Single-sash
Compact window for kitchen or bedroom: manufacture and installation from 42 500 ₸ per window, free measuring visit.


Single-sash
Compact window for kitchen or bedroom: manufacture and installation from 42 500 ₸ per window, free measuring visit.

Double-sash
Window with two sashes for living room and bedroom: manufacture and installation from 65 500 ₸ per window.

Balcony unit
Window and door as a set for access to balcony or loggia: from 95 500 ₸ per set with installation.

Bay window
Installation of bay window in private house: structure with fitting from 60 000 ₸ per m², free measuring visit.

Noise reduction
Noise-reducing windows for home by the road or office: structure with fitting from 60 000 ₸ per m².

5,097 reviews on review sites
Removal of old frame, installation of new one to GOST, window sill, drip sill and reveals — the work that makes the window ready to use.
Window replacement is not just fitting a new frame. The structure is installed in the opening with vapour and waterproofing of the seam, then the window sill, external drip sill are fitted and reveals are finished so the opening is protected from draughts and moisture.
How window replacement in a panel building differs from a brick one — the opening, fixing, reveals. In a panel building the opening is usually even but with thin outer walls, so it is important to choose the right fixings and insulate the reveals. In a brick building the opening may have unevenness requiring additional preparation, and fixings are chosen taking into account the density of the masonry.

warranty on window fitting
measuring visit and surveyor consultation
price is fixed in the order
Four steps from preparing the opening to sealing the seam; if the seam freezes after someone else's installation, reinstallation to GOST is carried out.

The old frame and sashes are removed, the opening is cleaned of fixing and foam residues, geometry is checked.
The frame is levelled and fixed in the opening so the sashes move freely, without distortion.
The seam is filled with mounting foam, covered outside and inside with vapour and waterproofing to prevent draughts.
If the seam freezes after someone else's installation, the structure is re-installed to GOST with insulation restored.
Five options for different needs: kitchen, living room, balcony, private house and an office by the road.
Kitchen, bedroom

A compact window for small openings: made and installed turnkey.
Living room, bedroom

A two-leaf window for rooms with a large opening and good light.
Balcony, loggia

A window and door set for access to a balcony or loggia, with installation.
Private house

A bay window structure with installation: suitable for houses with a projecting opening.
Street, office

A window for a house by the road or an office in a business center: structure with installation.
The table shows works and structures for this page with 'from' prices; the exact cost is fixed after measuring.
| Type of work | Price |
|---|---|
| Dismantling of old windowremoving frame and sashes | from 1 800₸ per m² |
| Installation of PVC windowfitting the structure into the opening | from 4 650₸ per m² |
| Window installation to GOSTwith vapour and waterproofing of the seam | from 5 200₸ per m² |
| Single-sash PVC windowmanufacture and installation | from 42 500₸ per window |
| Double-sash PVC windowmanufacture and installation | from 65 500₸ per window |
| PVC window with installationstructure with fitting | from 60 000₸ per m² |
| Balcony unit with doorwindow and door as a set | from 95 500₸ per item |
| PVC window sill installationwindow sill fitting | from 5 500₸ per linear m |
| Drip sill installationexternal drip sill | from 3 250₸ per linear m |
| PVC reveals from sandwich panelsopening finishing | from 4 700₸ per linear m |
| Reveals for standard window turnkeyfull opening finishing | from 15 000₸ per window |
| Sealing of external seamssealing the seam outside | from 2 000₸ per linear m |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card or Kaspi
Clarify the estimate after measuringEight facts about our work: installation warranty, free measuring, price fixing and payment after installation.
for window installation work
the measurer will come at a convenient time
profile painting in window color (white, brown, gray)
daily 09:00–22:00 in Atyrau
the measurer selects fixings for the window profile and floor
we reply within 5 minutes
for double glazing replacement
for work and replaced components
Four steps from request to window handover

The measurer will come at a convenient time, take opening dimensions, help choose the structure and fixings.

The structure is made to the measured dimensions; the price is fixed in the order after measuring.

The crew composition, access to the apartment and cleaning after installation — the master agrees these details with the owner in advance.

