Seam under the sill
An open seam under the sill lets wind and moisture under the frame. Sealing — from 2 000 ₸ per linear metre.


Seam under the sill
An open seam under the sill lets wind and moisture under the frame. Sealing — from 2 000 ₸ per linear metre.

Swedish method
A rubber seal in the frame groove closes the gaps of an old window. From 4 200 ₸ per linear metre.

Warm balcony
We insulate sashes and walls so the balcony doesn't chill the room. From 6 800 ₸ per m².

Seal
A new seal and adjustment close gaps around the sash perimeter. From 1 000 ₸ per linear metre.

Window sill
We fill voids under the window sill and seal the seam — from 15 000 ₸ per job.

5,097 reviews on review sites
In winter the window lets heat out, in summer it lets heat in. By closing gaps, we solve both problems at once.
Heat and cool escape through the same places: the seam under the sill, gaps in the wooden frame, loose balcony sashes and thin glass. The technician finds them, closes them and adjusts the sashes.
Atyrau's climate is harsh: icy wind in winter, intense heat in summer, and the humid air by the river damages seam foam. That's why a tight window pays for itself twice a year.

linear metre of outer seam sealing
warranty on repair and components
we respond to requests on WhatsApp
What we find in Atyrau apartments and houses.

An old wooden window dries out and gaps around the perimeter let in cold wind.
Moisture and wind get under the frame from outside and chill the window sill.
Loose loggia sashes chill the adjacent room.
Single-chamber glass is cold in winter and lets in a lot of heat in summer.
We choose by window: Swedish method for wood, seals and seams for plastic, sashes and walls for the balcony.
outer seam

Sealant under the sill protects the seam from wind and moisture.
wooden frames

Milled groove and rubber along the entire sash length.
inside

Insulation of walls, floor and ceiling of the balcony or loggia.
at the frame

Liquid plastic protects the foam from indoor moisture.
windows against wind

Third rubber contour between frame and sash.
The total depends on the window type and scope of work; the technician will give it after inspection.
| Type of work | Price |
|---|---|
| Full window insulationeverything the window needs | from 3 800₸ per window |
| Sash sealnew seal | from 1 000₸ per linear metre |
| Draught checkfinding and fixing | from 3 500₸ per sash |
| Inner seamliquid plastic | from 1 500₸ per linear metre |
| Outer seamsealant under the sill | from 2 000₸ per linear metre |
| Revealinsulation, finishing | from 19 900₸ per linear metre |
| Window sillfilling voids | from 15 000₸ per job |
| Swedish method for woodseal in the groove | from 4 200₸ per linear metre |
| Pressure adjuster or micro-lifttight closing | from 1 700₸ per item |
| Inter-frame sealthird contour | from 2 800₸ per window |
| Thermal cameradiagnostics | from 9 000₸ per job |
| Balcony insidewarm balcony | from 6 800₸ per m² |
The price is fixed in the order after measuringMeasuring and consultation are freePayment after installation: cash, card, Kaspi
Order a technicianWhat you get.
on work and parts we replaced
we work with old and new windows
the amount is fixed after inspection
work: cash, card, Kaspi
on WhatsApp to a window photo
we visit on weekends too
we accept requests daily
we work across Kazakhstan
Simple and in one visit.

Describe on WhatsApp where it is cold or hot by the window and attach a photo of the frame and window sill.

The technician checks the sill, seams, frame and sashes and gives the price before starting work.

We seal seams outside and inside, install rubber, and insulate the balcony if needed.

