EPDM seal
The elastic rubber presses the sash tight again and keeps hot air out in summer and cold out in winter. From 1 000 ₸ per linear m.


EPDM seal
The elastic rubber presses the sash tight again and keeps hot air out in summer and cold out in winter. From 1 000 ₸ per linear m.

Premium seal
The German seal handles both summer heat and winter cold and resists cracking for a long time. From 1 200 ₸ per linear m.

Balcony seal
The balcony door seal works harder than any other, so it wears out first. A new seal costs from 5 000 ₸ per unit.

Brush pile
A worn brush on a sliding frame lets in dust and insects. We install a new one from 1 150 ₸ per linear m.

Inner seal
An extra seal between the sash and the frame keeps the room cool in summer and warm in winter. From 2 800 ₸ per window.

5,097 reviews on review sites
The sash is fine, but the window still lets in heat and cold? It's almost always the seal, and only the seal needs replacing.
The rubber seal runs along the grooves of the sash and frame and closes the gap between them. In summer the air conditioner runs at full power, yet hot air still gets into the room through dry rubber; in winter heat escapes the same way.
Temperature swings from summer heat to winter wind in Atyrau dry out rubber quickly. The technician removes the old seal, cleans dust from the grooves and installs a new one matched to your window brand.

per linear metre of seal including the technician's work
warranty on the work and the new seal
checking the window: cash, card or Kaspi
Four signs that your window needs servicing.

Dried-out rubber doesn't compress or spring back; the sash closes but a gap remains.
Sun and frost crack the seal, and dust gets into the room through them.
A loose piece hangs out of the groove, leaving a gap along the whole sash.
If the window gives off heat in summer and cold in winter, the seal no longer holds the sash tight.
We match it to the window and the room: a durable premium seal for a sunny kitchen, a wear-resistant seal for a balcony door.
standard PVC windows

An elastic seal for most profiles that doesn't melt in heat or crumble in winter.
sunny side

German rubber ages more slowly in sun and temperature swings and lasts longer than standard.
balcony access

A tight seal for a door that opens dozens of times a day.
aluminium sliders

Dense bristles close the gap at the runners against dust, midges and wind.
bedroom, kids' room

A third contour keeps the cool in summer and the warmth in winter, and dampens street noise.
The price depends on the perimeter of the sashes and the type of seal; the technician will give it before starting work.
| Type of work | Price |
|---|---|
| Seal replacement on the sashEPDM seal | from 1 000₸ per linear m |
| Premium sealmade in Germany | from 1 200₸ per linear m |
| Full window resealall seals of one sash | from 3 500₸ per window |
| Balcony door sealfull perimeter seal | from 5 000₸ per unit |
| Brush pile for aluminiumsliding systems | from 1 150₸ per linear m |
| Seal maintenancecleaning and lubrication | from 750₸ per linear m |
| Installation of inner sealadds one more layer | from 2 800₸ per window |
| Draught gap sealingaround the whole perimeter | from 3 500₸ per sash |
| Basic adjustmentsash pressure adjustment | from 3 000₸ per sash |
| Liquid plastic seamframe corners and joints | from 1 500₸ per linear m |
| Wooden window insulationSwedish method | from 4 200₸ per linear m |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Book a technicianA few reasons why our customers trust us with their windows.
on replacement and on new components installed
seals for KBE, Rehau, VEKA, Provedal and others
the amount is fixed after inspecting the window
the work: cash, bank card or Kaspi
the usual wait for a reply on WhatsApp
we come on weekdays and at weekends
we take requests every day
we work across Kazakhstan
The process from message to window check.

Send a photo of the sash on WhatsApp and briefly describe the problem: heat, draught, paint on the seal or moisture.

The technician checks the seal, hardware and pressure, identifies the profile brand and gives the price straight away.

We remove the old contour, clean the grooves and lay the new seal in a single piece around the sash perimeter.