Hardware care, leaf modes and seasonal adjustment — the master shows how to use the window so it serves for a long time.
Good to know
We handle pvc window installation atyrau homeowners can book with a free measuring visit, in-house installers and payment only after the work is done. We fit Economy and Prestige profiles, select fasteners for your floor and wind exposure, and back the installation with a 5-year warranty. Measuring and consultation cost nothing.
The measuring visit decides the whole job: it sets the size, profile, fasteners and final figure, and the price is locked only after it.
Our measurer comes at a time that suits you, takes every opening size and helps you choose the design, profile and fasteners on the spot. Measuring and consultation are free, and the visit covers each window and door in the flat. The measurer notes the wall material, the floor level and how the old frame sits in the reveal, because those three details decide whether Z-brackets, pins or magnets will hold the new unit against the wind. He also checks the sill and the slope, since a worn sill changes the height the new frame sits at. A measurement taken from the old frame alone often misses a sloped or out-of-square opening. This is how pvc window installation atyrau begins: the measurer records the true numbers on site, and those numbers carry through the whole job.
We fix the price in the order after measuring, so the figure you agree to reflects the real opening, profile and fittings. A quote given before the visit must assume a standard opening, and most openings here are not standard: walls run out of square, sills sit at different heights and reveals are wider at the top. Once the measurer has the true numbers, the order locks them and the amount does not move during installation. Pay after installation by cash, card or Kaspi, and the order stays open seven days a week if you need to change a detail. A fixed figure beats a low estimate that grows on the day.
Not every draught means a new window. We separate cases where repair or a fresh seal suffices from those needing full installation.
A warped frame, a failed glass unit that fogs between the panes, or rot around the reveal point to full installation rather than another repair. Once the profile has bowed, no adjustment brings the leaf back to a straight line, and the mounting seam stops sealing evenly. A glass unit that has lost its seal lets in moisture, so the low-e coating degrades and the room loses both heat retention and quiet. Condensation on the room side is usually a ventilation issue, while fogging between the panes means the sealed unit has failed and tuning will not clear it. Check the reveal for soft plaster and damp patches, because a sound opening keeps the job short and the finish clean.
Wind and dust off the steppe decide more of the spec than the catalogue: profile, glass unit and fastening all answer to the same load. Here is what drives each choice.
| Profile | Where it suits | Glass unit pairing |
|---|---|---|
| Economy | Sheltered low openings, interior partitions | Single or slim double unit |
| Prestige | Upper floors, exposed windward walls | Double unit with extra mass |
| Prestige with reinforced hardware | Large sashes, balcony doors | Heavier double or triple unit |
| Either, on a loggia | Glazed but unheated space | Double unit, lighter frame |
The installer selects fasteners for the frame and floor, because a high flat pulls harder on the structure than a sheltered low one. On upper storeys of a block facing the river channel we use Z-brackets and through-frame pins set into the wall, while a ground-floor opening in a private house often takes shorter anchors into brick or shell rock. Wall material matters as much as height: aerated block holds a different anchor than cast concrete, and the measurer checks it before the order is fixed. Gaps around a mounting seam show up as draughts on the windward side in winter, so the seam is sealed as carefully as the unit is fixed.
Installation day follows a fixed order: the old unit comes out, the new frame goes in, the seam is sealed and the sashes are adjusted, helping you plan the hours.
Clear the sill and floor within a metre of the opening and take down curtains before the team arrives, and most dust stays contained. Empty the tops of wardrobes and cover upholstered furniture with a sheet or plastic film — expanding foam sets fast and fine grit settles on every flat surface. Move plants and anything breakable to another room, and keep a free path from the door so the unit can be carried in without squeezing past boxes. Removing the old frame releases grit trapped in the reveal, so covering furniture in the same room saves a full clean afterwards. Ask installers to mask the reveal edges before sealing if the wallpaper is fresh — it spares patching later.
What happens after the team leaves matters as much as the finished installation. Here is what our guarantee covers, how to accept the job and when money changes hands.
| Work | Warranty | What it covers |
|---|---|---|
| Window installation | 5 years | Fit, mounting seam, adjustment |
| Glass unit replacement | 3 years | The sealed glazing itself |
| Window repair | 1 year | Labour and replaced parts |
The handover check and paying after installation You pay after installation by cash, card or Kaspi, once you have opened and closed every sash and checked the joint yourself. Walk the room with the team lead and test each handle through a full turn, then look along the mounting seam for gaps or squeezed foam. Ask for a demonstration of the drainage caps and the sash adjustment before the tools are packed. On a windy day, run a hand along the joint near the frame; a draught is easier to fix while the fitters are on site. Keep the signed handover sheet listing the profile, the sealed glazing and the date; we check it first if a claim comes in.
A balcony, loggia or veranda opening is not a flat window with a different view. Wider spans, stronger wind and old slopes change the whole job.
We glaze balconies, loggias, verandas and gazebos, where the frame often spans a wider opening and takes more wind than a flat window. On a loggia the unit sits inside a parapet and side walls, so the load spreads across several anchors. A veranda or gazebo is open on two or three sides, and the fastening plan must hold a span no single wall carries. The measurer checks the parapet material, floor level and height before choosing Z-brackets, pins or a combined layout. Such an opening is exposed on more than one side, so fastening and seam sealing matter more than the profile alone.
Old slopes rarely survive a swap intact, and an unfinished reveal lets wind and dust in around the new window. The crew removes the old unit, clears the opening, sets the new frame into the reveal, then seals the mounting seam with foam and tape on three layers. Slopes cut to the previous size usually do not close the new gap, so they are refitted or replaced after the frame is level. Skipping this leaves the foam exposed at the edges, and the reveal becomes the first place where draught shows up in winter. Refitting the slopes after the frame is set hides the mounting seam and protects the foam from sunlight.
A good installation rests on decisions in the right order: measure first, match frames and fixings to the building, accept the work on the spot, and keep the paperwork.
Selection, Fitting, Acceptance, Disposal
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionFor a windy side, choose a profile with reinforced steel and a multi-chamber design, plus hardware with compression. Make sure the fitters use storm fixings and seal the joint thoroughly.
First, the fitter removes the sashes and frame, then cleans the opening and installs the new unit with fixings. After that, they foam the joint, fit the sill, drip cap and reveals, and finally check the sashes and hardware.
Yes, if the profile and sashes are intact and the problem is cracks or fogging, replacing the double glazing is enough. If the frame is worn or the geometry is off, replacing the double glazing won't solve it — a new window is needed.
You can ask the fitters to take away the old frames and sashes — this service is often included in fitting. If you want to keep them for household needs, say so in advance.
Not always: the seal may be worn or the sash adjustment may have shifted. First, call a fitter — they will check the compression and the condition of the joint. If the profile is intact, a repair is often enough: the fitter will assess the window during a visit.
Open and close all sashes: they should move smoothly without sticking. Check for gaps at the reveals and sill, and feel the joint for drafts — there should be none. Also check that the installation is level.
For Atyrau's windy climate, a profile with reinforced steel and at least a three-chamber design is suitable. Look for hardware with compression and a quality seal — they better withstand wind gusts and keep out dust.
The fitting joint is the insulation layer between the frame and the wall that protects against drafts and moisture. If the joint is done properly, the window won't draft even in strong wind.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp