New pane in: the replacement is seated, the strip refitted and the seal checked for a tight fit.
  • Quick clean: glass and frame are wiped down so you can inspect the result straight away.
  • Handover: you check the window with the fitter before the job is signed off.

Urgent breakage, awkward windows and other non-standard jobs

A cracked pane, a timber frame or a top-floor flat changes the timing and the order of work rather than the service itself. Knowing what each case needs saves a second visit.

Same-day replacement when glass is broken

We can make and fit a replacement pane within one day when the glass is broken, with a surcharge added to the price. The sealed unit is assembled to the measured size, the old one is taken out and the new set on fresh supports and sealed along the bead. Send a photo and rough dimensions on WhatsApp first thing in the morning — we reply within five minutes and start cutting as soon as the size is confirmed. A same-day job depends on that early confirmation, so the earlier the photo arrives, the more of the day is left for assembly and fitting. Board up or tape a shattered pane before we come if the gap faces the street.

Wooden, aluminium and upper-floor windows

We fit glazing into plastic, wooden and aluminium frames, and the method is chosen on site to suit the frame and the floor. On timber the old bead often comes away with the glass and is refitted by hand, which adds time compared with a standard plastic window. Aluminium frames use their own glazing strips, and the fitter checks the drainage slots before the new set goes in. On upper floors the panel is carried in through the stairwell and lifted into the opening from inside, so nothing hangs over the facade. Timber frames often need the bead refitted by hand, so allow a little more time than for a standard plastic window — book such a job for the morning and keep the afternoon free.

Warranty, payment and what the 3-year cover includes

Warranty terms and the payment order are where a direct contractor differs from an aggregator, where responsibility is split between the platform and the fitter who turns up. Here is what our cover includes and how settlement works.

What the 3-year warranty covers and what it does not

Every replacement we fit carries a 3-year warranty covering fogging between the panes, seal failure and delamination of the glass unit itself. The cover runs from the day of handover and applies to the assembly as a whole, not to a single pane of glass. A crack caused by impact, a broken frame from a slammed sash, or damage left by another contractor on the same window falls outside the cover. Keep the handover checklist signed on the fitting day — it records the condition of the glazing and the frame at acceptance. In our practice most warranty questions come down to whether the fault sits inside the sealed cavity or outside it, and that record settles the point quickly.

How long a unit lasts and when to replace just the glass

A well-made sealed assembly typically serves for many years, and when only one pane is cracked the whole thing is still replaced as a single factory-sealed item. It is built from two or more panes held apart by a spacer bar and closed at the plant, so the cavity and the desiccant inside it work as one system. Swapping a single pane on site breaks that closure, and moisture reaches the desiccant within a season — the fog returns and the job must be redone. The same logic applies when the seal has failed but the glazing is intact: the assembly is what ages. Judge the unit by fog, condensation inside the cavity and a visible film on the inner surface, not by the age of the window.

Paying after installation and reaching us quickly

  • Price fixed after measuring: the figure in your order does not change once the measurer has been.
  • Pay after fitting: settle by cash, card or Kaspi once the work is checked.
  • WhatsApp replies: we answer within 5 minutes, seven days a week.
  • Direct contractor: our own fitters do the work, so there is one point of contact.

How to avoid mistakes with double glazing replacement

Five points decide whether a replacement goes smoothly: correct diagnosis, the right number of chambers, an accurate measurement, a glazed panel swapped whole, and warranty terms read before signing.

  • Fog between panes: moisture locked inside means the seal has failed, while condensation on the room side usually points to a ventilation issue.
  • Chamber count and coating: a two-chamber build holds heat better in a cold snap, and an energy-saving coating pays off most on the coldest wall.
  • Measurement point: the size is taken from the glazing bead, not the outer frame, which is why a proper measuring visit matters.
  • Broken glass: a cracked pane is replaced as a complete sealed assembly, and urgent jobs can be made and fitted within a day.
  • Paperwork: check the warranty terms and the handover sheet before signing off, since impact damage sits outside the cover.

Questions about double glazing replacement in Taldykorgan

Double glazing replacement, fitting, sizes, warranty, choosing a double glazing unit

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can a double glazing unit be replaced in a plastic window without removing the frame from the wall?

Yes, when replacing a double glazing unit, the frame and sash are left untouched: the technician carefully removes the glazing bead, takes out the old unit and installs a new one. The frame stays in place, so the work is quick and clean.

02What happens if a double glazing unit is ordered 5 mm smaller or larger than needed?

If the unit is smaller, it will rattle and let in draughts, and if it is larger, it will not fit into the sash or will damage the glazing bead. That is why the size is taken by the surveyor, who is also responsible for accuracy.

03Is it possible to replace a double glazing unit on the 9th floor without scaffolding or aerial platforms?

Yes, in most cases double glazing replacement is done from inside the room and no special equipment is needed. If the window is fixed or access is difficult, the technician will assess the feasibility of the work on site.

04If a double glazing unit fogs up from the inside, is it a warranty case or does it need replacing?

Fogging between the panes indicates a seal failure, and such a unit is replaced entirely. If it is under warranty, the case is recognised as a warranty one after inspection.

05How does replacing a double glazing unit differ from replacing the whole window?

Replacing a double glazing unit means only a new unit in the existing frame, while replacing a window means a complete change of the structure. If the profile and hardware are intact, it is enough to replace the double glazing unit rather than the whole window.

06Can an energy-saving or sound-insulating double glazing unit be installed instead of the old one?

Yes, instead of a standard unit, an energy-saving or sound-insulating one can be installed if the profile and sash allow it. The surveyor will suggest a suitable option after inspecting the window.

Reviews of double glazing replacement in Taldykorgan

5,0based on 97 reviews on platforms
All reviews