We adjust the sash to the new seal, check the window for draughts, then you pay for the work.
Good to know
We handle window seal replacement in Atyrau with our own fitters, not subcontractors. A free measuring visit comes first, the price is fixed in the order after measuring, and you pay only after the work is done. Every seal replacement carries a 1-year warranty on labour and replaced parts.
Draughts and condensation on a closed window almost always point to the seal, though not always — first we separate a worn gasket from a leaf that has simply dropped out of adjustment.
We check the leaf geometry first, because a dropped hinge pulls the sash away from the gasket and mimics a worn one. A leaf that sags by even a couple of millimetres at the handle corner opens a gap over the full height of the frame, while the seal itself may still be soft and intact — in that case the fix is adjustment of the hinge, not new material. Frost on the profile and mould in the lower corner are the two signs that the gap has been open long enough for warm indoor air to reach the cold edge. If the gasket looks intact but the draught sits at the handle side, adjustment usually solves it and no new seal is needed — worth knowing before you pay for material.
Local wind, dust and sharp temperature swings decide how long a seal survives, so the material and the fit matter more than the label on the roll.
| Seal type | Best for | How it ages |
|---|---|---|
| EPDM | Windy, dusty climates | Stays elastic through frost and heat |
| TPE | Standard PVC windows | Good rebound, softer in extreme cold |
| Rubber | Budget refits | Hardens and cracks sooner |
We match the seal to the groove of your profile, so it fits KBE, Rehau, VEKA, Provedal and other systems without trimming that breaks the contour. The frame and sash take different sections — a contour seal runs around the frame rebate, a sash seal sits in the groove where the sash meets it, and the two only close tight when both match the profile depth. On the windy side of a building the gap opens first, and that is where dust enters and whistles through. Our measurer checks the groove width and the corner joints before choosing the section, then presses a sample length in to confirm the rebound. A seal pressed into the wrong groove leaves a gap at the corners where dust settles first — the fit at the corner tells you more about quality than the material label.
From the free measuring call to the final hinge adjustment, here is what actually happens on the day and how much time a flat with several windows takes.
The measurer comes at a time that suits you, takes sizes and helps choose the seal, then the fitter replaces the material and adjusts the sash in the same visit. Measuring and consultation are free, and the specialist brings samples of profiles and seal grades so the choice is made on the unit itself. On the fitting day the old gasket is pulled from the groove, the channel is cleaned of dust, and the new length is pressed in without stretching. The fitter then checks the leaf against the frame, adjusts the hinges and confirms the lock engages at every point. Most leaves stay on their hinges during the swap, so there is no need to empty the sill or move furniture. Window seal replacement in Atyrau follows this same order, so you know exactly what to expect on the day.
Seals wear out on far more than plastic frames. This section covers the window types, profiles and door units where a seal can be swapped without touching the sash, the glass or the fittings.
We re-seal PVC, wooden and aluminium units, plus balcony doors and loggia glazing, working with the seal groove each frame actually has. Plastic systems hold a standard slot, so a fresh EPDM or TPE gasket drops straight in; aluminium sliding sections and Provedal-type profiles often use a thinner channel that takes a narrower cord. Timber is a separate job, because the rebate is cut by the joiner rather than extruded to a fixed size, and older frames can sit slightly out of square after years of heat and dust. We also handle small vents, glazed loggias and the seals on gazebos and verandas, where the material presses against a moving leaf rather than a fixed pane. Wood often needs a different profile than PVC because the groove is shallower — a fitter carrying one type only will leave a gap you notice by winter.
We replace seals on units from any manufacturer, including KBE, Rehau, VEKA and Provedal, so the frame itself stays in place. The gasket is a consumable strip that compresses against the leaf; once it hardens or flattens, the structure is still sound and only that cord has failed. A full swap means removing the sash, breaking the reveal, refitting and re-plastering, while a re-seal is a matter of pulling the old strip, cleaning the groove and pressing in new material. On our visits we see plenty of frames that owners were told to replace when the only real fault was a perished gasket at the hinge side. Fresh material restores the draught barrier at a fraction of the disruption of a full swap — the frame, glass and fittings all stay as they are.
A clear guarantee, payment only once the job is done, and a booking that fits your week — three terms that decide whether a repair feels safe. Here is what each one means.
Every seal replacement we carry out comes with a 1-year warranty that covers both the labour and the replaced parts. The same term applies to window repair on the unit itself, so a gasket that starts letting draught through within twelve months is put right at no extra cost. The guarantee is tied to the sheet from the first call-out, which records the seal type, the profile it was fitted to and the fixed price agreed after measuring. Keep that sheet — it lists the seal type and the locked price, which is what the guarantee is checked against if a claim ever comes up.
A worn seal is a repair job, not a reason to change the whole window. The points below sum up what decides whether the fix holds through local wind and dust.
Seal wear, draughts, types, DIY replacement
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionRun your finger along the seal: if it feels hard, cracked or has lost its elasticity, it's time to replace it. Other signs are draughts from a closed window and condensation on the inside of the frame.
Most often the cause is a worn seal that no longer fits tightly against the frame. Less often it's an out-of-adjustment sash or a worn locking mechanism — a technician will identify this during an inspection.
In theory you can, but without experience it's easy to choose the wrong type and size of seal and damage the profile. A technician will select the right seal and replace it, with a 1-year warranty on the work.
Rubber (EPDM) is the most common, elastic and frost-resistant. Brush seals are used on sliding aluminium systems for dust protection, while silicone is more heat-resistant but more expensive and holds its shape less well.
You can replace it only on the problematic sash, but if the seal is worn in one place, it has likely lost its properties around the entire perimeter. During the inspection, the technician will advise where partial replacement is sufficient and where it's better to replace the whole perimeter.
In most cases the sash doesn't need to be removed: the seal is replaced in place by carefully taking the old one out of the groove. The sash is only removed if it obstructs access or has sagged significantly — the technician decides this during the inspection.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp