Craftsman with a screwdriver by a window handle in an office
from 1 250 ₸Free measuring visit and inspection in Almaty, we work without days offCalculate

PVC Window Repair in Atyrau

Hardware stuck

Hardware repair

Repair or replacement of sash hardware: labour from 7 800 ₸, parts paid separately

A craftsman holds a brush and a can of silicone lubricant for window hardware
GoogleYandex MapsZoon

5,097 reviews on review sites

What PVC window repair in Atyrau includes

The technician restores the parts responsible for closing, pressure and warmth in the home

How the service works

Plastic window repair means restoring the moving and sealing parts: hardware, handle, scissor arms, blocker, hinges and seal. The technician checks how the sash moves in the frame, whether the pressure is even around the perimeter, and whether there are cracks in the double glazing.

On site, they determine what can simply be adjusted and what needs replacing. If hardware or seal wear is minor, adjustment and lubrication are enough. When a part is worn out or the double glazing is damaged, the unit is replaced entirely — this restores pressure and thermal insulation without replacing the whole window.

Technician repairs the hardware of a white plastic window
1 year

warranty on work and replaced components

Free

measuring visit and inspection in Almaty

Without days off

we accept requests daily

What we repair
HardwareHandleScissor armsHingesSeal

How plastic window faults are fixed in Atyrau

Six typical situations the technician arrives for and what they do on site

A close-up of a plastic window corner with a new locking cam and hinge
  • 01Hardware stuck, handle won't turn

    If the handle turns with effort or jams, the technician checks whether debris is in the way and whether there is enough lubrication in the mechanism. When part wear is visible, only hardware replacement helps.

  • 02Sash opened in two modes at once

    This mode is dangerous for the sash and frame: trying to close the window can bend the scissor arms and damage the profile. If the fault is left until winter, the sash may warp and repair will cost more.

  • 03Hardware scissor arms broken

    The scissors mechanism is responsible for tilting the sash. The technician replaces the part and checks that the sash locks back into the required positions.

  • 04Sash has sagged

    Sagging is fixed by adjusting the hinges: the technician levels the sash so it doesn't catch on the frame and closes first time.

  • 05Draughts around the perimeter

    The technician checks the compression and the condition of the seal. If the rubber has lost its elasticity, it is replaced; if the problem is with the cams, the compression is adjusted.

  • 06Handle broken

    A standard handle is replaced on site: window handle replacement costs 2 750 ₸ per piece. The technician will select a model to match the colour and opening side.

Types of parts for plastic window repair

Parts and materials the technician brings along: original or compatible equivalent

Window handle

Standard, colour-matched to the window

Technician holds up a new white handle for a plastic window

Replaced if broken or sticking. We select according to the opening side and profile.

from 2 750 ₸/pc.

Hinges

Sash-mounted

A craftsman holds an L-shaped steel hex key for adjusting window hinges

New hinges eliminate sagging and squeaking. The technician levels the sash.

from 4 750 ₸/pc.

Scissors and switch

Part and labour

A master holds a small double-glazed unit sample with two glass sheets on his palm

Restore the correct opening pattern and locking in modes.

from 5 500 ₸/pc.

Cam and strike plate

Minor repair

A craftsman holds a brush and a can of silicone lubricant for window hardware

Cams and strike plates are responsible for compression. They are replaced individually without dismantling the sash.

from 1 300 ₸/pc.

Seal

KBE, Rehau, VEKA, Provedal

A master holds a coil of grey rubber window seal on his palm

We replace seals in windows of any manufacturer. Restores compression around the perimeter.

from 1 250 ₸

PVC window repair prices in Atyrau

Price list for work and parts; the exact cost is confirmed in the order after measuring

Type of workPrice
Simple sash adjustmentwithout removing the sashfrom 3 000₸ per sash
Complex sash adjustmentwith sash removalfrom 4 000₸ per sash
Balcony door adjustmentsash and rebatefrom 6 000₸ per unit
Hardware repairparts not includedfrom 7 800₸ per job
Sash hardware replacementkit for one sashfrom 10 000₸ per sash
Scissor arm or corner switch replacementpart and labourfrom 5 500₸ per unit
Cam or strike plate replacementminor repairfrom 1 300₸ per unit
Hinge replacementsash mountingfrom 4 750₸ per unit
Window handle replacementstandard handlefrom 2 750₸ per unit
Conversion to tilt-and-turn openingchange of opening schemefrom 19 000₸ per sash
Conversion of fixed window to openingsash insertionfrom 28 000₸ per sash
Micro-lift or extra pressure device installationadditional hardwarefrom 1 700₸ per unit
Balcony latch installationon balcony doorfrom 3 750₸ per unit
Unlocking a jammed sashwithout damaging hardwarefrom 2 400₸ per sash
Hardware cleaning and lubricationpreventive maintenancefrom 1 250₸ per sash

Price is confirmed in the order after measuringMeasuring and consultation — freePayment after installation: cash, card or Kaspi

Check repair cost

Why customers order plastic window repair in Atyrau from us

Facts about the company that matter when choosing a window repair technician

Repair warranty1 year

for work and replaced components

We workNo days off

we accept requests every day

Visit in AlmatyFree

inspection within the city

PaymentAfter installation

cash, card or Kaspi

Coverage17 cities

of Kazakhstan where you can order the service

SealAny brand

KBE, Rehau, VEKA, Provedal, etc.

Double glazingUrgent

manufacturing and replacement in a short time

WhatsApp response5 minutes

during working hours

How PVC window repair is carried out at your home

Four steps from request to checking the window after repair

  1. A hand holds a smartphone with a dark screen next to a plastic window
    015 minutes

    Request and consultation

    You describe the problem via WhatsApp or phone. The technician clarifies the symptoms and suggests a visit time.

  2. A tape measure lies along the opening of a plastic window on a light windowsill
    02By agreement

    Visit and inspection

    The technician agrees a convenient visit time and asks for access to the window. In Almaty, visit and inspection are free.

  3. A master holds a new white window handle on his palm and checks its fixing with a screwdriver, screws on the workbench
    03On site

    Repair

    The technician performs the work with the parts brought along. The price is confirmed in the order after measuring.

  4. A finished plastic window with a new handle and an even sash after repair
    04After repair

    Check and recommendations

    Together you check how the sash closes and whether compression holds. The technician explains how to care for the hardware.

Good to know

PVC Window Repair in Atyrau from the Centre Okon Team

Centre Okon handles PVC window repair in Atyrau with its own technicians, not through an aggregator. We diagnose the fault first, then fix it: seal replacement, sash adjustment, glass unit swap or insulation. Measuring and consultation are free, we work seven days a week, and every repair carries a 1-year warranty on labour and replaced parts.

Repair or Replace Your PVC Window

Repair is justified more often than owners assume. Replacement becomes the honest option only when the profile itself is worn through or the frame geometry has shifted, so read the criteria below before booking anything.

When a PVC Window Can Still Be Repaired

  • Draught along the sash edge: the seal has flattened with age, and a new gasket restores a tight fit in one visit.
  • Handle that turns hard: the hardware has lost its grease and alignment, so it needs adjustment and lubrication rather than a new unit.
  • Sash catching on the sill: the hinges have dropped under the weight of the glass, and re-hanging brings the sash back to level.
  • Water on the inner sill: the drainage slots are blocked with dust and leaves, so cleaning them clears the pooling.
  • Mist between the panes: the sealed unit has failed, and only that unit is swapped while the frame stays in place.

When Replacement Makes More Sense Than Repair

Replacement is the honest answer when the profile itself is cracked, the frame is out of square, or the window has been repaired repeatedly without holding. A bowed frame cannot be pulled straight by new seals or hinges, and every visit buys a few months rather than a fix. If a repair would cost close to a new unit and the frame is already worn, we say so before starting work rather than after. When the profile is sound but the glass has failed, only the sealed unit is replaced, and that work carries a 3-year warranty. Full window installation comes with a 5-year warranty on the fitting, and a sound frame is worth keeping for exactly that reason. If you are weighing up pvc window repair atyrau, the same criteria apply: a sound profile is worth repairing, a worn one is not.

Why Your PVC Window Repair Is Drafty or Hard to Close

A draught or a leaf that fights back when you close it are the two most common reasons people call a technician. Each symptom has its own cause and its own fix.

Finding the Source of a Draught

A draught that persists with the leaf closed almost always traces back to a compressed seal, a loose hinge or a misaligned locking point, not to the glass. The rubber flattens with years of sun and temperature swings, so the gap opens first at the corners and along the hinge side. A loose fitting pulls the leaf slightly out of the frame, and the lock no longer presses it tight against the rubber. We check all three on site before touching anything, because swapping a gasket on a window that only needed a hinge turn wastes your money. Run a hand along the rubber on a cold morning — a steady cold stream at one spot narrows the fault to that section before a technician arrives.

A Sagging Sash and What Adjustment Fixes

A leaf that drags or won't latch is usually an adjustment job, not a broken window, and we correct it on site without removing the leaf. The panel hangs on its fittings, and over time the screws work loose or the plates shift under the weight of double glazing. Turning the adjusting screw moves the leaf up, down or sideways and restores the gap that lets the lock engage. Our technician carries hex keys and spare parts for the common profile systems and works through the full swing of the leaf, not just the latch point. Small tweaks are within reach of a careful DIYer, but overturning a screw on a worn fitting can drop the panel — if the leaf already drags, call a technician.

Seal and Hardware Service for PVC Window Repair

Gaskets and moving parts wear out faster than anything else on a window. Here is how often they need attention, and what the technician brings on the visit.

How Often a Window Seal Needs Replacing

A seal wears out sooner on units facing direct sun or constant wind, and a flattened strip is replaced once it stops springing back. The rubber gasket runs along the sash and frame profile, and it is the first part to lose elasticity: on KBE, Rehau, VEKA and Provedal systems alike it flattens where the sash presses hardest, usually at the handle side and the bottom edge. We replace the gasket on windows of any manufacturer, matching it to the profile rather than forcing a universal strip into the groove. A strip that looks intact can still have gone flat — press it with a fingernail, and if it does not spring back, it is no longer sealing even without visible cracks.

What the Technician Brings and How Long It Takes

  • Seal stock: gaskets for KBE, Rehau, VEKA and Provedal profiles, so most windows are serviced in one visit.
  • Fittings kit: hinges, locking cams and handle parts for the adjustment that usually follows a worn gasket.
  • Hand tools: the technician brings what is needed to lift the strip without scratching the frame.
  • Lubricant: the groove is wiped, the new strip seated dry, then the moving parts greased.
  • Closing check: the technician tests sash pressure and lock points before leaving, so the window shuts evenly.

A Foggy Glass Unit and Same-Day Replacement

Condensation between the panes is not cosmetic damage. It points to a broken seal, so we look at why the glazing cannot be repaired on site and how a fresh one is fitted.

Why Fog Inside the Glass Unit Means Replacement

Moisture trapped between the panes means the glazing has lost its gas fill, and that seal cannot be restored on site, so the part is replaced rather than repaired. The cavity is factory-sealed around a desiccant spacer that absorbs residual humidity; once outside air enters, the desiccant saturates and the fog returns after every cold night. The window frame, sashes and hardware usually stay in place — only the glazed panel itself comes out. Wiping the inner surface does nothing because the mist sits behind the pane, and the only fix is a new factory-sealed unit fitted into the existing opening.

Same-Day Glass Unit Replacement

We can make and fit a replacement within one day when the size is confirmed, so a broken or foggy pane doesn't leave the room open overnight. The unit is assembled to the measured dimensions and dropped into the existing frame; our work comes with a 3-year warranty. Urgent production and fitting within 24 hours carries a surcharge on the part itself, so it is worth booking early in the day if the window is in a bedroom or a room you use in the evening. Measuring and consultation stay free, and the measurer confirms the exact size before anything is cut.

How a PVC Window Repair Visit Works

From the first message to a finished window, a repair visit runs through four steps. Below we explain who comes out, how long each stage takes and how to get the room ready.

From Your First Message to the Finished Window

  • First contact: send a photo of the window and a note on the fault, and we reply on WhatsApp within 5 minutes.
  • Measuring call: the measurer arrives at a convenient time, takes sizes and helps choose the design, mesh and fixings at no charge.
  • On-site diagnosis: a repair technician checks the sash, seal and hardware, then confirms what can be fixed the same day.
  • The repair itself: work is done on site, and the technician confirms the scope before starting.

Preparing the Room Before the Technician Arrives

  • Clear the sill: take off pots, glassware and decorations so the frame and hinges are easy to reach.
  • Pull furniture back: clear the floor under the window so the technician can reach the frame and hinges.
  • Free the approach: clear a path to the window so the technician can work without squeezing past furniture.

Warranty, Payment and What You Get in Writing

A written guarantee and a clear payment order are what separate a proper repair from a job done on trust. Below are the exact terms we put on paper and the point at which your price stops moving.

What the Warranty Covers

Coverage periods by type of window service
ServiceWhat is coveredTerm
Window repairLabour and replaced parts1 year
Glass unit replacementThe sealed unit itself3 years
Window installationFitting and adjustment5 years

When the Price Is Fixed and How You Pay

The price is fixed in the order after the free measuring visit, and you pay only once everything is finished, by cash, card or Kaspi. The measurer comes at a time that suits you, takes the sizes and helps pick the design and fixings, so nothing is agreed on a guess. Because the figure is locked in after measuring, it does not move if the task turns out to need an extra part on the day. This protects you from surprise charges and lets you plan the budget in advance, so ask for the full breakdown at the visit and check it matches what you expect. Keep that paper — it states the agreed scope and the warranty terms for the work, and it is your proof if any question arises later.

What Determines the Outcome of Window Repair

Most window faults come down to seals, hardware, adjustment or a failed glass unit, and each calls for its own remedy rather than a full swap.

  • Repair over replacement: a draught, a stiff handle or a sagging sash usually signals worn sealing or fittings, not a unit at the end of its life.
  • Mist between the panes: moisture trapped inside the sealed cavity means the assembly has lost its seal, and only a fresh one restores clarity.
  • Settle the scope first: agree the work list once measuring is done, so the figure in the order stays put when the technician starts.
  • Get the terms in writing: labour and replaced parts carry separate warranty periods, so read the document while the technician is still on site.

Questions about PVC window repair in Atyrau

Hardware, seal, double glazing, draughts

Konstantin SelenenkovKonstantin Selenenkovsenior mosquito screen specialist, 10 years in the trade

Online · replies within 5 minutes

Ask a question
01Can a plastic window be repaired if it has sagged due to hardware rather than the wall?

Yes, sagging caused by hardware is fixed by repair: hinges and the pressure are adjusted, and worn parts are replaced. If the misalignment comes from the wall or the opening, a specialist's inspection is needed first. They will determine the cause and advise on the next steps.

02What should you look for in a window seal for Atyrau's hot and dusty climate?

For heat and dust, a flexible seal that does not stiffen in the sun and maintains pressure is suitable. The specific type is selected by a specialist to match your window profile, depending on the window. Measuring and consultation for replacement are free.

03If the double glazing fogs up from the inside, is it repaired or only replaced?

Fogging from the inside means the double glazing's seal is broken, so it is not repaired but replaced. The frame and hardware can be left as they are. We carry out urgent double glazing replacement in Atyrau within a day.

04Can the seal on a KBE or Rehau plastic window be replaced if the installing company is no longer in business?

Yes, we replace seals in windows of any manufacturer, including KBE, Rehau, VEKA and Provedal, regardless of who installed the window. The specialist will select the material for your profile. Measuring and consultation are free.

05Can only the double glazing in a plastic window be replaced without changing the frame?

Yes, the double glazing is replaced separately from the frame: the old frame and hardware are kept if they are in good condition. The specialist will take measurements and select a new double glazing unit for your profile. Measuring and consultation are free.

06What should be done if a plastic window still has draughts after repair?

We provide a one-year warranty on window repair for work and replaced components. If the window has draughts again after repair, a specialist will inspect it and find the cause. The warranty covers the work performed and the parts installed.

Reviews of PVC window repair in Atyrau

5,0based on 97 reviews on platforms
All reviews