We check the window for drafts together with you, then you pay for the work.
Good to know
Window insulation in Atyrau starts with a free measuring visit, where our measurer finds where the cold gets in and picks the fix: new weatherstripping, tighter hardware, sealed joints or a new glass unit. Our own fitters do the work, and you pay only after it is done.
A closed handle does not mean a sealed window. Cold air finds four typical paths into a flat, and the right fix depends on which one is open.
Water on the glass and frost along the edge point to a cold surface — either a weak glass unit or a leak that keeps the inner pane chilled through the night. A single-chamber unit in an old wooden frame collects moisture in the lower corners first, while frost along the hinge side usually means the leaf is not pressed tight. The pattern matters more than the amount: a wet centre with dry edges speaks about the glass, wet edges with a dry centre speak about the seal. Before ordering anything, check the room's airflow — sealed rooms with no vent produce the same condensation even on a sound unit, so the fix may be ventilation rather than insulation.
Our fitter works from the outside in — checking the seal by hand, testing how the handle pulls the leaf, and looking for gaps at the joint and slope before naming a single fix. He runs a palm along the perimeter on a cold morning, then opens and closes the sash to feel whether the hardware draws it in evenly, since an uneven pull points to worn hinges or a shifted frame. The joint under the sill gets the same attention, because foam shrinkage there is common on upper floors, and a thin feeler gauge confirms what fingers miss. On the free measuring visit we confirm the cause on site, and the price is fixed in the order afterwards.
Insulation is not one product but a short list of jobs, and the right combination depends on what the measuring visit finds at your unit.
| Layer | What we check | Typical fix |
|---|---|---|
| Seal | Weatherstripping along sash and frame | Replace worn weatherstripping |
| Hardware | How tight the sash closes | Adjust hinges and locking points |
| Joint and slopes | Gaps at frame edge and slope | Seal the joint, repair the slope |
| Glass | Inner pane temperature | Replace the glass unit if needed |
Most of our insulation work happens on the unit as it stands — we remove the old seal, adjust the hardware and seal the joint without taking the frame out of the wall. Window insulation in Atyrau often comes down to these small jobs rather than a full replacement. A two-pane sash that rattles in the wind usually needs new weatherstripping along the rebate and a quarter-turn on the hinge screws, taking minutes rather than hours. When the draught comes from the joint between the window and the wall, we clean the gap, prime the surface and run a fresh bead of sealant from inside, so no scaffolding or street-side access are needed. The glass unit stays in place unless it has fogged between the panes.
The weatherstripping is the cheapest part of the window and the first to fail, so knowing when to replace it saves the most heat for the least work.
We replace weatherstripping in windows of any manufacturer, including KBE, Rehau, VEKA and Provedal profiles, matching the seal to the groove the frame already has. The fitter measures the groove depth and width, checks whether the sash sits square, and picks a profile that fills the gap without forcing the handle to lock. A loose or oversize strip is the usual reason a fresh gasket starts leaking within a season. The gasket profile matters more than the brand name on the frame — a correctly matched profile seats deeper and lasts longer than a generic strip forced into the wrong groove. If the rubber is sound but the frame has shifted, the fix belongs to repair rather than replacement.
Not every cold unit needs replacing, and not every old frame can be saved. The choice depends on the frame, the pane and the unit type.
| Situation | What we recommend | Why |
|---|---|---|
| Sound frame, draught at edge | New weatherstripping and adjustment | Leak sits at the seal |
| Pane cold, frame fine | Glass unit replacement | Inner pane is the cold surface |
| Gap open behind frame | Seal the gap and slope | Cold path runs around the frame |
| Warped or rotten frame | Full window replacement | Insulation cannot straighten timber |
We insulate plastic, wooden and aluminium units, including balcony, loggia and gazebo glazing, and each type takes a different approach to the seal and the gap. On timber the weatherstripping sits in a routed groove and dries out faster than on plastic, so the seal is usually the first part to renew. Aluminium profiles conduct chill through the metal itself, which makes the joint behind the casing and the thermal break the places to check before touching the glass. Balcony and loggia glazing is measured and sealed like a room unit, only the fixings are chosen for the profile depth and the floor.
A free visit opens the work, a fixed plan carries it through and a simple self-check closes it — all backed by written cover.
Our measurer comes at a time that suits you, checks the seal, the hardware and the joint, and fixes the price in the order before anything begins. Measuring and consultation cost nothing, and the fitter looks at more than a tape measure: how the sash sits in the frame, whether the weatherstripping has flattened along the hinge side, and how the mounting joint meets the wall. A framed screen made to your size takes 10–15 minutes, a pleated one 40–60 minutes, so most households are finished in a single call. We open seven days a week and reply on WhatsApp within five minutes.
A draughty window has a specific, findable cause, and the sections above trace it to the seal, the hardware, the joint or the pane.
Insulation for old windows, seals, winter preparation, timelines
Konstantin Selenenkovsenior mosquito screen specialist, 10 years in the tradeOnline · replies within 5 minutes
Ask a questionYes, if the profile and double glazing are in good condition, window insulation can help without replacement: the technician will replace the seal, adjust the sashes and seal the joints. What exactly the window needs is determined after an inspection.
Most often, draft occurs due to worn seals, weak sash pressure or an unsealed joint. Window insulation includes replacing the rubber, adjusting the hardware and foaming the joints — after that, the draft disappears.
Before the cold weather, it is worth checking the seal, sash pressure and joints. Winter window insulation involves replacing worn rubber, adjusting the sashes and sealing the reveals, so the window stops freezing.
For such a climate, an EPDM or TPE seal is suitable — they are resistant to temperature fluctuations and UV. The specific type depends on the window profile, and the technician will select the appropriate one.
Window insulation is not limited to the seal: the technician also seals the installation joint, insulates the reveals if necessary and adjusts the sashes. A comprehensive approach gives a lasting result.
The time depends on the window and the scope of work, so the exact time is given after inspection. The technician performs the work on site.
Thank you. We will call you back within 10 minutes!
Your order number is on the receipt or in the SMS. Choose where to leave your review.
Write a review on WhatsApp